Parts for Poulan PPB150E TYPE 2: Handle / Driveshaft / Shield Parts

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

This authentic OEM replacement on/off switch is a safety measure that manufacturers install to prevent the chainsaw or trimmer from starting before the operator is ready. It also allows the operator to stop their appliance at a moment's notice if they lose control of it. The on/off switch is located in or near the handle of the appliance and must be in the on position for the appliance to start. If hit to the off position, the appliance will immediately stop running. Switches can slowly wear out over time due to repeated use. When it wears out, the switch will no longer give the same amount of resistance and may be tripped more easily. This can be frustrating as it means that the operator would have to continually restart their appliance. To replace the switch, use a screwdriver to access the handle interior and detach the wiring from the old switch. Install the new part and reassemble. This switch is a high-quality replacement part for Craftsman chainsaws and trimmers, and as such, it comes sourced directly from the original manufacturer. This part ships individually.

The handle assist is the handle that is held to steer and control the machine during the trimming process. As the primary touchpoint, the handle has to provide enough comfort while assisting with the machine's function. This handle is designed to be gloves-friendly with a surface rough enough to provide security against slip. Use this as a replacement for a broken, loose, or worn handle. Remember always to hold the handle firmly while operating. This part is designed for use on trimmers or weed cutters made by Craftsman, Weed Eater, Poulan, or Poulan Pro. This is a genuine OEM replacement handle that will provide extra control and less hand fatigue. It is sold individually.

All gasoline-powered trimmers must have throttle controls that increase the amount of gasoline flowing into the carburetor. As the amount of fuel increases and the engine revolutions increase, the clutch engages the spool and the trimming line begins to turn. The throttle trigger assembly is quite durable. However, it has several appendages and is required to be under constant pressure when in use. If any of the design parts fail, the trigger unit must be replaced or the trimmer cannot be used. To replace the throttle trigger, open the housing and disconnect the throttle cable from the old trigger. It's easy to see where the new trigger will fit in the housing because the screw holes will line up perfectly with the holes in the new throttle trigger. The throttle cable will fit into one slot on the new trigger and a spring opposite the slot will hold the trigger unit at the proper angle as the housing is replaced. This new throttle trigger is an OEM replacement part, made to the same exacting specification as the original. This throttle control is designed by Craftsman and used on most of their trimmers. It is also compatible with a few other manufacturers' trimmers, including Poulan and Husqvarna.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

The lower shaft replacement is used for lawn and garden equipment such as trimmers, gas trimmers, and pruners. The shaft is the part that will hold the spool used on these types of equipment. It also connects to the upper shaft.Some of the common problems with the lower drive shaft include worn drive shaft ends, worn bushing, breaks along the metal, or damage to the outer tube. Owners should replace the lower shaft before they use the machine. Continuing to use a trimmer with a broken lower shaft is dangerous and could result in injury or more damage to the machine. The replacement of the lower shaft is relatively simple and will require only a few tools.The replacement part works with certain models of trimmer and pruner from Husqvarna, Weed Eater, and Poulan. This is a genuine OEM replacement part sourced from the manufacturer. The kit is sold individually.

This shield kit is a genuine Husqvarna replacement part for a line trimmers and pole saws. The shield kit, also known as a guard, is a safety precaution to protect the engine from damage and to protect the appliance user from flying debris. The shield also manages the amount of string trimmer line that is spooled out. The shield kit of a line trimmer or pole saw might have to be replaced if there is significant damage to the exterior. While shield kits for line trimmers and pole saws are designed to be durable, the exterior can be gradually worn away by collisions with flying debris and small stones, causing warping and erosion to the plastic material. If the shield kit is damaged, it must be removed and replaced immediately, as it is important for safe use of the appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shield kit is compatible with the following brands: Husqvarna, Weed Eater, Craftsman, and Poulan. This part sold individually.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This part is a replacement spring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. If the current spring is broken or defective, this part can be used as a replacement. It is intended for use with trimmers.The spring works by applying tension to the head of the trimmer. Over time and with regular use, springs can easily break or become eroded, requiring replacement. When working on or near an engine or blades, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this spring, the appropriate owner's manual and equipment diagrams should be referenced. This spring is suitable for use on a variety of trimmer models manufactured by Husqvarna and Poulan. It is a genuine OEM part and thus is made of high-quality, durable metal. Part sold individually.

This is a wound spool assembly that can be used on several models of lawn and garden equipment. The spool assembly is the part that holds the trimming line. It also operates by letting the line feed out when a trimmer or pruner is being used. The wound spool assembly is a component of the cutting head assembly but can be replaced as a single part. This wound spool assembly part experiences a great amount of wear and tear. It's not a bad idea to have an extra available for any needed replacement. If the spool assembly is broken or damaged, it can be replaced in just a few minutes. The first step is to power off the equipment and remove the spark plug wire. The cover should be removed to get access to the wound spool assembly. Switch it out with the replacement part.This wound spool assembly is sold as an individual part. It is a genuine OEM replacement part that is directly sourced from the manufacturer. The spool assembly is designed to be compatible with string trimmers and pole pruners manufactured by Poulan, Poulan Pro, and Husqvarna.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is a replacement knob for a trimmer. The plastic bump knob, which is connected to a spring, is used to secure the spool. A bump knob on a trimmer may get stuck or seized and will need a replacement. Before replacing the bump knob, remove the wire from the spark plug to avoid the accidental starting of the engine. Pull off the trimmer head housing and then use a flat head screwdriver to detach the old knob. Rotate it and then remove the component. Make sure the spring is in place then align the knob before rotating and snapping it in place. Take note that pulling the knob off may take extreme force when pulling. Some knobs are screw-mounted and a counterclockwise turn is necessary to unscrew it. This genuine OEM replacement part is sold individually and is compatible with specific trimmer models from Poulan and Weed Eater.