Parts for Ge AJCQ09DCEL2: 01 - Grille & Chassis Parts

This orifice meters gas flow to an oven burner, helping the appliance produce the correct flame for baking or broiling. Replaces a worn or clogged orifice to restore consistent burner performance. What it does:

• Controls the gas jet size to regulate burner flame size and heat output
• Helps correct symptoms like weak or uneven flame, slow oven heat-up, or burner that won't stay lit
• Prevents improper fuel-air mixture caused by a damaged or clogged orifice
• Used where precise gas flow is required for safe, efficient oven operation

• One orifice

• Shut off gas supply and unplug the appliance before servicing
• Use appropriate wrenches and avoid over-tightening to prevent damage
• Confirm correct orifice type for your fuel (natural gas vs. LP) before installation

This swing louver directs and balances airflow inside the refrigerator to help maintain even temperatures in the fresh-food compartment. It replaces a damaged or broken louver to restore adjustable airflow and proper venting. What it does

• Directs cooled air from the evaporator/fan into the fresh-food area
• Allows adjustable swing motion to spread air evenly across shelves
• Common fix for broken, cracked, or stuck louvers that limit airflow
• Helps reduce localized warm or cold spots caused by blocked vents

• One swing louver assembly

• Disconnect power to the appliance before beginning work
• Remove shelves or drawers as needed for access; handle plastic parts carefully
• Most installations snap into or slide onto the vent housing—do not force; verify alignment of tabs
• If clips are broken, replace clips or adjacent housing as needed for secure fit

This nut with attached washer is a small securing fastener used to clamp appliance parts and prevent loosening. It provides a low-profile, integrated washer bearing surface for a reliable hold. What it does:

• Secures panels, brackets, or components to prevent movement and rattling
• Maintains clamping force where an integrated washer is needed
• Helps keep electrical and mechanical connections stable
• Common symptom: loose or vibrating parts, squeaks, or components that shift during use

• One nut with attached washer

• Disconnect power and water before servicing
• Use the correct socket or wrench to avoid rounding the nut
• Tighten to snug fit — avoid overtightening which can strip threads or damage parts
• If replacing a rusted or damaged fastener, inspect mating threads and replace as needed

This flat washer provides a secure, even load distribution for a fastener on the appliance, helping maintain proper assembly and reduce loosening or wear. Use it to replace a damaged or missing washer during repairs. What it does:

• Sits under a nut or bolt to spread load and protect the appliance surface
• Helps prevent fasteners from loosening due to vibration
• Restores proper spacing and alignment for connected parts
• Commonly replaced when you see corrosion, cracking, or a loose connection

• One flat washer

• Disconnect power and turn off water supply before starting any repair
• Tighten fasteners to a snug fit—avoid over-tightening which can crush the washer
• If adjacent parts show damage or corrosion, inspect and replace as needed

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

This front panel is the replacement console face trim that restores the appliance's appearance and provides the mounting surface for the control components. It keeps controls aligned and gives a finished look to the unit. What it does:

• Replaces damaged, cracked, or faded front/console trim to restore appearance
• Provides the proper mounting and alignment for switches, buttons, and display components
• Helps protect internal controls from debris and accidental contact
• Can resolve cosmetic issues and intermittent control engagement caused by a warped or broken face panel

• One front panel as shown

• Disconnect power before starting any repair to avoid shock or injury
• Remove any knobs, trim pieces, and mounting screws to access and replace the panel
• Handle with care to avoid scratching the finished surface during installation
• Verify proper seating and secure fasteners before reassembly

This louver holder secures a vent louver or grille in place, restoring proper alignment and preventing rattling or detachment. It's a direct-fit replacement that helps maintain correct airflow direction and trim appearance. What it does:

• Secures the vent louver/grille to the appliance housing so the louver stays aligned
• Prevents rattling, vibration noise, and loose trim edges
• Helps maintain intended airflow path from the vent or exhaust area
• Replaces a cracked, broken, or missing louver mounting point

• One louver holder

• Disconnect power to the appliance before starting any work
• Remove the outer trim or grille to access the old holder (retain fasteners)
• Transfer or fasten the louver into the new holder, then reassemble trim
• If fasteners are corroded or damaged, replace with OEM-specified hardware

This louver link connects the vent louver or air damper to its actuator, restoring proper louver movement and airflow control. It's a direct-fit replacement used where the linkage has worn, broken, or come loose. What it does:

• Transfers motion from the actuator to the louver/damper so vents open and close properly
• Helps restore normal airflow and venting when louvers stick or droop
• Stops noisy or loose louver movement caused by a broken or bent linkage
• Keeps the louver aligned for even vent operation

• One louver link

• Disconnect power to the appliance before beginning repairs
• Access may require removing the grille, vent cover, or control access panel
• Inspect mating pins and actuator for damage; replace other worn parts as needed
• Tighten fasteners to secure the link but avoid over-torquing plastic components

A small metal notch spring that secures the oven/range door hinge in set positions so the door stays open or closed as intended. Replaces a worn or missing spring to restore proper hinge engagement and door positioning. What it does:

• Fits onto the hinge assembly and engages hinge notches to hold the door at set angles.
• Prevents the door from falling shut unexpectedly or failing to stay open.
• Reduces loose or jerky door movement caused by a weakened spring.
• Helps eliminate grinding or popping noises from hinge area when opening or closing.

• One notch spring.

• Disconnect power to the appliance before starting any repair.
• This small spring is installed on the hinge/notch area; some disassembly of the door or hinge may be required.
• Use caution around sharp edges and pinch points; keep fingers clear of tensioned springs.

This ratchet wheel is the replacement gear that engages a control drive to advance a unit's cycle. It restores proper mechanical engagement so the appliance can move reliably through its programmed steps. What it does:

• Engages with the drive/timing mechanism to advance and hold cycle positions
• Prevents backward rotation so settings stay in place between steps
• Helps restore normal cycle advancement when a worn gear causes skipped or stuck cycles
• Common symptom: cycles won't advance or the timer/control won't move smoothly

• Disconnect power before beginning any service to avoid shock or injury
• Access typically requires removing the control panel or relevant housing; keep track of screws and small parts
• Inspect mating gears and shafts for wear; replace damaged components to prevent repeat failure

This front panel is the replacement console face trim that restores the appliance's appearance and provides the mounting surface for the control components. It keeps controls aligned and gives a finished look to the unit. What it does:

• Replaces damaged, cracked, or faded front/console trim to restore appearance
• Provides the proper mounting and alignment for switches, buttons, and display components
• Helps protect internal controls from debris and accidental contact
• Can resolve cosmetic issues and intermittent control engagement caused by a warped or broken face panel

• One front panel as shown

• Disconnect power before starting any repair to avoid shock or injury
• Remove any knobs, trim pieces, and mounting screws to access and replace the panel
• Handle with care to avoid scratching the finished surface during installation
• Verify proper seating and secure fasteners before reassembly

The Air Filter is an OEM part for GE air conditioners. This filter is essential for trapping dust, pollen, and other airborne particles, ensuring that the air circulated within your space is clean and free from contaminants.

A clogged air filter can reduce airflow, causing the air conditioner to work harder and less efficiently. It can also lead to poorer air quality and increased wear on the unit's components.

Symptoms of a bad air filter include:

• Reduced airflow from the vents
• Decreased cooling efficiency
• Unpleasant odors coming from the air conditioner
• Increased dust in the air

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.