Parts for Ge PTD90EBPT1DG: Front Panel Parts

The Lint Filter Assembly is an OEM replacement part for GE dryers. This component is designed to capture lint and other debris generated during the drying process, preventing it from accumulating in the dryer's exhaust system and posing a potential fire hazard.

Symptoms of needing to replace the lint filter assembly include:

• Decreased drying performance or efficiency
• Visible damage, deterioration, or clogging of the filter
• Difficulty in removing or reinstalling the filter assembly

Causes of a faulty lint filter assembly can include normal wear and tear over time, excessive lint buildup or blockage, or physical damage due to mishandling or improper cleaning.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

These duct trap slides replace the moving rails that let the dryer's duct trap assembly open and close smoothly, helping restore proper vent access and reduce rattling or binding. Designed to match OEM fit and function. What it does:

• Guides the dryer duct trap so the trap door opens and closes smoothly
• Helps prevent the trap from sticking, misaligning, or making noise
• Restores proper vent access for cleaning and maintenance
• Works with the duct trap assembly to maintain a secure fit

• Recommended for experienced DIYers; unplug appliance and move away from the wall before beginning
• Remove front access panel or lint trap assembly to reach trap slides
• Inspect surrounding clips and fasteners; replace any damaged hardware to ensure secure fit

This duct trap redirects and contains exhaust from the appliance's ventilation opening to help guide airflow and capture debris before it enters the main ductwork. It's a direct-replacement service part designed to restore proper vent routing and reduce buildup in the duct path. What it does:

• Funnels exhaust from the appliance outlet into the duct system for proper ventilation
• Helps prevent large debris and lint from entering the main duct run
• Restores correct vent alignment and sealing for efficient airflow
• Commonly replaced when damaged, cracked, or allowing exhaust leaks

• One duct trap

• Disconnect power to the appliance before starting any work; if gas is present, follow gas-safety shutoff procedures
• Access may require removing the rear/discharge panel or lowering the appliance; keep track of fasteners
• Inspect adjoining ductwork and seals; replace or reseal with appropriate high-temp duct tape when reinstalling
• Wear gloves and eye protection

The Lower Drum Felt seal is an OEM replacement part for GE dryers. The Lower drum felt seal is responsible for creating a seal between the drum and the front panel of the dryer.

This part fixes the following symptoms:

• Air leaking from the dryer drum
• Reduced dryer efficiency and increased energy costs
• Clothes becoming caught in the gap between the drum and front panel
• Potential damage or snags to clothes or the dryer

Causes of a bad Lower Drum Felt Seal can range from normal wear and tear, which degrades the felt material over time, to excessive load sizes that strain the drum and seal. Additionally, over time, the seal can become compressed or damaged, leading to a less effective seal and the potential for heat loss and inefficiency in the drying process.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Front Drum Support is an OEM part for GE dryers. This component provides critical support to the front of the dryer drum, allowing it to rotate smoothly and maintain proper alignment during the drying cycle. The support does not include bearing slides

A failing drum support can cause the drum to misalign or make unusual noises, leading to potential damage to other components and less effective drying performance.

Symptoms of a bad front drum support include:

• Unusual noises such as squeaking or grinding during operation
• The drum not rotating smoothly or being out of alignment
• Increased wear on the drum or other internal components
• Clothes taking longer to dry or coming out damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Felt Top Bearing is an OEM part for GE dryers. It provides a smooth surface for the drum to rotate on, reducing friction and wear on the drum and other components.  

Causes of a bad felt top bearing can include prolonged use, exposure to high temperatures, or the accumulation of lint and debris.  

Symptoms of a bad felt top bearing include:

• A squeaking or grinding noise during the drying cycle
• Increased friction, causing the drum to turn less smoothly
• Visible wear or damage to the felt material
• Clothes snagging or being damaged inside the dryer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This gasket is a direct-fit door seal that restores the appliance's airtight closure to help maintain proper temperature and reduce energy loss. It replaces worn, torn, or compressed seals to improve performance. What it does:

• Creates an airtight seal around the door to keep conditioned air inside
• Helps prevent warm air intrusion, frost buildup, and excess cycling
• Reduces condensation and keeps food at intended temperatures
• Restores efficient operation when the original seal is cracked or deformed

• One door gasket

• High-level replacement: remove the old gasket, clean the gasket channel, then align and press the new gasket into the channel until fully seated
• Inspect gasket mounting tabs or retainer channels and reuse any clips or screws if applicable
• Work with the appliance powered off; unplug or switch off power for safety where appropriate
• If the gasket feels stiff, warm it gently for easier fitting; avoid sharp tools that could damage the new gasket

The Bearing Slide Assembly is an OEM component for GE electric clothes dryers. As an integral part of the dryer tumbler system, this assembly includes the bearing slides that allow smooth rotation of the tumbler drum during drying cycles. 

