Parts for Troy-Bilt 1028: Handle Panel / Handle / Chutes Parts

This part is a replacement chute crank assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a broken or defective chute crank assembly on snowblowers. The chute crank assembly enables the equipment operator to adjust what direction snow is expelled from the chute. This is important for operation, as it allows the snow to be directed away from the area intended to be cleared. This part is subject to wear and tear can become dented, bent, broken, or otherwise damaged and will require replacement. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this chute crank assembly, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality metal. This chute crank can be used with a variety of snowblower models manufactured by MTD, Craftsman, Husky, and Yard Machines.

This carriage bolt is a genuine MTD part, sold individually. This carriage bolt can be used as a replacement part in lawnmowers, snowblowers, tillers, and edgers. The purpose of the carriage bolt for one of these outdoor appliances is to work in conjunction with a nut to affix two metal components to one another or one metal component to another wood component.The carriage bolt in an outdoor appliance might have to be completely replaced if it cannot affix two or more components together. This could occur if the carriage bolt has been punctured, dented, cracked, warped, or eroded to the point that it loses its functionality. If this occurs, the carriage bolt should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This carriage bolt is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, Yard-Man, and MasterCut.

This hex screw is a genuine MTD part, sold individually. This hex screw can be used as a replacement part in a variety of outdoor appliances including lawn mowers, snowblowers, and tillers.The hex screw in an outdoor appliance might have to be replaced if it is lost, misplaced, or stripped. The hex screw is a small component which can be easily lost during maintenance. It can also be damaged by exposure to the elements or from general wear and tear. If this occurs, the hex screw should be replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.

A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.

Carriage bolts are flat-tipped with round heads, and their function in small engine appliances is to fasten together components and to secure that connection with a nut. There are various reasons that a carriage bolt might have to be removed and replaced, among them misplacement of the small, easily lost part. Other reasons to replace a carriage bolt could include damage or erosion that prevents the bolt from attaching the materials to one another effectively. If a carriage bolt is subject to this kind of damage, it should be replaced before using the small engine appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This genuine MTD carriage bolt can be used as a replacement part for several different kinds of appliances that require small engines, including lawnmowers, snowblowers, wood-chippers, tillers, string trimmers, leaf blowers, and edgers. The OEM carriage bolt is compatible with the following brands: Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut. This part is sold individually.

This handle grip part is used on many kinds of lawn and garden equipment that is pushed or otherwise moved around a yard. The handle grips are made out of flexible rubber and are used on the two handles. The purpose of the handle grip is to offer a more secure grip on the power tool and lessen the feel of vibrations.Over time, one or both of the handle grips can start to experience wear. Sometimes, the grips will become damaged or broken. If the grips are very damaged, they may come off of the machinery. There is no need to use tools to replace the handle grip on yard equipment. The old part just needs to be removed from the tool so that the new component can be slipped on. Wear a pair of work gloves to make the process easier.This is a genuine OEM handle grip replacement that is sourced directly from the manufacturer. It is sold individually. The part is compatible with lawnmowers, snowblowers, tillers, and chainsaws created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.

This part is a replacement push nut. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or detached push nut in snow blowers.Push nuts are a special type of fastener that secures together different equipment components. Push nuts will need to be replaced if worn, broken, lost, or otherwise ineffective. When working on or near an engine, it's important to make sure the equipment is powered off and completely cool before starting any repairs. For more accurate information on how and where to install this push nut, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This push nut can be used with different models of snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Part sold individually.

