Gaggenau Range / Cooktop / Oven Parts

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Door won't lock or difficult to open during self-clean? This oven door latch assembly secures the door and reports lock status to the control board.

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

This light bu is a genuine Bosch part, sold individually. This light bu can be used as a replacement part for a gas range. This part illuminates the inside of the oven so that its interior can be seen while the appliance is in operation. This allows the user to see the interior without opening the door or visually inspecting the oven from the inside.A light bu will often be subject for replacement at some point in the lifespan of a gas range. This will most likely be due to a light bu losing power over time, but damage can also occur that will necessitate replacement, including cracks, chips, and punctures that can shatter a light bu immediately. If this is the case, the light bu should be removed and replaced with this genuine OEM replacement part. The replacement process will require no special tools. Simply screw the light bu into place.This is an OEM part sourced directly from the manufacturer. It is sold individually. This light bu is compatible with the following appliance brands: Bosch and Gaggenau.

This thermocouple monitors the burner flame and works with the safety valve. It allows gas flow only while a flame is present and lets the valve close when no flame is detected, helping restore dependable burner operation.

• Senses burner flame heat and sends a small millivolt signal to the safety valve
• Works with the flame-failure safety system to maintain or cut gas flow based on flame presence
• Common symptoms can include: burner lights but goes out when the knob is released; needing to hold the knob down unusually long to keep the burner lit

• Disconnect power and shut off gas before servicing
• Allow the unit to cool; remove grates/caps to access the sensor tip and route the lead to the valve connection as originally installed
• Do not kink or sharply bend the lead; position the tip within the burner's flame envelope
• After reassembly, restore gas/power and test burner operation

Fix a microwave door that won't pop open when you press the button. This door release lever restores smooth latching action for easy everyday use.

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

This door hinge provides the pivot point that lets the appliance door open smoothly and close flush. Replacing a worn or bent hinge restores proper alignment and sealing for safe, reliable door operation.

• Provides the pivot point that guides door opening and closing
• Helps keep the door square to the cabinet for a consistent seal
• Wear or damage can cause sagging, binding, gaps, or a door that won't close flush
• Restores smooth movement and proper door alignment

• Disconnect power before servicing; also shut off gas or water
• Support the door during removal to prevent damage or injury
• Transfer any mounting screws/brackets from the old hinge to the new one
• After installation, verify door alignment and gasket contact; adjust as needed

This small spring fits behind the control knob to provide tension and a positive, secure feel. Replace it to restore proper knob height and a snug fit when the knob feels loose, wobbly, or won't stay seated.

• Provides spring tension between the knob and control shaft for proper engagement
• Helps keep the knob centered and at the correct height on the control panel
• Restores firm, consistent knob feel during operation
• Common symptoms: loose or wobbly knob, knob doesn't stay seated or sits unevenly

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the knob straight off the shaft; note the spring's position/orientation
• Remove the old spring and seat the new spring on the shaft or in the knob recess
• Reinstall the knob and check for smooth operation; do not force the knob onto the shaft

Replacement energy regulator that helps control power delivery to the appliance's heating and control circuits, restoring stable performance and addressing power-related faults. Installs in-line with the factory wiring to replace a failed regulator. What it does:

• Regulates power to heating and control components to maintain expected operation.
• Can resolve symptoms such as inconsistent heating, intermittent operation, or unexpected shutdowns.
• Prevents erratic behavior caused by a failing power-control component.
• Works as a direct replacement for the factory energy regulator to restore proper function.

• Disconnect all power before beginning service to avoid shock or injury.
• Use basic hand tools; inspect wiring and connectors for damage and replace any compromised parts.
• Refer to the appliance service manual or OEM instructions for specific removal and installation steps.

Flame-sensing thermocouple for generator pilot assemblies. Replace if cracked, corroded, or failing to detect flame properly. Installs at pilot light.

Spring for knob that restores proper tension and return action to a control knob, helping knobs operate smoothly and stay in position. Use this small replacement when a knob feels loose, won't center, or won't return. What it does:

• Provides tension and return action for a control knob so it centers and responds correctly.
• Replaces worn or broken knob springs that cause loose, wobbly, or non-returning knobs.
• Works as the mechanical spring behind the knob's rotation and detent action.
• Small, straightforward part used wherever a control knob needs restored tension.

• Disconnect power to the appliance (unplug or switch off circuit breaker) before servicing.
• Remove the knob and any bezels per the appliance's service instructions to access the spring.
• Handle small parts carefully; keep orientation noted for correct reassembly.

This burner lid is the top cover for a slim two-piece gas cooktop burner, protecting the burner head and helping direct flame. It restores proper burner appearance and helps maintain even ignition and heat distribution. What it does

• Covers the burner head to protect internal parts from spills and debris
• Helps direct gas flow for a consistent flame pattern during cooking
• Can reduce ignition issues caused by food or liquid obstruction on the burner head
• Restores the cooktop's finished look where the original lid is cracked, warped, or missing

• One burner lid (slim 2-piece style)

• Turn off the appliance and gas supply (or unplug) before servicing; allow all parts to cool completely
• Lift off the existing lid and position the replacement so it seats securely on the burner base
• Do not force or overtighten—ensure proper alignment to avoid damaging the burner head

This metal mesh grease filter captures airborne grease and large particles from range hood airflow to help keep the vent and exhaust path cleaner and reduce greasy buildup on internal components. What it does:

• Traps cooking grease and large particulates before they reach the blower or ducting
• Helps reduce greasy residue and buildup on internal hood surfaces
• Can improve airflow consistency when the filter is clean
• Common symptom: heavy visible grease, dark film on the filter, or smoke/odors not clearing effectively

• Turn off power to the range hood or vent before servicing
• Remove the old filter per the hood's access method (clips, slides, or screws), then insert the replacement securely
• Clean or replace regularly per the appliance owner's manual; do not operate with a damaged filter

This door latch assembly secures the door closed and signals the control that it's safely shut, allowing cycles to start and run. Replacing a worn latch restores a reliable safety interlock and consistent operation.

• Secures the door and engages the safety interlock so the appliance can operate
• Sends a "door closed" signal to the control
• Common symptoms: door won't latch or stay closed; unit won't start or pauses as if the door is open; intermittent operation when the door is bumped; visible wear or damage to the latch
• Helps prevent nuisance "door open" indications

• Disconnect power before servicing
• Access the latch from the door area; remove inner panel or trim as required by your model
• Note wire positions, transfer connectors, and mount the new latch in the same orientation
• Test door closure before reassembly

Seals the heating element opening to maintain proper heat and prevent leaks. Replace when worn or damaged to restore efficient operation. Confirm fit.