Parts for Trimmer Plus 41AJXL-C902: General Assembly Parts

This is an accessory hanger that is intended for use with a variety of lawn and garden equipment. It attaches to equipment so the tool can be hung up for storage. The hanger can help to ensure that tools are easy to access in an out of the way space.The hanger that is currently on the machine could be damaged or could crack after a lot of use, and it might need to be replaced. It is an easy replacement and should only take a matter of minutes at most.This hanger can be used with trimmers, edgers, pruners, blowers, and cultivators from Ryobi, Troy-Bilt, MTD, and Cub Cadet. Each hanger is sold individually. Owners with multiple pieces of equipment will want to buy as many as needed. This is a genuine OEM part sourced from the manufacturer.

This lower boom assembly is a genuine MTD part, sold individually. This lower boom assembly can be used as a replacement part in a lawn mower or a lawn tractor. The purpose of the lower boom assembly in a lawn mower or a lawn tractor is to affix to the gearbox of the appliance.The lower boom assembly might need to be replaced at some point in the lifespan of a lawn mower or a lawn tractor. To facilitate the replacement, the operator must unscrew the screws within the upper and lower shaft, remove the malfunctioning or damaged boom assembly, separate the gearbox from the shaft, secure the gearbox to the new shaft, and then place the new boom assembly where the old boom assembly was. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This lower boom assembly is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, and Cub Cadet.

This screw and nuts set is a genuine MTD part, sold individually. This screw and nuts set can be used as a replacement part in a string trimmer. This set provides a variety of screws and nuts which serve as fastening components within the string trimmer.The screw and nuts set in a string trimmer might have to be ordered as a complete replacement part if one or more screws or nuts in the string trimmer has been lost, misplaced, or damaged. If this occurs, the screw and nuts set should be ordered as a genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This screw and nuts set is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Bolens, and Yard Man.

The flexible lower drive shaft is for use specifically with select models of trimmers. The drive shaft is used to rotate the cutting head on the line trimmer. If the owner notices that their cutting head is not rotating properly, it could be due to an issue with the drive shaft. If it is not replaced, it could reduce the effectiveness of the trimmer.Although the flexible lower drive shaft is made from high-quality materials, owners might find a need to replace it. It could become damaged due to wear and tear, for example. Owners should be sure to wear gloves to keep their hands safe during the replacement.The trimmer flexible lower drive shaft can work with certain machines from Craftsman and MTD. This is a genuine OEM replacement part that has been sourced from the manufacturer. It is sold individually.

This replacement part is a gearbox intended for use in grass trimmers. This is a genuine replacement part made by MTD. Gearboxes connect the main handle of the appliance to the rotating blade attachment. It is important that this part is secure as the blade cutter can be dangerous if loose.A new gearbox might be needed if the current one is broken or damaged in any way. It is not unusual for this part to require replacement after years of normal use as it's easy for the gearbox to become stripped down. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide or manual for the appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with grass trimmers made by MTD.

This is a genuine replacement screw designed for use in select MTD engines on lawn and garden equipment. Specifically, this is an anti-rotation screw, which is used to stop the drive shaft housing from turning inside of the main housing assembly. This screw is a small part that is subject to constant vibrations, pressure, and high temperatures. It can sometimes become worn or damaged as a result or even break off entirely, which would mean that the inner housing would no longer be held in place accordingly. If this screw is damaged or lost, it needs to be replaced with a genuine OEM replacement as soon as possible. This MTD anti-rotation screw is manufactured with high-quality materials and designed for use in select trimmers from MTD, RYOBI, Yard-Man, Troy-Bilt, Murray, Cub Cadet, Yard Machines, and Bolens. This replacement will require a screwdriver. Simply remove the damaged screw, if it is not already missing, from the clutch cover assembly, and then install the new screw. It should only take a few minutes to perform the replacement. Be sure to wear gloves to protect the hands. This screw is sold individually and does not include any additional parts or hardware.

This replacement part is a screw, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Screws are found in almost every different type of machinery and are essential to the overall performance of different devices. Screws are responsible for holding things in place and securing them tightly so that the machine can operate smoothly and efficiently. A new screw might be needed if the current one is damaged or missing. It is possible for screws to be stripped over time and can become stuck in place. In this case, pliers might be needed to remove the faulty screw. Otherwise, this repair should be fairly simple and only require a screwdriver. Be sure the machine is powered down before replacing this part. This specific screw is sold individually and is a genuine OEM replacement part. Be sure to purchase the correct amount as many devices require more than one.

This cutting head holds the line that trims weeds and grass on several specific handheld gasoline trimmers. It is covered with a thick plastic cap that is bumped against the ground so that line can be released from the spool. The plastic bump head can endure an indefinite number of bumps against the ground. The cutting head not only experiences all the same bumps but also turns at 12,000 and must stop and start rapidly. As a result, after continual use, the cutting head sometimes requires replacement. There are several clues to suggest that a cutting head needs to be replaced. Most often, the bump function ceases to work or works sporadically. To replace the cutting head, press the slots in the bump housing to release the lower part of the housing. After removing the bump head, a ratchet is needed to remove the old head. Reverse the process to install the new cutting head. If a user must replace a cutting head, it is essential that it be replaced with a genuine OEM part made by Cub Cadet such as this one. This replacement cutting head is guaranteed to perfectly match the specifications of the original part it is replacing.

This gearbox spacer is a genuine MTD part, sold individually. This gearbox spacer can be used as a replacement part in a string trimmer. The purpose of the gearbox spacer in a string trimmer is to serve as a fastening component within the infrastructure of the gearbox.The gearbox spacer might have to be replaced at some point within the typical lifespan of a string trimmer due to the fact that the spacer is a small component that can be easily lost or misplaced; the gearbox spacer could also be stripped over time from general wear and tear with long-term use, in which case the gearbox spacer should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that requires simply installing the new spacer in its previous position.This component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This gearbox spacer is compatible with the following outdoor appliance brands: MTD and Cub Cadet.

This is a replacement string trimmer head that is used for a range of makes and models of trimmer. The head, sometimes called a cap, is placed on the bottom of the cutting head assembly. The glide cap is simple, but it serves an important function. It helps to keep the head from contacting the ground, so it is not damaged. The string trimmer head often comes into contact with the ground, roots, concrete, and other materials. Therefore, it can become damaged. It might crack or it could simply start to suffer from normal wear and tear after a lot of use. When this happens, owners should always replace the part sooner rather than later. If it is broken or not functioning properly, it could cause problems with the other elements in the trimmer. The replacement is simple and should not take users more than a few minutes to complete. The replacement string trimmer head is a genuine OEM part and it is sold individually. This part is for use only with string trimmers and is compatible with certain models from MTD and Cub Cadet.

Trimmers have a shield assembly that protects the user from flying debris while the trimmer string is in operation. If this assembly cracks or falls off, the trimmer should not be operated until a new on is installed. Over time, the sun's heat may cause the plastic to crack, ultimately leading to the shield falling off. Safety is an important factor when operating lawn and garden equipment. Routine inspections of all equipment will reveal if any of the safety components of the machines are broken or missing.This shield assembly is an authentic OEM replacement part sourced directly from the manufacturer. Before installing this part, make sure the spark plug is removed and wear safety gloves. After removing the damaged shield, this shield should be installed using the screws from the one taken off the trimmer. This shield assembly is a black molded plastic part that is sold individually. It does not come with screws. It is designed for use with trimmers manufactured by Troy-Bilt and Craftsman.