Parts for Ge GTX60GBSJ0WS: Front Panel & Door Parts

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

The Dryer Lint Filter Assembly is an OEM replacement part for GE dryers. It serves as a crucial barrier, preventing lint and other debris from accumulating in the dryer's internal components and exhaust system. This filter helps ensure proper airflow and drying efficiency while reducing potential fire hazards caused by lint buildup.

Symptoms of a bad dryer lint filter assembly include:

• Longer drying times due to restricted airflow
• Excessive lint buildup on clothing or in the dryer drum
• Overheating or hot spots within the dryer
• Visible signs of damage or wear on the lint filter housing or mesh

Causes of a bad lint filter can include excessive lint buildup, physical damage to the filter mesh or housing, or improper installation. A clogged or damaged lint filter can lead to decreased drying efficiency, increased energy consumption, and potential fire hazards.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower Drum Felt seal is an OEM replacement part for GE dryers. The Lower drum felt seal is responsible for creating a seal between the drum and the front panel of the dryer.

This part fixes the following symptoms:

• Air leaking from the dryer drum
• Reduced dryer efficiency and increased energy costs
• Clothes becoming caught in the gap between the drum and front panel
• Potential damage or snags to clothes or the dryer

Causes of a bad Lower Drum Felt Seal can range from normal wear and tear, which degrades the felt material over time, to excessive load sizes that strain the drum and seal. Additionally, over time, the seal can become compressed or damaged, leading to a less effective seal and the potential for heat loss and inefficiency in the drying process.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Top Bearing is an OEM replacement part for GE dryers. It is responsible for supporting the weight of the dryer drum and allowing it to rotate smoothly during the drying cycle. This bearing is located at the top of the drum and helps to maintain proper alignment and balance.

Causes of a bad top bearing can include regular wear and tear from continuous use, excessive friction due to lack of lubrication, or damage from foreign objects or overloading the dryer.

Symptoms of a bad Top Bearing include:

• Unusual squeaking, squealing, or grinding noises during operation
• Excessive vibration or shaking of the dryer drum
• Difficulty in rotating the drum manually
• Visible signs of damage or wear on the bearing itself

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Note: 10-watt bulb

The Lamp is an OEM part for GE dryers. This part illuminates the dryer's drum interior, enhancing visibility for loading and unloading garments. It ensures that users can easily see their clothes and any items inside the drum, particularly useful in low-light conditions. 

Replacing a non-functional dryer lamp is important for maintaining the functionality and convenience of your GE dryer, ensuring you can effectively manage your laundry. 

Symptoms of a malfunctioning dryer lamp include:

• A lack of light inside the drum when the dryer door is opened or during operation
• Flickering or intermittent light indicating a loose connection or nearing the end of the lamp's lifespan
• Complete failure to illuminate, which could stem from a burnt-out bulb or electrical issues within the dryer

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Bearing Slide Assembly is an OEM component for GE electric clothes dryers. As an integral part of the dryer tumbler system, this assembly includes the bearing slides that allow smooth rotation of the tumbler drum during drying cycles. 

Symptoms of faulty bearing slides include:

• Abnormal vibrations or shaking of the dryer cabinet 
• Noisy operation that gets louder over time
• Rubbing or grinding sounds coming from inside the machine
• Reduced tumbler movement or inability to manually turn the drum

Causes involve general wear of plastic bearing surfaces from years of drum rotation as well as potential damage or misalignment from excess stress on the slides.

This GE OEM replacement helps maintain balanced tumbler movement. Compatible with Hotpoint, RCA, and some Kenmore dryers using the bearing slide assembly design.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Front Drum Support Assembly is an OEM part for GE dryers. It supports the front of the dryer drum, allowing it to rotate smoothly during the drying cycle.

Causes of a bad front drum support assembly can include wear and tear from regular use, damage from foreign objects entering the drum, or deterioration of the support glides or rollers over time.

Symptoms of a bad front drum support assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The drum not rotating properly or getting stuck
• Visible wear on the support glides or rollers

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This complete microwave oven door assembly restores the oven's sealed cooking chamber and user access, helping stop heat or steam leaks and providing a secure, functional door surface. Use it to replace a cracked, bent, or non-closing door. What it does:

• Replaces the full microwave door so the oven seals and operates safely
• Restores the outer panel, inner trim and viewing area for normal use
• Helps resolve symptoms like a broken or cracked door, poor closure, rattling, or visible damage
• Re-establishes proper door alignment and latch engagement when installed correctly

• Disconnect power and unplug the appliance before beginning any repair
• Handle glass and trim carefully; wear gloves and eye protection if glass is cracked
• Installation may require removal of surrounding trim or control panel—retain all screws and fasteners

This door switch is an OEM replacement part for GE dryers. This switch is designed to promptly end the dryer cycle when the door is opened. The switch comes equipped with a metal lever arm and plunger that can be depressed to activate the switch.

Causes of a bad door switch can include normal wear over time from repetitive open/close cycles. Exposure to moisture, food drips or cleaning chemicals may also contribute to switch failure. 

Symptoms of a bad door switch are:

• The oven will not start a bake cycle with the door securely latched  
• Error codes displayed related to the door being open
• Inconsistent or unreliable door closure sensing  
• Failure to function properly after cleaning or moisture exposure

This OEM part is also compatible with ranges sold under Hotpoint and RCA brands and some Kenmore models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Door Strike is an OEM part for GE dryers. It ensures the dryer door securely latches when closed, allowing the dryer to operate properly. The door strike works with the door catch or latch mechanism, creating a tight seal to prevent heat and noise from escaping during the drying cycle.

A bad door strike can lead to issues with the door not closing or staying closed, resulting in poor drying performance and potential safety hazards. Causes of a bad door strike can include wear and tear over time, damage due to accidental impact or mishandling, or a faulty latch assembly.

Symptoms of a bad door strike include:

• Difficulty in closing or latching the dryer door
• Door opening during operation
• Visible signs of damage or wear on the door strike or latch assembly

Replace your worn-out or damaged door strike with this genuine OEM GE part to ensure a secure and reliable closure of your dryer door. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The HARNESS SENSOR ASSEMBLY is an OEM part for GE electric dryers. It is a comprehensive harness assembly that includes sensors to monitor temperature and moisture levels during drying cycles. These sensors relay crucial data to the dryer control board allowing for optimized cycle times and prevention of over-drying.

Symptoms of a bad harness sensor assembly include:

• Dryer cycles not running for full expected time durations   
• Clothes continually coming out damp rather than fully dried
• Dryer failing to advance through programmed cycles properly
• Error codes or faults displayed on the control panel 

Causes can arise from damaged or loose wiring connections, faulty sensors that provide inaccurate readings, or general failure over time due to environmental exposure.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.