Parts for Kitchenaid KXW8736YSS0: 01 - Hood Parts

This hood damper controls air flow in the exhaust vent, stopping outside air and fumes from entering when the range hood or microwave vent is off. It restores proper venting and reduces drafts. What it does:

• Opens to allow exhaust airflow when the hood or microwave vent runs
• Closes to block outside air and backdrafts when the fan is off
• Helps reduce unwanted odors and kitchen drafts caused by a stuck damper
• Can eliminate rattling or flapping noises if the original damper is loose or damaged

• One hood damper

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Access may require removing the hood or microwave vent grille; keep hardware for reassembly
• Verify damper orientation and smooth operation before completing installation

Bulb only - Socket must be ordered separately

This is a replacement electrical socket used to reconnect wiring to an appliance component, restoring a secure, insulated connection and reliable electrical contact. It's a like-for-like connector designed for direct replacement of a damaged or worn socket. What it does:

• Provides a secure electrical connection between wiring and a component to restore power or signal flow
• Replaces cracked, melted, loose, or corroded sockets that cause intermittent operation or failure
• Helps prevent short circuits and arcing by restoring proper insulation and fit
• Fits into the existing wiring harness or component receptacle to restore OEM-style connections

• One replacement electrical socket

• Disconnect power (unplug or shut off circuit breaker) before beginning any repair
• Inspect mating terminals, harness, and surrounding insulation; replace damaged wiring or terminals as needed
• Ensure correct orientation and full seating of the socket; confirm secure wire crimps or fasteners

This grease channel is the molded drip tray that collects and routes cooking grease away from the vent/hood area to help keep the appliance interior cleaner and reduce smoke buildup. Durable replacement for worn or cracked channels. What it does:

• Captures and channels drips and grease from the cooking surface or vent inlet
• Prevents grease from pooling inside the vent or cabinet area
• Helps reduce smoke, odors and potential staining from accumulated grease
• Restores proper drainage when the original channel is cracked, warped or missing

• One grease channel/drip tray as pictured

• Follow the appliance service manual for access and removal steps; appliance disassembly may be required
• Use appropriate hand tools; avoid sharp edges on metal housings and wear gloves
• Disconnect power (and gas if applicable) before servicing to avoid injury
• Only reinstall if the channel seats properly and does not interfere with other parts

This replacement refrigerator water filter helps improve water and ice taste by trapping common impurities. It restores cleaner-tasting water for drinking and cooking when your existing filter is old or clogged. What it does:

• Filters water to help reduce common contaminants that affect taste and clarity
• Helps improve the taste and odor of dispensed water and ice
• Addresses symptoms like unusual water taste, cloudy ice, or reduced water flow from the dispenser
• Restores proper filtering performance when the old filter is past its service life

• Turn off water supply to the refrigerator before removing the old filter.
• Follow your refrigerator's filter removal/installation steps; typically push/rotate or pull to remove and insert until secure.
• Flush several quarts of water through the dispenser after installation to clear air and initial carbon fines.
• Dispose of the used filter according to local regulations.

This is a replacement refrigerator water filter cartridge that helps restore clearer, better-tasting water and ice. Use when your dispenser or ice maker produces cloudy water, unpleasant taste or odors, or reduced water quality. What it does:

• Traps common particles and sediment that cause cloudy water
• Reduces chlorine taste and odor to improve water and ice flavor
• Helps maintain normal dispenser and icemaker performance related to water quality
• Provides a direct-replacement fit when the OEM filter is removed and replaced

• Turn off the water supply and dispense water to relieve pressure before removing the old filter.
• Remove the old filter per your refrigerator's OEM instructions and install the new cartridge until it seats securely.
• Run several gallons of water through the dispenser after installing to flush the system and clear air.
• Follow the refrigerator OEM for recommended replacement interval and any filter reset procedures.

Note: This is the top switch panel only.

The Control Knob is an OEM component specifically designed for Whirlpool and KitchenAid ranges. Located on the range control panel, this knob securely attaches to the temperature dial and allows for easy adjustment of burner temperatures. A dependable control knob facilitates simple, intuitive stovetop operation.

Causes of a faulty knob can include wear from frequent use, damage or cracks to the knob base or connector, or premature degradation of plastic components. 

Symptoms of a bad control knob include:

• Loose, wobbly, or detached knob that won’t stay securely in place
• Difficulty adjusting burner heat levels precisely  
• Potential knob breakage or non-functional temperature dial 
• Inability to maintain desired cooking temperatures

This OEM part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This slide-style electrical switch selects or turns a function on and off inside the appliance. Replacing a worn switch restores reliable control when settings won't engage, respond intermittently, or the slider feels loose or broken. What it does

• Provides sliding on/off or multi-position selection for a specific feature
• Routes power to the associated component when a position is selected
• Helps restore proper response when a control becomes intermittent or unresponsive
• Common signs: slider sticks, feels loose, breaks, or shows heat discoloration on terminals

• 1 slide switch

• Disconnect power to the appliance before service
• Access the control panel; note wire locations and take a clear photo
• Move wires to the new switch one at a time; fully seat each connector
• Reassemble, restore power, and test each switch position

This rocker switch restores dependable on/off control for a selected function on your appliance. Replace a worn or intermittent switch to fix features that won't turn on or off and bring normal operation back. What it does:

• Controls power to a single function when pressed
• Common symptoms: feature won't turn on/off or only works intermittently
• Switch feels loose, sticks, or requires wiggling to engage
• Resolve issues caused by worn internal contacts or heat discoloration

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Note wire positions or take a photo; move wires to the new switch one at a time
• Seat the switch securely in the panel or bracket to avoid pinched wires
• Restore power and test operation

A direct-replacement rocker switch for control panels that restores a positive on/off or function selection when the original switch has worn or failed. Fits common Whirlpool control-panel applications to help regain reliable button function. What it does

• Opens and closes the electrical circuit for a specific control function on the appliance control panel.
• Replaces a worn, cracked, or non-responsive rocker that fails to click or hold a selection.
• Can resolve intermittent operation, no power to a single function, or tactile button failure.
• Designed to match OEM terminal layout for a direct electrical swap when the correct part is used.

• One rocker switch.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Remove the control panel or access panel to reach the switch; note wire positions or take a photo before disconnecting.
• Pull off quick-connect terminals with pliers or a terminal tool and transfer wires to the replacement in the same order.
• After installation, restore power and test the function before fully reassembling the appliance.

This complete motor assembly replaces the dryer drive motor to restore drum rotation and normal drying operation. It's a direct-fit, factory-style motor that helps resolve stopping, no-tumble, or noisy motor issues. What it does

• Drives the dryer drum and internal components so laundry tumbles during cycles.
• Powers the blower and other linked mechanisms required for normal drying.
• Commonly used when the dryer won't spin, stops mid-cycle, or makes loud grinding or humming noises.
• Can resolve intermittent starting problems or slow/no rotation caused by a failed motor.

• One complete motor assembly

• Disconnect power before servicing to avoid shock—this part services high-voltage equipment.
• Follow the dryer's service manual for removal/installation steps; panels and belts may need to be removed.
• Inspect and, if needed, replace associated parts (belt, idler, blower) if damaged or worn.