Frigidaire Washer Dryer Combo Valve

The Water Inlet Valve Assembly is an OEM part for Frigidaire washing machines. This assembly controls the flow of water into the washing machine during the fill cycles, ensuring the correct amount of water enters the tub.

Over time, the water inlet valve can become faulty due to mineral buildup, wear and tear from frequent use, or damage to the valve components. If the valve is not functioning properly, it can result in issues with the water flow into your washing machine.

Symptoms of a bad water inlet valve assembly include:

• No water entering the washing machine
• The washer filling slowly or not at all
• The washing machine filling with water when it is turned off
• Leaks from the valve area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Valve is an OEM part for Frigidaire laundry centers. It's a part that controls the flow of hot and cold water into the washing machine. By opening and closing at the appropriate times during the wash cycle, this valve ensures that clothes are washed in the correct temperature settings, optimizing cleaning performance and fabric care. 

Causes of a faulty Water Valve include mineral build-up from hard water blocking the openings, wear and tear causing leaks or malfunctions, and electrical problems such as faulty solenoids disrupting operation signals. 

Symptoms of a malfunctioning Water Valve include:

• Water not entering the washing machine, leading to dry wash cycles.
• Water entering the machine too slowly, indicating a partial blockage.
• Water leaking from the valve when the machine is off, suggesting a failure to close completely.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water inlet valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper filling and helps prevent unwanted water entering the unit between cycles.

• Opens and closes to regulate water flow when energized by the control
• Failure can cause no fill or very slow fill during cycles
• Can contribute to leaks at the back or water-inlet/fill error alerts

• Disconnect power and shut off the water supply before servicing
• Keep a towel or pan handy to catch residual water; relieve hose pressure
• Note/label hose and wire locations; transfer any brackets or screws from the original valve as needed
• Restore water and power, tighten connections, and check carefully for leaks with a test fill

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

This 115V water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water supply when the valve fails. Designed to replace a faulty solenoid valve and stop leaks or no-water issues. What it does

• Opens and closes water flow to the ice maker and door dispenser when energized.
• Commonly replaces valves that hum, leak, or fail to allow water flow.
• Stops intermittent or no-water conditions caused by a stuck or electrically failed valve.
• Works with the fridge's control signals to deliver water only when needed.

• One 115V water inlet (solenoid) valve as shown.

• Disconnect power and shut off the household water supply before replacing the valve.
• Verify electrical connections and water line fittings are tight and leak-free after installation.
• Handle inlet fittings carefully to avoid damage; use appropriate tools and avoid overtightening.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper water supply when the valve fails. Direct-fit replacement that helps stop leaks, no water flow, or intermittent dispensing. What it does:

• Opens and closes to allow water into the ice maker and/or door dispenser when requested
• Stops water flow when idle to prevent leaks and overfilling
• Common repair for no water, slow fill, or continuous dripping from dispenser or ice maker
• Electromechanical valve driven by refrigerator control signals

• Disconnect power and shut off the household water supply before starting
• Replace only with parts specified for your model;
• Inspect and tighten or replace inlet hoses and clamps if corroded or damaged