Huskee / Husky Chipper Shredder Parts

This part is an adjustable gib that is used on log splitters and chipper shredders. This component is also called a keyway. The adjustable gib locks two shafts together so that they can rotate.A new adjustable gib may be needed if the shaft is freely spinning and will not spin with the drive shaft. If the adjustable gib is cracked, broken, or damaged in any way, it will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This adjustable gib is a genuine MTD part. It is sold individually. This specific adjustable gib is compatible with log splitters and chipper shredders that are manufactured by MTD, Yard Machines, Cub Cadet, Yard-Man, Husky, and Troy-Bilt.

This genuine MTD shredder screen determines the size of the shreds that the wood chipper will produce. A shredder screen covers any number of shapes and sizes of screens through which the wood will be chipped.A shredder screen might have to be replaced in the event that it suffers damage over time or in the case that the wood chipper encounters wood that is too hard or too brittle, which can break the shredder screen. The bars of a shredder screen can be welded back into shape by hand, but it is easier and safer to order a replacement shredder screen if it is subject to breaking, piercing, puncturing, or erosion to the metal material. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shredder screen is compatible with the following brands: MTD, Cub Cadet, Yard Machines, Yard-Man, Craftsman, and Troy-Bilt. This part is sold individually.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This is a replacement part for select riding mowers designed to ensure smooth rotation for years of use. This part is circular and tapers off into a hexagonal shape to support rotating shafts that create friction inside of machinery. Rotating parts are almost a given in most machinery like riding mowers, so the hex flange bearing provides support in multiple ways to parts such as wheels, rotors, and gears.The hex flange bearing serves two fundamental roles to make machinery run efficiently. For starters, friction will inevitably occur in rotating shafts, so bearings reduce the amount of friction and related wear and tear. The second function of this part is protecting the rotating from damage due to pressure created during operation.This genuine OEM sourced replacement part is intended to be used for lawn tractors from MTD and other yard machines. This part is compatible with manufacturers including Yard Machines, Bolens, Yard Man, Troy-Bilt, Cub Cadet, and Husky. A wrench may be used for an easier replacement installation. This item is available for purchase individually.

This part is a replacement mandrel bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken mandrel bearing in a variety of lawn tractor models. Mandrel bearings are a critical component that ensures no excess heat, friction, or vibration occurs while the equipment is in use. Bearings are subject to wear and tear and will require replacement when no longer working effectively. When working on or near an engine, it's important to ensure that the equipment is powered off and completely cool before beginning any repairs. For more accurate information on how and where to place this mandrel bearing, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this mandrel bearing is suitable for use on lawn tractors manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The purpose of a carburetor insulator is to keep the heat of the running engine away from the carburetor, which combines the air and fuel that ignites the engine. This keeps the engine from overheating and suffering damage as a result.While there is a chance that a damaged carburetor insulator could prevent the engine from igniting altogether, it is more likely that a damaged carburetor insulator will allow for unmetered air leaks into the carburetor. Unmetered air leaks will cause the engine to take in more fuel, reducing the fuel economy of a small engine appliance. For this reason, if the symptoms align with a diagnosis of a damaged carburetor insulator, it must be individually replaced as soon as possible before using the small engine lawn appliance again.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.

This is a replacement hex screw sourced from the manufacturer. The hex screw is used in numerous machines, including lawnmowers, tractors, and tillers.Hex screws will be subject to normal wear like any other part. They should be inspected every year before using the equipment for rust or to see if any have fallen out or broken off. If any extra motion from the deck or the engine is noticeable, check the screws to ensure they don't need to be tightened. Failure to do so can cause damage to mower and cause other parts to need replacement.Before checking the screws, make sure the mower has cooled off to avoid burns. They can be tightened with a rachet or an adjustable wrench. The hex screw is a genuine OEM replacement part. It is designed to be used with Craftsman, Troy-Bilt, Cub Cadet, MTD, Yard Man, and other brands.

