Huskee / Husky Engine Parts

This is an oil filter designed to fit a variety of small, gasoline-powered motors used primarily on lawn equipment. This genuine OEM replacement filter removes contaminants that otherwise would wear down the internal working parts of the engine. While the filter works very well, it should be replaced annually as a part of regular maintenance. Depending on use, the filter may need to be replaced more often. When replacing the oil filter, the crankcase oil must be drained and safely discarded as well. To remove oil from the gasoline engine, start the engine and let it run for a couple of minutes. This circulates the oil and heats the internal engine parts so oil is better able to drain. Next, remove the drain plug located on the bottom of the oil pan and collect the oil. Remember to dispose of the oil safely where it cannot contaminate streams or aquifers. Once the oil has been removed, remove the old filter and discard it properly. The new filter should only be hand-tightened in place as using a wrench may cause the filter gasket to seal to the engine block. This filter will fit Yard Machine mower engines and MTD equipment.

Installing a brand-new air filter keeps the engine in top running condition. When the machine is in operation, the vacuumed air goes through the air filter. Any dirt or dust is left in the filter media. Over time, the filter will become dirty and can no longer provide the same filtering efficiency as before. If left ignored, the tiny particles could clog the engine and the carburetor. You may experience misfires and no engine start-up. An air filter replacement is cheap and easy to do. Simply remove the air cleaner cover and take out the dirty filter. Insert the new filter into the housing. This replacement will take less than 5 minutes. A screwdriver will be needed. The MTD 951-10298 Air Cleaner Kit is a genuine air filter from MTD. Each kit comes with one paper filter and one foam filter. The foam filter can be cleaned with water and detergent. The paper filter, however, needs replacement at least once a year. This air filter kit is compatible with Cub Cadet, PowerMore, and Troy-Bilt. It can also work with other garden equipment like wheel string trimmers, chipper-shredder vacuums, and log splitters.

This is a genuine replacement bolt that is designed specifically for use on select lawn tractors. This tractor bolt is a specialty piece of hardware designed for use on the steering segment gear. This screw holds the gear in place and is exposed to constant vibrations and repetitive motion as a result. Over time, that can result in damage, wear, or even total breakage of the bolt and require a replacement. If the bolt isn't functional or is missing, the steering segment gear will not be secured and that can lead to further damage if left unattended. Using a genuine replacement part like this will guarantee an exact fit for compatible models. This genuine OEM gear bolt is manufactured by MTD. It is compatible with lawn and garden equipment from RYOBI, HUSKEE, Troy-Bilt, Bolens, Yard Machines, Yard Man, and Cub Cadet, along with select models from MTD. The bolt works for more than 100 compatible models. It is made of durable metal and sold as an individual unit. A wrench or socket will be required to replace this part. Always wear gloves when performing repairs on lawn and garden equipment and allow the engine to cool before doing any work.

This replacement part air cleaner is an OEM part for use in small engines used in outdoor equipment, such as tillers and dethatchers. The air cleaner is responsible for ensuring that clean air is brought into the engine to provide optimal performance. It is a good idea to inspect the air cleaner assembly regularly to ensure that there is no damage or cracks that could allow dirt and debris to get into the engine. If there are any issues, get a replacement before operating the engine again. This will ensure that there is no additional dirt getting into the engine. The genuine OEM air cleaner is a quality item that comes from the manufacturer. It is sold individually. It can work with tillers and other machines from top brands like MTD, Craftsman, and Yard Machines.

A cotter pin is a standard piece of hardware typically used on lawn and garden equipment as a method of securing something to an axle or round shaft. These pins are thin and, although they are durable, they can rust or become damaged over time. In some instances, they can break off or become lost in the process of other repairs. A replacement with the right size and style of cotter pin will ensure that equipment is in working order at all times. This genuine OEM cotter pin replacement can be used with select lawn and garden equipment from MTD, Huskee, Yard Man, Yard Machines, Troy-Bilt, Bolens, Cub Cadet, and Murray. It can be used on lawn tractors, log splitters, chipper/shredder units, and snowblowers. There are more than 150 compatible units, so owners should consult their parts diagram for application(s) of this pin. Note that this pin may have multiple applications on a single machine. This cotter pin is sold individually and may require needle nose pliers to replace.

