General Electric Room Air Conditioner Parts

The Air Filter is an OEM replacement part for GE refrigerators. This component plays a crucial role in maintaining air quality and freshness within the refrigerator compartment by trapping odors, pollutants, and airborne particles. It measures about 14-1/2 inches wide by 10 inches high.

Symptoms that may indicate the need to replace the air filter include:

•  Persistent unpleasant odors within the refrigerator
• Reduced air circulation or airflow
• Visible discoloration or clogging of the filter material

Causes of a faulty air filter can include normal wear and tear over time, accumulation of excessive debris or contaminants, or exposure to high humidity or moisture levels.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

The Air Filter is an OEM part for GE air conditioning units. It plays a role in filtering out airborne particles, dust, and other contaminants, ensuring clean and healthy air circulation within your home or workspace. The filter measures approximately 18.5 inches x 10 inches.

Symptoms of a dirty or clogged air filter:

• Reduced airflow from the vents
• Increased energy consumption and higher utility bills
• Unpleasant odors from the air conditioning unit
• Visible dirt buildup on the filter surface

Causes of a bad air filter can include normal wear and tear over time, exposure to excessive dust or pollutants, or inadequate maintenance and replacement schedules.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore air conditioning models. 

The Control Knob Assembly is an OEM part for GE air conditioners. This assembly allows users to adjust settings such as temperature, fan speed, and operational modes, providing precise control over the unit's performance.

Causes of a bad control knob assembly can include wear and tear from frequent use, accidental breakage, or internal component failure.

Symptoms of a bad Control Knob Assembly include:

• Difficulty turning or adjusting the knob
• The knob becoming loose or falling off
• Inconsistent or unresponsive changes in settings
• Visible cracks or damage to the knob

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This curtain assembly is the extendable side panel for a window air conditioner. It fills the gap between the A/C cabinet and window frame to restore a secure fit and help block drafts, moisture, and debris.

• Extends to close the side opening between the unit and the window jamb
• Helps reduce unwanted airflow, dust, moisture, and insects around the A/C
• Aids in maintaining a stable, properly aligned window installation
• Common symptoms: cracked or torn panel, brittleness, missing panel, visible light or air leaks at the sides

• Disconnect power and support the A/C so it cannot shift or fall while servicing
• Remove the damaged panel and retain any screws or mounting clips for reuse
• Slide the new curtain into the cabinet tracks and secure it to the window frame per your model's instructions
• Match orientation to the original panel and ensure smooth extension and an even seal before use

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

The Control Knob Assembly is an OEM part for GE air conditioners. This assembly includes the knobs that allow you to adjust settings such as temperature, fan speed, and mode. It is essential for the user interface of the air conditioner, providing an easy way to control and customize the cooling experience.

Causes of a bad control knob assembly can include wear and tear from frequent use, accidental damage, or exposure to high temperatures and UV light, which can cause the plastic to become brittle and crack.

Symptoms of a bad control knob assembly include:

• Knobs that are loose or difficult to turn
• Knobs that are cracked or broken
• Inability to change settings accurately
• Missing knobs

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the indoor fan motor for a room air conditioner. It drives the evaporator-side blower wheel to move cool air across the evaporator coil and into the room, restoring proper airflow and cooling performance.

• Powers the indoor blower wheel to circulate conditioned air
• Helps maintain correct airflow across the evaporator coil
• Common failure signs: fan won't run, slow or intermittent airflow, humming from motor, or overheating/shutdown
• May also be indicated by uneven cooling or the unit icing up due to poor airflow

• Unplug the unit and discharge capacitors before service
• Remove the front panel and access cover to reach the motor and blower
• Note wire positions; transfer mounting hardware and fan wheel as required
• Verify free-spinning blower and secure wiring before reassembly and test

Filter sub-assembly replaces the refrigerator's water-filter housing, holding the cartridge and directing water to the dispenser and ice maker. Restores secure cartridge seating and consistent water flow when the housing is damaged. What it does:

• Holds and seals the cartridge to help prevent leaks at the filter location.
• Directs filtered water to the dispenser and icemaker plumbing.
• Commonly replaced for leaks at the filter area, reduced water flow, or a loose/ill-fitting cartridge.
• Intended for cartridge-style refrigerator water-filter systems.