Symptoms of faulty bearing slides include:

• Abnormal vibrations or shaking of the dryer cabinet 
• Noisy operation that gets louder over time
• Rubbing or grinding sounds coming from inside the machine
• Reduced tumbler movement or inability to manually turn the drum

Causes involve general wear of plastic bearing surfaces from years of drum rotation as well as potential damage or misalignment from excess stress on the slides.

This GE OEM replacement helps maintain balanced tumbler movement. Compatible with Hotpoint, RCA, and some Kenmore dryers using the bearing slide assembly design.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Front Drum Support Assembly is an OEM part for GE dryers. It supports the front of the dryer drum, allowing it to rotate smoothly during the drying cycle.

Causes of a bad front drum support assembly can include wear and tear from regular use, damage from foreign objects entering the drum, or deterioration of the support glides or rollers over time.

Symptoms of a bad front drum support assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The drum not rotating properly or getting stuck
• Visible wear on the support glides or rollers

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lint Screen Housing Seal is an OEM part for GE dryers. This seal is designed to fit around the housing of the lint screen, ensuring a tight seal that prevents lint and small particles from bypassing the filter and entering the dryer's internal components. This seal measures approximately 36” long.

Symptoms of a failing lint screen housing seal include:

• Increased accumulation of lint inside the dryer cabinet
• Decreased drying efficiency, requiring longer cycles to dry clothes
• Visible wear or gaps in the seal

Causes of wear or failure of the lint screen housing seal often include regular use, which can stretch or tear the material, exposure to high temperatures which can degrade the rubber or foam, and improper installation which can lead to a poor fit.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This LED light assembly provides interior illumination for compatible refrigerators, restoring clear, energy-efficient light inside the fresh-food compartment. Replaces a failed or dim interior lamp to help you see food and shelves more easily. What it does:

• Replaces a burned-out or nonworking interior LED light assembly
• Restores steady, bright illumination when the door is open
• Helps eliminate flickering, dimming, or intermittent lighting issues
• Designed to fit the refrigerator's existing light housing and connector

• Disconnect power to the appliance before starting any work to avoid shock.
• Handle the LED module and connector carefully to avoid damage.
• Typically a direct plug-in replacement; follow the refrigerator's service manual for removal and installation.

This door switch is an OEM replacement part for GE dryers. This switch is designed to promptly end the dryer cycle when the door is opened. The switch comes equipped with a metal lever arm and plunger that can be depressed to activate the switch.

Causes of a bad door switch can include normal wear over time from repetitive open/close cycles. Exposure to moisture, food drips or cleaning chemicals may also contribute to switch failure. 

Symptoms of a bad door switch are:

• The oven will not start a bake cycle with the door securely latched  
• Error codes displayed related to the door being open
• Inconsistent or unreliable door closure sensing  
• Failure to function properly after cleaning or moisture exposure

This OEM part is also compatible with ranges sold under Hotpoint and RCA brands and some Kenmore models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

The HARNESS SENSOR ASSEMBLY is an OEM part for GE electric dryers. It is a comprehensive harness assembly that includes sensors to monitor temperature and moisture levels during drying cycles. These sensors relay crucial data to the dryer control board allowing for optimized cycle times and prevention of over-drying.

Symptoms of a bad harness sensor assembly include:

• Dryer cycles not running for full expected time durations   
• Clothes continually coming out damp rather than fully dried
• Dryer failing to advance through programmed cycles properly
• Error codes or faults displayed on the control panel 

Causes can arise from damaged or loose wiring connections, faulty sensors that provide inaccurate readings, or general failure over time due to environmental exposure.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

This steam kit is the OEM steam generator assembly that supplies steam for steam-refresh and wrinkle-care cycles. It restores the appliance's ability to produce steam for improved fabric care and odor removal. What it does

• Heats and releases water as steam into the drum during steam cycles to help relax wrinkles and freshen clothes.
• Addresses weak or no-steam symptoms when the dryer runs steam cycles but garments remain untreated.
• Works with the appliance's control system to deliver steam only during designated cycle phases.
• Helps reduce the need for ironing by loosening fabric fibers during the cycle.

• One steam generator assembly (steam kit) as shown.

• Disconnect power before starting any repair to avoid shock or flooding.
• Suitable for technicians or experienced DIYers; follow the appliance service manual for disassembly and routing of water/steam lines.
• Inspect and replace any brittle or cracked tubing and seals to prevent leaks; test for proper steam delivery after installation.
• Do not operate the dryer with missing or damaged panels; ensure all connectors are secure.

The Shoe Drying Rack is an OEM accessory component specifically designed for select GE dryers. As an added feature, this rack provides a convenient way to dry shoes along with regular laundry items. It allows wet shoes to be tumbled gently while being fully ventilated to dry effectively.

Symptoms of a bad shoe drying rack include:

• Broken or cracked rack supports that collapse the structure
• Missing hooks or attachment points to secure the rack in place  
• Rust, corrosion, or other damage that compromises its functionality

Causes of a bad shoe drying rack can include normal wear and tear over extended use, exposure to excessive heat levels, or damage from overloading or improper handling.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.