This carriage bolt is a self-locking fastener made for use in round or square holes to attach metal to metal in outdoor equipment. These bolts provide an added safety feature because they can only be removed from one side. Carriage bolts can carry a large amount of weight, which makes them ideal for use in outdoor yard equipment. Carriage bolts may be used to attach a lawn mower's arm to the side support and other similar applications. If the bolt needs to be replaced, removal and installation are simple. Use a wrench to loosen the nut holding the washer and bolt in place. Once the nut is loose, the bolt can be unthreaded by hand and pulled out of the hole. To install, push the bolt back through the hole. If the fit is too tight to install by hand, use a hammer to tap it in place. Reinstall the washer and nut and tighten with a wrench.This carriage bolt is designed for use in lawnmowers, snowblowers, and lawn tractors manufactured by Craftsman, Bolens, Yard Machines, Yard-Man, and MTD. This is a genuine OEM product that comes directly from the manufacturer. Note: It does not come with a nut or washer.

This hex screw and lock washer are commonly used with lawn mowers and other small engines to secure a motor to the housing of the equipment. It is machined in such a way that it binds the manifold and frame permanently. There are occasions when these bolts have to be removed, typically when major repairs are performed on the engine. In those cases, users often find it advisable to replace the hex bolts and washers with new ones. It happens as well that these screws are so tightly fastened that they cannot be unscrewed and must be cut off. In those cases, it is necessary to replace the original screws. These replacement screws and lock washers are genuine OEM certified replacements that are manufactured to be identical to the hardware they are replacing. In addition to mowers, these hex screws are used to secure engines to devices such as log splitters, edgers, shredders, trimmers, and snowblowers. This screw is compatible with devices made by Husky, Yard-Man, Cub Cadet, Troy-Bilt, Ryobi, Bolens, and Yard Machines.

This part is a hex cap screw that is used on a variety of outdoor power equipment. A hex cap screw is used to fasten components together securely. The head of the screw is shaped like a hexagon, hence the name "hex cap screw."A new hex cap screw may be needed if the current one is stripped, broken, or missing. Since screws are such a small component, it is important to place them in a safe place so that they are not lost. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This hex cap screw is a genuine Husqvarna part. It is sold individually. This particular hex cap screw is compatible with chippers, shredders, lawnmowers, lawn tractors, snowblowers, and vacuums that are manufactured by the following brands: Husqvarna, Craftsman, Bolens, Husky, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

This hex bolt is a genuine MTD part, sold individually. This hex bolt can be used as a replacement part in lawn mowers, edgers, log splitters, and wood chippers. The purpose of the hex bolt for these outdoor appliances is to serve as a fastening component in conjunction with a nut so that one or more components can be held together with the aid of this fastener.The hex bolt in an outdoor appliance might need to be replaced if it is lost, misplaced, or stripped. If the hex bolt is lost or misplaced, it should be replaced by this genuine OEM replacement part. If the hex bolt suffers damage in the form of scraping, denting, cracking, or eroding over time, the component should be replaced immediately.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This hex bolt is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Yard Machines, Huskee, Yard Man, and MasterCut.

This replacement part is a hex screw. It is a genuine replacement part made by MTD. Hex screws are able to hold other parts in place and secure them so that everything can operate smoothly. This part is small yet very important to the overall operation of many different machines.A new hex screw might be needed if the user notices that the current ones are damaged or missing. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. It is possible that screws become stripped or lodged over time and should be replaced when this occurs. Be sure the engine is completely powered down before starting a repair. This is a genuine OEM replacement part sourced directly from the manufacturer. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one.

This is a replacement screw for lawn and garden equipment that is typically used on the blades. The flat head of the screw ensures that they will sit flush once they have been installed. These screws, which have hex-socket heads, are often found on the blades of chippers and shredders. If a blade is loose, it could be a problem with the screws that are holding it in place. This could make the machine inefficient and even dangerous to operate. Therefore, if there are screws that are worn down or that are no longer doing their job, it is important to replace them. It is essential to use the appropriate screws for a repair. This is a genuine OEM sourced replacement part that comes from the manufacturer. This helps to ensure quality and compatibility. The screw is sold individually. It is compatible with a range of chippers and shredders from MTD, Troy-Bilt, Cub Cadet, Ryobi, Yard-Man, Yard Machines, and Mastercut.