Parts for Weedeater SST25C TYPE 1: Handle / Shield / Drive Shaft Parts

This is a trimmer throttle cable assembly meant to be compatible with trimmers from several top brands. The throttle cable is the part that connects the throttle trigger and the carburetor. It can allow the user to provide power to the machine by regulating the carburetor airflow. If the cable has a problem, users will not be able to control the throttle properly or at all in some cases.The throttle cable could become damaged and need to be replaced. There are connections on each end of the cable that could be damaged or broken. The cable might also kink, which could cause it to break. Owners can replace the cable and extend the life of the trimmer. Tools commonly used for replacement include a hex key, Torx screwdriver, or a screwdriver depending on the model.The throttle cable assembly works with certain models of trimmer from Husqvarna, Weed Eater, and Poulan. The cable is sold individually. This is an authentic OEM replacement that has been sourced from the manufacturer.

This genuine OEM trigger is used on several different types of outdoor equipment, including gas trimmers and edgers. The trigger is attached to the throttle cable to control the speed of the spool assembly. With pressure, the trigger pulls the throttle cable, and in turn, speeds up the spinning hub where the cutting is done. It allows for faster or more difficult cuts to be performed. With routine use of the outdoor equipment, the trigger can break, wear out, or malfunction. Without a properly working trigger, the equipment cannot be controlled with the expected manual adjustments.Replacing the trigger on an edger or trimmer is easy and requires only a screwdriver for most makes and models. Wear work gloves when replacing the trigger. Remove the screws from the control handle housing. Remove the trigger from the throttle cable and put the new one on. Screw back into place and replace the control handle housing.This trigger is a replacement part. It is sold separately. The trigger piece works in a wide assortment of both Husqvarna and Weed Eater trimmers and edgers. The trigger is manufactured using rigid, high-quality plastic, and it is yellow.

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Normally screws are found in many different types of appliances. These parts are important in holding different pieces together so that the user is able to operate the machine effectively. A new screw might be needed if some parts of the appliance are loose or missing from place.Screws can become stripped over time with normal equipment use. If this is the case it is recommended that they be replaced. The repair for this screw is simple and will most likely require common household tools as well as pliers. This screw is made of durable metal made for long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is also a genuine OEM replacement part.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This replacement part is a drive shaft kit and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This part is used in weed eaters and line trimmers and helps the user operate the appliance properly. This part allows the user to maintain full control over the appliance to get landscaping jobs done.A new drive shaft kit might be needed if the current part is damaged or broken in anyway including being dented, cracked, or snapped. It is possible that due to normal wear and tear this part becomes worn down overtime. Be sure to wear work gloves while replacing this part to prevent injury. Refer to the owners manual for more specific instructions on how to replace this part. This is a genuine OEM replacement part that is sourced directly from the manufacturer to ensure a proper fit and long lasting results. This part is sold individually.

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Normally screws are found in many different types of appliances. These parts are important in holding different pieces together so that the user is able to operate the machine effectively. A new screw might be needed if some parts of the appliance are loose or missing from place.Screws can become stripped over time with normal equipment use. If this is the case it is recommended that they be replaced. The repair for this screw is simple and will most likely require common household tools as well as pliers. This screw is made of durable metal made for long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is also a genuine OEM replacement part.

This replacement part is a shaft assembly and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This shaft assembly is typically found in grass trimmers. The shaft assembly connects the top of the trimmer to the bottom mechanisms which allow the user to control the settings in the trimmer. A new shaft assembly might be needed if the user is unable to control the gear at the lower end of the trimmer. It is possible that the shaft can become damaged with normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a screw. This is a genuine Husqvarna replacement screw and has been sourced directly from the manufacturer. This replacement part is a high-quality piece of standard hardware with many different applications. For proper installation instructions and usage guidance, it is recommended to refer to the equipment diagram supplied specifically by the manufacturer. It's common over time and with regular usage for screws to easily become stripped, rusted, broken, or lost. This can lead to improper functionality of outdoor power equipment. It's important to always use genuine manufacturer replacement screws to ensure the highest-quality materials and a proper fit. When installing screws, always follow proper guidelines and abide by appropriate safety measures. Husqvarna screws are manufactured from high-quality, durable metal. This replacement screw is designed to various models of trimmers and hedge trimmers, blowers, and chainsaws manufactured by Husqvarna, Craftsman, Poulan, and Weed Eater. Please note this screw is a genuine OEM part made of durable, non-corrosive metal and is sold individually.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This is a replacement fixed line cutting head. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended to replace a broken, worn, or defective fixed line cutting head on various trimmer models. The cutting head cuts through weeds, plants, and grass. Due to the amount of contact this part has with the ground, rough surfaces, and debris, it can easily become worn and require replacement. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. Proper tools may be required to replace this part. For more accurate information on how and where to install this fixed line cutting head, reference the appropriate owner's manual and included diagrams.As an authentic replacement part, this fixed line cutting head is suitable for use on several different models of string trimmers manufactured by Husqvarna, WeedEater, and Poulan. This is a genuine part made of high-quality, durable materials and is sold individually.

This part is a replacement fixed line cap. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. It is intended to replace a broken or defective fixed line cap in line trimmers.This fixed line cap fixes to the bottom of the trimmer head and securely holds the trimmer line into place. This cap is subject to wear and tear over time and with regular equipment usage and thus may require replacement if broken or detached. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this fixed line cap, the appropriate owner's manual and equipment diagrams should be referred to. This fixed line cap is a genuine OEM part made of durable plastic and is sold individually. It is suitable for use with line trimmer models that have been manufactured by Husqvarna, Poulan, and other brands.