This hex screw is a genuine MTD part. It is a replacement part for lawn tractors, edgers, lawn mowers, snow blowers, tillers, string trimmers, chainsaws, log splitters, and wood chippers. It is a standard-sized part and it may be compatible with other machines as well.This particular screw is a one-inch metal screw and may be found in various places on the pieces of equipment. Refer to a parts diagram to find out where it is used on the equipment.This hex screw is a genuine OEM part sourced directly from the manufacturer. It is sold individually. Most machines have multiple screws; check others to see if more need replacement. It is compatible with several makes, including but not limited to Bolens, MTD, Troy-Bilt, Yard-Man, Yard Machines, Ryobi, Husky, Cub Cadet, Montgomery Ward, MasterCut, Turf King, and more.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This oval screw is a genuine MTD part, sold individually. An oval screw can be used as a replacement part for outdoor appliances including humidifiers, lawn mowers, snowblowers, tillers, log splitters, and wood chippers.The oval screw for one of these outdoor appliances might be subject to enough damage that could mandate a complete replacement of the part. Additionally, the oval screw could be lost or misplaced, as it is a small component that might not alert the operator of the appliance to its absence immediately. Refer to the manual for detailed instructions.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This oval screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Ryobi, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Yard Man, Turf King, and MasterCut.

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This is a replacement bell washer, a flat washer that can be used with a wide range of various types of lawn and garden equipment. The inner dimension of this washer is 0.40 inches, while the outer dimension is 0.88 inches. Washers are typically used as a way to help ensure a tight connection when used with bolts or screws. They will also help to distribute the pressure of the connection and reduce the risk of corrosion. Washers will also provide some protection from damage during installation. Washers could need to be replaced for any number of reasons. In some cases, they might have become corroded or worn down over time. This could mean they no longer provide a solid and secure connection. Other times, the washer could become lost while working on the machine. Owners should always be sure that they replace any lost or damaged washers right away. Not using washers can reduce the lifespan of the machine. This is a genuine OEM bell washer that is sold individually. It is typically used in lawn mowers, snowblowers, tillers, leaf blowers, string trimmers, log splitters, wood chippers, edgers, and chainsaws. It is compatible with Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut brands.

This cam rod, also called a rod cam or a cam-rod, is a genuine MTD part. It is manufactured as a replacement part for snow blowers and snow throwers from a number of makers.This rod is long and thin, and although the original is made from durable material, it can become warped or damaged over time. It is an important component in the push function of the machine and must be replaced if damaged for safety purposes.This cam rod is a genuine OEM part which is sourced directly from the manufacturer. It is sold individually. It is compatible with snow blowers and snow throwers made by ACE, Craftsman, Huskee, Husky, Lawn Chief, Montgomery Ward, MTD, Power Pro, Ranch King, Ryobi, Select Series, White Outdoor, Yard Machines, and Yard-Man. Many of the compatible machines were made in the 1990s.

This part is a replacement handle bracket. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace broken or defective handle brackets in a variety of snow blower and snow thrower models. This handle bracket secures the handle of the snow blower or snow thrower so the equipment can be properly and safely used. If the bracket is detached, bent, dented, or broken, the handle may become detached. Thus, the handle bracket should be replaced. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this handle bracket, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this handle bracket is suitable for use on several different models of snow blowers and snow throwers manufactured by MTD, Craftsman, Troy-Bilt, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

Screw hex caps are found on lawn equipment and other small machines. Over time, with the machine's use or following accidental damage, a screw hex cap may break or become loose. In order to continue safely operating the machine, the part must be replaced. A missing or damaged screw hex cap can cause the equipment to move in unpredictable ways. Check for excessive vibration or noise.Always wear gloves for protection when replacing parts on lawn equipment. Tools required may include a socket set, wrench set, and a screwdriver. Screw hex caps are quick and easy to replace. Make sure that the replacement screw hex cap is installed correctly and properly secured for a tight and long-lasting fit.This screw hex cap is an authentic OEM replacement part. It is supplied by the manufacturer. The replacement screw hex cap is made of durable metal and is gold in color. The replacement piece can be used in a variety of machines, including chippers, shredders, cultivators, edgers, lawnmowers, lawn tractors, and snowblowers. The screw hex cap is compatible with Husky, Cub Cadet, Ryobi, Bolens, Yard Machines, Yard-Man, Troy-Bilt, and MTD. It is sold as an individual unit.

