Parts for Ge JGP628CEJ1CC: 02 - Gas & Burner Parts

Natural gas orifice spud for cooktop burners. Installs at burner base to regulate gas flow. Replace if damaged, worn, or converting fuel type.

Natural gas orifice spud for cooktop burner assembly. Needed when converting from LP to natural gas or replacing damaged orifice threading.

Converting your cooktop from natural gas to liquid propane? This LP gas orifice spud enables proper fuel conversion for specific burner positions.

Liquid propane orifice spud for cooktop and range burners. Regulates gas flow for proper flame. Replace if damaged, worn, or converting from natural gas.

Replace worn felt pads that cushion your range door and prevent rattling or gaps. Essential when door closes unevenly or makes noise. Confirm fit with model.

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

What's included:

• 1 hold-down bracket

Install notes:

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

Secures the ignition electrode on gas range burners. Replace if burners won't spark, igniter clicks continuously, or clip is corroded or loose. Confirm fit with your model number.

Replace worn cooktop foam seal tape to prevent heat loss and ensure proper insulation. Essential for maintaining energy efficiency. Verify fit with your model.

Replace your cooktop's burner tube that delivers gas from the valve to the burner. Order this tube if yours is cracked, corroded, or misaligned.

Burner tube that connects gas valve to the burner assembly on your cooktop. Replace if cracked, corroded, or damaged to restore proper gas flow.

Burner tube for gas cooktops. Connects gas valve to burner head. Replace if cracked, corroded, or showing signs of gas leakage for safe operation.

Burner tube for gas cooktops. Connects gas valve to burner head. Replace if cracked, corroded, or damaged to restore proper gas flow to burner.

Gas pressure regulator for cooktops and ranges. Installs on the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.

Burner leaking gas or won't light? This gas valve controls fuel flow to your cooktop burners. Requires disassembly of burner bases and cooktop lift-off.

Fix burners that won't ignite or spark continuously. This spark module controls ignition for all surface burners. DIY repair in about 45 minutes.

Secures gas valve connections on your cooktop. Replace if loose, cracked, or causing gas leaks. Verify fit with your model number before ordering.

Right angle

This seal manifold is the molded gasket that seals the connection between the manifold and valve assembly, preventing leaks and ensuring proper flow. It restores a watertight/gas-tight seal where the manifold meets the control valves. What it does

• Seals the joint between the manifold and valve assembly to prevent fluid or gas leaks.
• Helps maintain correct pressure and flow through the manifold and valves.
• Addresses symptoms such as visible leaks, strong odors, or intermittent flow/operation around the manifold area.
• Restores reliable sealing after manifold or valve service or when the original seal is damaged.

• Before you start, disconnect power and shut off water or gas supply as applicable to the appliance.
• Replace only with the matching OEM part and ensure mating surfaces are clean and dry for a proper seal.
• Tighten manifold fasteners evenly to the manufacturer's guidance to avoid distortion (follow OEM torque/sequence if available).

Replacement power cord for cooktops. Connects your cooktop to the electrical outlet. Replace if cord is frayed, damaged, or missing for safe operation.

ST10-16 X 7/16"

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

Black. 8-18 AB HXW 3/8