Gibson Freezer Bracket & Flange
Genuine Frigidaire part
By: Frigidaire
Part Number: 5308000110
This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.
- Secures the defrost heater to the evaporator for proper contact and heat transfer
- Promotes complete, even defrosting across the evaporator coil
- Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
- Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator
Includes: Aluminum strap
- Disconnect power and allow ice to melt before accessing the evaporator
- Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
- Position the heater per your model's parts diagram and tighten the strap for firm, even contact
- Verify wiring is routed clear of the fan and moving parts before reassembly
Do-It-Yourself Stories from Customers like You
Refrigerator not cooling freezer ok Don L. • Peachtree City , GA • March 12, 2019
Removed the freezer shelves and back panel, evaporator coils were frozen with ice. Defrosted coil and removed defrost heater connectors, measured no continuity in the heater and ordered a replacement. Also discovered the aluminum retention strap was broken and the heater had slipped down in it's position, ordered and replacement strap. Re-installed new heater and strap per the video instructions, repair complete. Most difficult steps were drilling out the drain pan rivet and re-threading...
Read more
More
$50.78
- Compare At:
-
$60.43
- You Save:
-
$9.65
Genuine Frigidaire part
By: Frigidaire
Part Number: 08016580
$11.46
- Compare At:
-
$13.64
- You Save:
-
$2.18
Out Of Stock
Usually ships within 4 - 14 days
Genuine Frigidaire part
By: Frigidaire
Part Number: 216394050
This mounting bracket secures internal components and panels to restore proper alignment and reduce vibration. It provides a direct replacement for worn or damaged support hardware so assemblies stay firmly in place. What it does:
- Secures appliance panels or internal components to the cabinet or frame
- Keeps parts aligned to prevent rattling, vibration, or movement during operation
- Restores proper fit where a bent, broken, or missing bracket causes loose assemblies
- Helps maintain safe, stable operation by holding parts in their designed position
What's included:
Install notes:
- Designed to replace the factory bracket in the same mounting location; verify fit before installation
- Use appropriate fasteners and torque to avoid striping or damage to mounting points
- Disconnect power and empty unit if needed before accessing internal areas
Do-It-Yourself Stories from Customers like You
Was freezing up with ice, needed new fan and defrost switch Andrew S. • Derry , PA • September 22, 2020
I replaced the fan and switch for defrosting on the coil.
Read more
More
$15.95
- Compare At:
-
$18.82
- You Save:
-
$2.87
Out Of Stock
Usually ships within 4 - 14 days
Genuine Frigidaire part
By: Frigidaire
Part Number: 08016369
This mounting bracket secures the refrigerator/freezer alarm assembly, keeping the alarm in the correct position so alerts are audible and components stay stable. A simple replacement that helps restore reliable alarm operation. What it does
- Holds the alarm module or buzzer assembly in place inside the appliance chassis
- Prevents vibration or movement that can mute or misalign the alarm
- Commonly replaced when alarm is loose, rattling, or not properly secured
- Works with the alarm/buzzer housing to ensure audible temperature or door alerts
What's included
- Mounting bracket for alarm assembly
Install notes
- Disconnect power to the appliance before starting any repair to avoid shock or injury
- Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners removed from the appliance
- Match the bracket orientation to the alarm housing and secure all mounting screws snugly—do not overtighten
More
$10.50
- Compare At:
-
$10.73
- You Save:
-
$0.23
Out Of Stock
Usually ships within 4 - 14 days
Genuine Frigidaire part
By: Frigidaire
Part Number: 216926601
$6.36
- Compare At:
-
$7.00
- You Save:
-
$0.64
Out Of Stock
Usually ships within 4 - 14 days
Gibson freezer bracket or flange replacement parts are vital for keeping your freezer in optimal condition. These components ensure stability and functionality, making sure everything stays in place and operates smoothly. Whether you have a robust Gibson deep freezer or a compact unit, these parts are crucial for maintaining your appliance's performance.
Freezers are essential in any kitchen, preserving food and keeping perishables fresh for long periods. Gibson freezer parts, especially brackets and flanges, support shelves, secure the door, and ensure the structure remains solid. Using high-quality OEM replacement parts guarantees a perfect fit and reliable function, giving you peace of mind.
When looking to enhance or restore your freezer's performance, consider the value of Gibson freezer bracket or flange replacement parts. Their availability and assured quality keep your freezer running efficiently, ensuring the longevity and reliability of your appliance.
More