• Turn off the refrigerator water supply and relieve dispenser pressure before removing the old filter housing.
• Use basic hand tools; inspect and replace any worn O-rings or seals to ensure a proper seal.
• After installation, restore the water supply, check carefully for leaks, and run/flush water per refrigerator guidance.

This is the air filter assembly for select GE room air conditioners. It traps dust and lint before they reach the evaporator coil, helping maintain airflow and cooling performance.

• Captures airborne dust and lint to protect the coil and blower
• Helps maintain steady airflow and cooling efficiency
• Replace if cracked, warped, missing, or won't stay seated
• Common symptoms include reduced airflow and visible debris on the filter

• Unplug the unit before servicing
• Remove the front grille or filter access panel; slide the old filter out
• Install the new filter with airflow orientation matching the original
• Clean surrounding surfaces and reinstall grille before powering on

This replacement propeller is used on the outdoor fan of room air conditioners. It mounts to the condenser fan motor shaft to move air across the condenser coil, restoring heat rejection and airflow when the original blade is damaged or unbalanced. What it does:

• Moves outdoor air through the condenser coil to expel heat
• Helps address poor cooling caused by weak or no condenser airflow
• Replaces cracked, warped, or loose blades that cause vibration or scraping noises
• Symptom check: outdoor fan not spinning, weak airflow, rattling, or visible blade damage

• Includes: 1 propeller

• Disconnect power before servicing; wear gloves—blade edges can be sharp
• Note blade orientation and hub depth on the motor shaft before removal
• Remove the fastener/set screw and pull the old blade straight off; avoid bending coil fins
• Install the new blade in the same orientation, secure firmly, then test run

This protector heater is a small heating element used with the overload/thermal protector in the motor or compressor circuit. It provides calibrated warmth so the protector trips correctly under heavy load, helping prevent overheating and protecting the unit. What it does:

• Works with the overload/thermal protector to ensure proper trip timing
• Helps prevent overheating and potential damage to the motor/compressor
• Common signs include repeated clicking near the compressor area or frequent overload trips

• 1 protector heater

• Disconnect power and safely discharge the run capacitor before servicing
• Photograph or label wiring and component orientation for accurate reassembly
• Install in the same position/orientation as the original with secure, insulated connections and proper wire routing
• Inspect the overload, start device, and terminals; replace any burnt or loose connectors to prevent repeat failures

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

This air filter assembly traps dust and lint before they reach the evaporator coil, helping your room air conditioner maintain airflow and cooling performance. Replace clogged or damaged filters to protect components and keep cooling consistent. What it does:

• Screens intake air to help prevent debris from coating the evaporator coil and blower
• Helps sustain proper airflow and cooling performance
• A torn, missing, or heavily clogged filter can cause reduced air volume, longer run times, or uneven cooling
• Captures dust and lint that would otherwise accumulate inside the unit

• Includes: 1 air filter assembly

• Unplug the unit before servicing
• Open the front grille to access the filter; note the orientation of the old assembly
• Slide out the old filter and fully seat the new assembly in the same position
• Do not operate the unit without a filter installed

Keep your room air conditioner breathing easy with this replacement air filter. It captures dust and lint to help maintain airflow and cooling performance, while protecting the indoor coil from debris buildup.

• Screens return air to trap dust, lint, and debris before it reaches the evaporator coil
• Helps maintain proper airflow and consistent cooling
• Replace when torn, warped, missing, or heavily soiled
• Common symptoms of a bad/missing filter: weak airflow, poor cooling, longer run times, or frost on the coil

• Disconnect power before servicing
• Access the filter from the front grille or filter slot; slide out the old filter
• Clean the filter track/grille area; install the new filter fully seated and flat
• Operate the unit only with a filter installed to protect internal components

This protector heater provides a small, controlled heat source inside the appliance to keep sensitive components within range. It helps prevent condensation and nuisance trips so the unit operates reliably in cool or humid conditions.

• Provides low-watt heat around a protected area or thermostat
• Helps prevent moisture buildup and condensation
• Stabilizes temperature to reduce nuisance protector/thermal cutout trips
• Symptoms include intermittent operation, unexpected shutoffs, or visible condensation near controls

• Disconnect power before servicing and allow components to cool
• Note wire positions and routing on the original; move one connection at a time
• Mount in the original location and secure leads away from sharp edges, moving parts, and high-heat surfaces
• After installation, restore power and verify normal operation