This is a versatile screw designed with flanged hex head and double-lead threads. It is a high-low self-tapping screw with one thread that is high and the other low for easier penetration. The twin threads also reduce the amount of material displaced when the screw is driven into the material. This type of screw also creates a firmer grip. This screw can also be used to secure a newly installed front cover or grill. This part is available as an individual replacement part. It is a genuine OEM part for use with specific models of snow throwers, lawn tractors, electric mowers, chippers, and log splitters from Bolens, Cub Cadet, Craftsman, Poulan, Ryobi, Toro, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

This is a chute crank bracket for a snow blower. The bracket holds and positions the chute in the proper direction so that snow is thrown at the desired angle. This is a genuine OEM part and is sold individually. This part is compatible with several brands, including Craftsman, Huskee, Ryobi, Troy-Bilt, Yard Machines, and Yard Man.If the crank bracket is rusted, damaged, or bent, it can affect the efficiency of the snow blower and throw the snow in the wrong direction or clog the chute. Replacing the bracket is fairly simple and will help the snow to be thrown efficiently and without clogging. For proper placement of the chute, remove it from the bracket and be sure that it moves easily. When attached, if the teeth do not mesh correctly, the bracket will need to be readjusted or replaced. This is easily done by loosening the bolts and moving the bracket until the teeth mesh. This will allow the chute to turn correctly. If the teeth will still not mesh, detach the chute and then remove the bad bracket and install the new bracket.

A carriage bolt is a type of fastener. It features a smooth rounded head and a square domed top. It has threading, which leads to up to the square shoulder. The purpose of its square is to prevent the bolt from spinning. Once the carriage bolt is inserted through the hole, using a nut and washer can provide additional security. Carriage bolts can corrode and loosen over time. Since it doesn't have a slotted head, a socket wrench is needed when replacing. This bolt carriage replacement is compatible with wood chippers, tillers, string trimmers, lawnmowers, and edgers. It is a genuine MTD product that measures 5/16x.075. It has a smooth rounded head and square shoulder underneath it. This carriage bolt is sold individually.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

This is a carriage bolt, which is found on lawnmowers, snowblowers, and many other types of lawn and garden equipment. The carriage bolt is made of metal and the location will vary based on the model of the tool. The carriage bolt is used to fasten together two components on lawn and garden equipment. It can become damaged, break, or stripped and will need to be replaced.If the carriage bolt is broken, stripped, or has damage, a wrench will be needed to replace it. Make sure that the spark plug wire has been disconnected and the tool is turned off before you begin. Use the wrench to remove the carriage bolt before installing the new part in the same location. Replace any additional disassembled components removed to gain access to the bolt before using the tool.This carriage bolt is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The bolt is designed to work with lawnmowers, chainsaws, snowblowers, tillers, and leaf blowers manufactured by Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Husky, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

This is a flat washer with an inner diameter of .469 inches. The washer is a replacement part that is for use with types of lawn and garden equipment. Flat washers help to increase the size of a screw's bearing surface area. It will help to reduce the surface pressure that is applied when the pieces are fastened together, and it will help to protect the pieces being connected.The flat washer is made from metal, which means it is durable. However, even metal can start to wear away over time. It could become thinner, corrode, or even become cracked. When this happens, owners will need to replace the washer. In some cases, the washers might become lost when working on the machine. Getting a new washer to replace any that are missing is essential.The flat washer will work with a range of select machines including tillers, lawn tractors, snowblowers, cultivators, and mowers from Yard-Man, Troy-Bilt, Ryobi, MTD, Bolens, Yard Machines, Husky, and Cub Cadet. The washer is sold individually and is a genuine OEM replacement part.

This part is a replacement wire harness. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective wire harness in snow blowers.The wire harness is a critical electrical component that helps to power the snow blower. It's possible that the wire harness can become stretched, snapped, frayed, or otherwise faulty and will require replacement. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this wire harness, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This wire harness can be used with different models of snow blowers that have been manufactured by MTD, Craftsman, and other brands. Part sold individually.