Gaggenau Range / Cooktop / Oven Parts

This is a foam sealing strip that creates an airtight seal between panels or the door area of the microwave. It helps prevent heat loss, air leaks, and moisture intrusion. Replace this strip if it appears compressed, crumbling, or if you notice gaps, rattling noises, or reduced heating efficiency.

This is a rubber or silicone sealing grommet used to create an airtight seal around openings or connections within the microwave. It helps prevent moisture, heat, and air from escaping or entering where components pass through panels. Replace this part if you notice steam leaking from unusual spots, rattling noises near sealed areas, or visible cracking and deterioration of the original seal.

This door latch assembly secures the door closed and signals the control that it's safely shut, allowing cycles to start and run. Replacing a worn latch restores a reliable safety interlock and consistent operation.

• Secures the door and engages the safety interlock so the appliance can operate
• Sends a "door closed" signal to the control
• Common symptoms: door won't latch or stay closed; unit won't start or pauses as if the door is open; intermittent operation when the door is bumped; visible wear or damage to the latch
• Helps prevent nuisance "door open" indications

• Disconnect power before servicing
• Access the latch from the door area; remove inner panel or trim as required by your model
• Note wire positions, transfer connectors, and mount the new latch in the same orientation
• Test door closure before reassembly

This grease filter captures airborne grease from oven ventilation to help reduce buildup and keep internal parts cleaner. It fits flush in the oven vent and is a replaceable maintenance part. What it does:

• Traps cooking grease and airborne oils before they reach fan and ducting
• Helps reduce grease deposits that can cause smoke or odors during cooking
• Supports proper airflow by preventing clogging of the vent path
• Visible grease or darkened filter surface are common signs it needs replacement

• Disconnect power to the appliance before removing or installing the filter
• Slide or snap the filter into the vent slot per the appliance's filter-retention method
• Handle carefully to avoid sharp sheet-metal edges; wear gloves if needed
• Clean surrounding area and check the vent for heavy buildup when replacing

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

Replacement burner head for gas cooktops. Restores even flame distribution when original is corroded, damaged, or worn. Direct-fit part for VG models.

This burner lid is the top cap for a three-piece gas cooktop burner. It protects the burner head and helps shape the flame for more even heating and stable performance during cooking. What it does:

• Covers the burner head and directs flame for consistent heat distribution
• Helps maintain stable flame pattern and reliable ignition behavior
• Replaces lids that are cracked, chipped, warped, or corroded
• Can reduce uneven cooking or flickering/unstable flames caused by damaged lids

• Turn off gas supply and power to the appliance and allow all parts to cool fully before servicing
• Remove the old lid and seat the new lid squarely on the burner head; ensure it does not obstruct the igniter or burner ports
• Inspect surrounding burner components for damage; replace any damaged rings, caps, or gaskets as needed

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This burner lid is the replacement top cover for a VG 230/330 gas burner assembly, restoring proper burner protection and heat distribution for reliable cooktop operation. Designed to fit the OEM burner geometry and surface finish. What it does:

• Covers and protects the burner cap and inner components from spills and debris.
• Helps channel flame and heat for more even cooking performance.
• Reduces the chance of food or liquids reaching ignition parts that can cause burner issues.
• Common symptom: cracked, warped, or missing lids that allow uneven flames or visible damage.

• Turn off gas and power to the appliance and allow all surfaces to cool completely before servicing.
• Remove burner grates and caps as needed; lift out the old lid and seat the new lid in the burner recess.
• Inspect surrounding components (cap, electrode/igniter) for damage while installing.

Spring for knob that restores proper tension and return action to a control knob, helping knobs operate smoothly and stay in position. Use this small replacement when a knob feels loose, won't center, or won't return. What it does:

• Provides tension and return action for a control knob so it centers and responds correctly.
• Replaces worn or broken knob springs that cause loose, wobbly, or non-returning knobs.
• Works as the mechanical spring behind the knob's rotation and detent action.
• Small, straightforward part used wherever a control knob needs restored tension.

• Disconnect power to the appliance (unplug or switch off circuit breaker) before servicing.
• Remove the knob and any bezels per the appliance's service instructions to access the spring.
• Handle small parts carefully; keep orientation noted for correct reassembly.