Parts for Ge PTD60EBSR0WS: Front Panel & Door Parts

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

The Lint Filter Assembly is an OEM replacement part for GE dryers. This component is designed to capture lint and other debris generated during the drying process, preventing it from accumulating in the dryer's exhaust system and posing a potential fire hazard.

Symptoms of needing to replace the lint filter assembly include:

• Decreased drying performance or efficiency
• Visible damage, deterioration, or clogging of the filter
• Difficulty in removing or reinstalling the filter assembly

Causes of a faulty lint filter assembly can include normal wear and tear over time, excessive lint buildup or blockage, or physical damage due to mishandling or improper cleaning.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

This white front panel restores the visible exterior and protects the control area on compatible GE ranges. It replaces cracked, dented or discolored panels to give the appliance a clean, finished appearance and support for mounted components. What it does:

• Covers and protects the control console and internal components from spills, heat, and impact
• Restores worn or damaged cosmetic finish and helps the range look like new again
• Provides the proper mounting surface and alignment for trim and controls
• Helps prevent debris from entering internal compartments that can affect operation

• Disconnect power (and gas if applicable) before starting any service to avoid shock or injury
• Remove the existing front panel by removing retaining screws; handle edges carefully to avoid cuts
• Reuse original mounting hardware unless new hardware is explicitly included

These duct trap slides replace the moving rails that let the dryer's duct trap assembly open and close smoothly, helping restore proper vent access and reduce rattling or binding. Designed to match OEM fit and function. What it does:

• Guides the dryer duct trap so the trap door opens and closes smoothly
• Helps prevent the trap from sticking, misaligning, or making noise
• Restores proper vent access for cleaning and maintenance
• Works with the duct trap assembly to maintain a secure fit

• Recommended for experienced DIYers; unplug appliance and move away from the wall before beginning
• Remove front access panel or lint trap assembly to reach trap slides
• Inspect surrounding clips and fasteners; replace any damaged hardware to ensure secure fit

This duct trap channels dryer exhaust into the home venting system and helps catch lint and debris before it reaches the house ductwork. It restores proper vent routing for safer, more efficient dryer performance. What it does:

• Funnels dryer exhaust into the home's vent duct while capturing loose lint and debris
• Helps prevent lint buildup in the house venting path that can cause reduced airflow
• Restores correct alignment and connection between the dryer's exhaust outlet and ducting
• Commonly replaced when cracked, warped, missing, or not sealing properly

• Disconnect power (and gas if applicable) before beginning any work
• Remove dryer from the wall enough to access the exhaust outlet; some models require vent removal
• Inspect surrounding ductwork and replace any damaged venting or clamps as needed for a secure seal
• Use basic hand tools; ensure vent connections are tight and route venting to manufacturer guidelines

The Front Drum Support is an OEM part for GE dryers. This component provides critical support to the front of the dryer drum, allowing it to rotate smoothly and maintain proper alignment during the drying cycle. The support does not include bearing slides

A failing drum support can cause the drum to misalign or make unusual noises, leading to potential damage to other components and less effective drying performance.

Symptoms of a bad front drum support include:

• Unusual noises such as squeaking or grinding during operation
• The drum not rotating smoothly or being out of alignment
• Increased wear on the drum or other internal components
• Clothes taking longer to dry or coming out damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Felt Top Bearing is an OEM part for GE dryers. It provides a smooth surface for the drum to rotate on, reducing friction and wear on the drum and other components.  

Causes of a bad felt top bearing can include prolonged use, exposure to high temperatures, or the accumulation of lint and debris.  

Symptoms of a bad felt top bearing include:

• A squeaking or grinding noise during the drying cycle
• Increased friction, causing the drum to turn less smoothly
• Visible wear or damage to the felt material
• Clothes snagging or being damaged inside the dryer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Bearing Slide Assembly is an OEM component for GE electric clothes dryers. As an integral part of the dryer tumbler system, this assembly includes the bearing slides that allow smooth rotation of the tumbler drum during drying cycles. 

Symptoms of faulty bearing slides include:

• Abnormal vibrations or shaking of the dryer cabinet 
• Noisy operation that gets louder over time
• Rubbing or grinding sounds coming from inside the machine
• Reduced tumbler movement or inability to manually turn the drum

Causes involve general wear of plastic bearing surfaces from years of drum rotation as well as potential damage or misalignment from excess stress on the slides.

This GE OEM replacement helps maintain balanced tumbler movement. Compatible with Hotpoint, RCA, and some Kenmore dryers using the bearing slide assembly design.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Front Drum Support Assembly is an OEM part for GE dryers. It supports the front of the dryer drum, allowing it to rotate smoothly during the drying cycle.

Causes of a bad front drum support assembly can include wear and tear from regular use, damage from foreign objects entering the drum, or deterioration of the support glides or rollers over time.

