Parts for Ge DCCB330ED2KC: 02 - Front Panel & Door Parts

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

The Dryer Lint Filter Assembly is an OEM replacement part for GE dryers. It serves as a crucial barrier, preventing lint and other debris from accumulating in the dryer's internal components and exhaust system. This filter helps ensure proper airflow and drying efficiency while reducing potential fire hazards caused by lint buildup.

Symptoms of a bad dryer lint filter assembly include:

• Longer drying times due to restricted airflow
• Excessive lint buildup on clothing or in the dryer drum
• Overheating or hot spots within the dryer
• Visible signs of damage or wear on the lint filter housing or mesh

Causes of a bad lint filter can include excessive lint buildup, physical damage to the filter mesh or housing, or improper installation. A clogged or damaged lint filter can lead to decreased drying efficiency, increased energy consumption, and potential fire hazards.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw restores secure fastening for appliance components, helping stop loose panels and rattles. Use it to replace a missing or stripped fastener and keep assemblies aligned and stable. What it does

• Fastens panels, brackets, or small assemblies to maintain proper alignment
• Prevents vibration-related noise and movement from loose parts
• Replaces missing, worn, or stripped screws that allow components to shift
• Simple hardware solution that restores secure connections

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or nut driver to avoid cam-out or damage
• Start threads by hand to avoid cross-threading; tighten until snug
• Do not overtighten—excess torque can strip threads or damage parts

The Lint Chute Assembly is an OEM replacement part for GE dryers. This component plays a crucial role in capturing and collecting lint and other debris from the drying process, ensuring efficient airflow and preventing potential fire hazards.

Symptoms of needing to replace the lint chute assembly include:

• Reduced airflow or poor drying performance
• Visible lint buildup or clogging in the chute or exhaust area
•  Overheating or excessive heat buildup within the dryer
• Unusual noises or vibrations during the drying cycle

Causes of a faulty lint chute assembly can include normal wear and tear over time, clogging due to excessive lint accumulation, or physical damage due to improper cleaning or maintenance.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

The Lower Drum Felt seal is an OEM replacement part for GE dryers. The Lower drum felt seal is responsible for creating a seal between the drum and the front panel of the dryer.

This part fixes the following symptoms:

• Air leaking from the dryer drum
• Reduced dryer efficiency and increased energy costs
• Clothes becoming caught in the gap between the drum and front panel
• Potential damage or snags to clothes or the dryer

Causes of a bad Lower Drum Felt Seal can range from normal wear and tear, which degrades the felt material over time, to excessive load sizes that strain the drum and seal. Additionally, over time, the seal can become compressed or damaged, leading to a less effective seal and the potential for heat loss and inefficiency in the drying process.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Dryer Drum Front Support Bearing is an OEM part for GE dryers, designed to support the front of the dryer drum as it rotates. This crucial component ensures smooth and quiet operation by reducing friction and providing a stable surface for the drum to spin on. 

Causes of a bad Dryer Drum Front Support Bearing include excessive wear due to age or overuse, a buildup of lint and debris causing additional friction, or improper loading of the dryer, which can lead to uneven wear.

Symptoms of a bad Dryer Drum Front Support Bearing include:

• Unusual noises, such as squeaking or grinding, during operation
• Excessive vibration or shaking of the dryer
• The drum may have difficulty turning, or it may seem to be stuck
• Increased drying times if the drum is not spinning efficiently

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Green bearing slide that replaces a worn bearing guide in select GE laundry appliances, helping restore smoother drum movement and reduce vibration and noise from a misaligned bearing assembly. Fits where the bearing rides or is guided. What it does:

• Guides the bearing assembly for steadier drum rotation — symptoms include grinding, squeaking, or rough spin cycles.
• Helps correct minor drum wobble and imbalance caused by a worn guide surface.
• Protects the bearing mating surface from accelerated wear by maintaining alignment.
• Can improve spin stability and reduce abnormal vibration when the guide is failing.

• Disconnect power and water supply before beginning any repair.
• Part typically accessed by removing the washer front panel or tub components.
• Verify the part number and color match your machine before installing.

The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lint Screen Housing Seal is an OEM part for GE dryers. This seal is designed to fit around the housing of the lint screen, ensuring a tight seal that prevents lint and small particles from bypassing the filter and entering the dryer's internal components. This seal measures approximately 36” long.

Symptoms of a failing lint screen housing seal include:

• Increased accumulation of lint inside the dryer cabinet
• Decreased drying efficiency, requiring longer cycles to dry clothes
• Visible wear or gaps in the seal

Causes of wear or failure of the lint screen housing seal often include regular use, which can stretch or tear the material, exposure to high temperatures which can degrade the rubber or foam, and improper installation which can lead to a poor fit.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Switch is an OEM part for GE dryers, designed to ensure the dryer does not operate when the door is open. This safety feature is crucial for preventing accidents and ensuring the appliance operates efficiently and safely. The switch signals the dryer's control system about the status of the door—if it's open or closed—thereby allowing or preventing the start of a drying cycle. 

Causes of damage to the door switch often include mechanical wear from repeated use, accidental damage from loading or unloading, or electrical issues such as short circuits. 

Symptoms of a bad Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened
• Unusual noises or the dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Handle Door is an OEM part for GE dryers. This door handle allows for easy opening and closing of the dryer door, providing a secure grip to access the drum.  

Common causes for door handle failure include regular wear from frequent use, forceful handling, and material fatigue over time.  

Symptoms of a failing Handle Door include:

• Cracks or breakage in the handle
• Handle becoming loose or detaching from the door
• Difficulty in opening or closing the dryer door
• Visible wear that could affect the grip or usability

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a single replacement screw used to secure appliance panels and components. It provides a direct one-for-one replacement to restore proper fastening and help eliminate rattles or loose panels. What it does

• Secures trim, access panels, or internal components to prevent movement and vibration.
• Replaces stripped, missing, or corroded screws that cause loose or rattling parts.
• Restores proper alignment so doors, drawers, or panels close and sit correctly.
• Helps maintain safe, stable operation by keeping components fastened.

• Handle with care and use the correct screwdriver to avoid stripping the head.
• Tighten to a snug fit; do not over-torque which can strip threads or crack plastic.
• If the original screw was damaged or the mating thread is stripped, inspect the hole and replace with the correct OEM screw or insert as needed.
• Disconnect power or follow appliance-specific safety steps before accessing internal parts.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed