Parts for Ge YFD45ESPM0DG: Front Panel Parts

Captures lint and debris during drying cycles to prevent clogs and maintain airflow. Replace if torn, clogged, or damaged. Confirm fit with your model.

Seals duct connections to maintain proper airflow and contain heat and lint. Replace if you notice reduced drying performance or air leaks. Confirm fit.

The Duct Trap Housing is an OEM component specifically designed for GE laundry machines. It serves as the housing and base unit for the duct trap or lint trap that collects lint and debris during the drying cycle. The duct trap housing is designed to seamlessly integrate with the dryer vent and ducting system.

Causes of a bad duct trap housing include cracks or warping from heat exposure over time, damage due to impact or mishandling, or worn-out mounting components that secure it in place.  

Symptoms of a bad duct trap housing include:

• Excessive lint buildup inside the dryer indicating incomplete lint removal  
• Airflow issues such as longer dry times or wet clothes after a full cycle
• Venting problems like drafts or leaks at the vent connection
• Noise or vibration originating from the vent area

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Seals the gap between the drum and front panel to prevent air leaks and noise. Replace if worn, damaged, or causing squeaking sounds. Verify fit with your model.

Top bearing assembly supports and stabilizes the dryer drum for smooth rotation. Replace if drum wobbles or makes grinding noises. Verify fit with your model.

Illuminates your dryer drum for better visibility when loading and unloading clothes. Replace when burned out or flickering. Verify fit with your model.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Dryer bearing slides enable smooth drum rotation. Replace when hearing squeaking or rumbling sounds during cycles. Confirm fit with your model number.

Dryer drum felt top bearing provides smooth drum rotation and reduces friction. Replace when you hear squeaking or grinding noises during operation.

Wire connector for dryers. Installs in the wiring harness to create secure electrical connections. Replace if connector is damaged, melted, or corroded.

*** Note: The original seal is no longer available separately. Order complete duct assembly by model. ***

Elbow and nozzle assembly for dryers. Connects ductwork and directs airflow. Replace if cracked, broken, or missing to restore proper ventilation.

Plastic flat drive belt for dryers. Transmits motion between components. Replace if worn, cracked, broken, or slipping to restore smooth operation.

This harness top bearing assembly replaces a worn or damaged top bearing and its attached wiring harness, helping restore smooth drum support and reliable electrical connections for the washer's tub. Fits select GE top-load washers. What it does:

• Supports the washer tub at the top to reduce wobble and wear on the drum
• Houses the bearing surface for the tub to rotate smoothly
• Includes the attached wiring harness to maintain connections for sensors or components mounted at the top
• Commonly used when customers notice excessive vibration, noise, or intermittent electrical issues near the top of the washer

• One harness top bearing assembly (bearing with attached wiring harness) as shown

• Service requires access to the washer cabinet and top/tub assembly—disconnect power and water before starting
• Inspect surrounding suspension and seals; replace any damaged fasteners or clips during reassembly
• Handle bearings and electrical connectors carefully to avoid contamination or pin damage

Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.

Felt strip that seals your dryer's lint filter opening to prevent lint bypass and air leaks. Replace when worn, torn, or no longer creating a tight seal.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

This small mounting screw secures panels and trim on compatible GE appliances, restoring a solid, vibration-free fit. Use it to replace a missing, stripped, or damaged fastener and keep parts aligned and secure. What it does:

• Fastens panels, trim, or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Restores secure attachment when threads are stripped or worn
• Helps maintain proper alignment to prevent noise and component wear

• Use the correct screwdriver size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power or move the appliance to a safe position when accessing internal panels
• Consider a replacement clip or insert as recommended by the manufacturer

If your dryer won't start or the door won't latch securely, the door strike may be worn or broken. This part ensures proper door closure. Easy DIY fix.

Stainless steel #8 x 5/8" screw for dryer door and panel assembly. Replace missing, stripped, or corroded screws to secure components properly.

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Secures the door guide strip to your dryer frame, keeping the door aligned. Replace this nut if it's missing, stripped, or worn to restore proper fit.

Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.

Aligns and supports your dryer door for smooth closing and secure latching. Replace if cracked, broken, or missing to eliminate gaps and restore fit.

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

Y adapter for dryers. Connects ducts or hoses in split configurations. Replace if cracked, broken, or missing to ensure proper airflow routing.

Steam generator assembly for dryers with steam-refresh cycles. Installs inside cabinet to heat and release steam. Replace if cracked, leaking, or damaged.