Parts for Ge DCCH485EK0MS: 03 - Front Panel & Door Parts

Dryer condenser cover that protects and encloses the condenser unit. Replace this cover if it's cracked, broken, or missing to restore proper appearance.

Replace your dryer's condenser cover if cracked, broken, or missing. This protective cap shields the condenser unit from debris and damage. Direct fit.

This complete front control panel assembly replaces the oven/range user interface and restores a clean, functional control surface for keypad and display operation. It provides the exterior bezel and mounting surface for controls and indicators. What it does:

• Replaces a cracked, warped, or damaged control panel to restore proper button access and a finished appearance
• Provides the mounting surface for the control board, keypad and display so touch inputs register correctly
• Helps eliminate symptoms like loose or missing buttons, visible panel damage, or an unstable control surface
• Restores proper alignment of trim and screw points for a secure fit on the appliance

• Disconnect power (unplug or shut off circuit breaker) before starting any repair to avoid shock
• Handle carefully to avoid scratching or damaging the display/window and trim during installation
• Remove mounting screws/panels as required and transfer any clips, gaskets, or trim pieces per service literature

Replace missing or stripped screws securing dryer panels and components. This M4 x 12mm screw restores proper assembly. Takes minutes with basic tools.

Replace your dryer's door hinge bracket if it's cracked, broken, or causing misalignment. This metal mounting bracket secures the door hinge assembly.

Tapping screw for dryer or refrigerator assembly. Replace this fastener if cracked, stripped, or missing during panel or component installation.

This is a hinge-header screw used to secure door hinge assemblies—provides the correct fit and thread size for a tight, stable hinge connection to keep doors aligned and operating smoothly. What it does:

• Secures the hinge header to the appliance chassis or door hinge assembly
• Restores proper hinge alignment to eliminate door sag or uneven closing
• Prevents looseness that can cause noise, rubbing, or misalignment
• Matches M5 thread and 12mm length for the intended hinge mounting point

• Support the door or hinge assembly before removing or installing the screw to avoid dropping or damaging the door
• Use the correct-sized driver to avoid stripping the head; tighten snugly but avoid over-torquing
• Disconnect power or follow appliance-specific safety procedures if removing panels near electrical components

This hinge holder secures the appliance door hinge assembly to the cabinet, helping keep the door aligned and operating smoothly. Designed as a direct-fit replacement to restore proper door support and movement. What it does:

• Supports and anchors the door hinge to prevent sagging or misalignment
• Keeps the hinge pivot point stable for smooth opening and closing
• Helps reduce wear on the hinge assembly and door seal gaps
• Commonly replaced when hinge mounting is broken, cracked, or worn

• One hinge holder

• High-level replacement — basic hand tools typically required; keep power off and remove power source when applicable
• Use care to support the door while removing or installing hinge hardware to avoid injury or damage
• Inspect hinge pins and surrounding fasteners; replace or tighten as needed per manufacturer guidance

If your dryer won't start or the door won't latch, this door strike may be worn or broken. Restores secure door closure. Simple 10-minute fix.

Hinge guide for dryer door installation. Replaces broken, cracked, or missing guides that help position and align the door hinge for proper operation.

Replacement door hinge for dryers. Supports and aligns the door for smooth opening and closing. Replace if cracked, broken, or worn for secure mounting.

M4x14 tapping screw for securing dryer panels and components. Replace if screw is stripped, missing, or no longer holding parts firmly in place.

Durable dryer door handle that restores smooth opening and closing. Replace your cracked, loose, or broken handle for secure grip and proper door operation.

This switch cover protects the front control switch assembly, keeping switches free of debris and helping maintain reliable control operation. It's a direct-fit replacement designed to restore the control panel's finished appearance. What it does:

• Shields the switch assembly from dust, spills and accidental contact
• Helps prevent switch sticking, intermittent operation or cosmetic damage
• Restores a secure mounting surface for the control switch
• Works with the existing switch hardware

• Disconnect power before starting to avoid shock or injury
• Access typically requires removing the control panel; keep fasteners and small parts organized
• Align cover over the switch assembly and secure with the original screws or clips
• Test controls after reassembly to ensure proper fit and function