Symptoms of a bad front drum support assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The drum not rotating properly or getting stuck
• Visible wear on the support glides or rollers

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This white dryer door replaces a cracked, dented, or discolored front door to restore appearance and proper closure. It's a direct-fit exterior door shell that helps keep laundry inside and the dryer looking finished. What it does:

• Replaces damaged or cosmetically worn dryer front door panels.
• Restores proper door closure for safe operation and heat containment.
• Helps prevent items from falling out and reduces heat/light leaks.
• Improves dryer appearance when the original door is scratched, cracked, or faded.

• One white outer dryer door

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Basic hand tools typically required; door may attach with screws and hinge clips—support the door while removing fasteners.
• Handle edges carefully to avoid scratches; align hinges and latch for proper closing.

The Lint Screen Housing Seal is an OEM part for GE dryers. This seal is designed to fit around the housing of the lint screen, ensuring a tight seal that prevents lint and small particles from bypassing the filter and entering the dryer's internal components. This seal measures approximately 36” long.

Symptoms of a failing lint screen housing seal include:

• Increased accumulation of lint inside the dryer cabinet
• Decreased drying efficiency, requiring longer cycles to dry clothes
• Visible wear or gaps in the seal

Causes of wear or failure of the lint screen housing seal often include regular use, which can stretch or tear the material, exposure to high temperatures which can degrade the rubber or foam, and improper installation which can lead to a poor fit.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Latch is an OEM part for GE dryers that keeps the dryer door securely closed during operation. It provides a secure connection between the door and the dryer cabinet to prevent any accidental openings while the machine is in use.

A bad Dryer Latch can occur due to regular use, wear and tear, or accidental damage. If the latch becomes worn, broken, or fails to engage properly, it can lead to issues such as the door popping open during a drying cycle or the dryer not starting at all.

Symptoms of a bad Dryer Latch include:

• Door not staying closed during a drying cycle.
• Difficulty in latching the door shut.
• Visible damage or deformation of the latch.
• Inability to start the dryer.

Replacing the Dryer Latch with this genuine GE part ensures a secure and reliable closure for your dryer door. This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This door hinge assembly replaces a worn or damaged hinge to restore proper door support and movement. It helps the door open and close smoothly and keeps the door aligned for a tight seal. What it does

• Supports and pivots the appliance door to enable normal opening and closing
• Restores proper door alignment to prevent rubbing, gaps or uneven sealing
• Reduces symptoms such as a sagging, loose or noisy hinge
• Works as the mounting point between the door and cabinet/frame

• One hinge assembly

• Always disconnect power (and water for refrigerators) before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Basic hand tools required; follow the appliance service manual for torque and fastener locations

This LED light assembly provides interior illumination for compatible refrigerators, restoring clear, energy-efficient light inside the fresh-food compartment. Replaces a failed or dim interior lamp to help you see food and shelves more easily. What it does:

• Replaces a burned-out or nonworking interior LED light assembly
• Restores steady, bright illumination when the door is open
• Helps eliminate flickering, dimming, or intermittent lighting issues
• Designed to fit the refrigerator's existing light housing and connector

• Disconnect power to the appliance before starting any work to avoid shock.
• Handle the LED module and connector carefully to avoid damage.
• Typically a direct plug-in replacement; follow the refrigerator's service manual for removal and installation.

This door switch is an OEM replacement part for GE dryers. This switch is designed to promptly end the dryer cycle when the door is opened. The switch comes equipped with a metal lever arm and plunger that can be depressed to activate the switch.

Causes of a bad door switch can include normal wear over time from repetitive open/close cycles. Exposure to moisture, food drips or cleaning chemicals may also contribute to switch failure. 

Symptoms of a bad door switch are:

• The oven will not start a bake cycle with the door securely latched  
• Error codes displayed related to the door being open
• Inconsistent or unreliable door closure sensing  
• Failure to function properly after cleaning or moisture exposure

This OEM part is also compatible with ranges sold under Hotpoint and RCA brands and some Kenmore models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

The HARNESS SENSOR ASSEMBLY is an OEM part for GE electric dryers. It is a comprehensive harness assembly that includes sensors to monitor temperature and moisture levels during drying cycles. These sensors relay crucial data to the dryer control board allowing for optimized cycle times and prevention of over-drying.

Symptoms of a bad harness sensor assembly include:

• Dryer cycles not running for full expected time durations   
• Clothes continually coming out damp rather than fully dried
• Dryer failing to advance through programmed cycles properly
• Error codes or faults displayed on the control panel 

Causes can arise from damaged or loose wiring connections, faulty sensors that provide inaccurate readings, or general failure over time due to environmental exposure.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

The Shoe Drying Rack is an OEM accessory component specifically designed for select GE dryers. As an added feature, this rack provides a convenient way to dry shoes along with regular laundry items. It allows wet shoes to be tumbled gently while being fully ventilated to dry effectively.

Symptoms of a bad shoe drying rack include:

• Broken or cracked rack supports that collapse the structure
• Missing hooks or attachment points to secure the rack in place  
• Rust, corrosion, or other damage that compromises its functionality

Causes of a bad shoe drying rack can include normal wear and tear over extended use, exposure to excessive heat levels, or damage from overloading or improper handling.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.