This is a genuine replacement shoulder screw that is compatible with select models of lawn tractors. The shoulder screw has multiple applications in lawn tractors, where it is typically used as some kind of axle for wheels or other components. Over time, this type of screw can become worn from repetitive motion or the threads can start to strip. If the screw fails or is unable to work effectively, it can affect whatever it is responsible for securing or holding, as well. This could result in the entire machine not working until a replacement is made. This is a genuine manufacturer's replacement manufactured by MTD. It is compatible with their lawn tractors as well as those from Yard Machines, Troy-Bilt, Yard Man, Husky, and Cub Cadet. The screw is made of durable metal and is sold as a single unit. This is considered specialty hardware and is also sometimes referred to as a shoulder bolt.

The recoil starter assembly starts the engine by using the grip to pull the rope, which activates the starter pulley and spring, causing the flywheel to rotate and start the engine. Over time, the starter spring can become stretched, causing the rope to seize up or fail to retract. The housing itself could also become damaged. It’s often easiest to replace the entire recoil starter assembly with this OEM model rather than individual components. The installation can be done quickly with a screwdriver and wrench by removing the three bolts that hold the assembly in place. This genuine OEM part is manufactured by MTD. It fits lawn mowers, tillers, log splitters, and other small engines made by MTD, as well as models from Bolens, Yard-Man, Yard Machines, Cub Cadet, Troy-Bilt, and Husky. This part includes the starter housing that protects the flywheel and other internal components, along with a starter pulley, spring, pull rope, and grip. The hardware required for this assembly is not included and must be purchased separately.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

This hex nut is designed for use with select trimmers and mowers. It is a standard hardware part that may have multiple applications depending on the type of unit and model. The nut is typically used to secure engine components or housing elements to provide safe use of the machine. These nuts are durable, but they are small and can become lost during other repairs. The constant exposure to vibrations and use can also cause them to strip or become damaged over time. Either way, a replacement with this genuine hex nut will resolve the issue and get equipment back in working order. This genuine OEM hex nut is manufactured to exact standards and sourced from the manufacturer. It can be used with trimmers and mowers from RYOBI, MTD, Bolens, Troy-Bilt, Yard Machines, Huskee, Yard Man, and Cub Cadet. Check the parts diagram for exact application and location of this nut and note that it may have multiple uses on select models. This hex nut is sold individually, and additional nuts will require the purchase of multiple pieces. In order to replace this nut, a hex socket wrench and driver will be required. Always wear gloves for safety.

This flat washer is used to attach the idler pulley in a number of small and medium sized gasoline powered engines. These engines include snow blowers, log splitters, riding mowers, lawn tractors, and chippers. Because the idler pulley is subject to a great deal of resistance when the pulley is engaged, eventually the pulley will wear out. Should there be a squealing sound when engaging the drive, the problem is likely the idler pulley. In these cases, the pulley must be replaced. It is a good idea to replace the surrounding hardware when replacing the idler pulley; tNhis includes the flat washer, which is subject to corrosion during heavy use. To replace the idler pulley, first detach the spark plug cap. If on a mower or tractor, drop the mower deck. Remove the original pulley and install in order: replacement pulley, hex bolt, flat washer, flange nut. Apart from dropping the mower deck, the only tools required to complete this installation may be a 9/16 ratchet and combination wrench. This washer is a genuine OEM replacement part, designed to perfectly replicate the original piece. This washer is compatible with Troy-Bilt, Yard Man, Yard Machines, MTD, and Craftsman devices.

This lift cable is designed for use with many lawnmowers and snowblowers to ensure that the gears run smoothly while using the equipment. The lift cable is made of durable materials but has delicate connectors on each end which may eventually wear out. When the connectors or cables are damaged, the part will need to be replaced. This component is important since it helps control how fast the blades or other parts of the tool can operate. If the cable breaks, the tool may not start.If the lift cable has gone bad, is worn out, or is damaged, replacement is needed. There will be no need to use tools during the process, but work gloves can be helpful. The lift cable can be untwisted from the housing and removed from the tool. Take the new component and place it in the same location. Make sure to reassemble any additional parts before useThis is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The lift cable is made to fit lawnmowers and snowblowers manufactured by Craftsman, Toro, Cub Cadet, Troy-Bilt, MTD, Huskee, Montgomery Wards, and Yard-Man.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

The ignition coil is a standard part of internal combustion engines on lawn and garden equipment. This coil consists of the ignition plug, plastic housing, and metal wires that include a flexible plastic casing. The coil is responsible for connecting the spark plug and transmitting the current that creates the spark that allows the engine to fire. This coil may develop wiring problems or the rubber and plastic parts may become worn and damaged over time. This will require a full replacement of the assembly. It is a good idea to inspect the coil when changing the spark plug as a part of routine maintenance, as well. This genuine OEM ignition coil is compatible with lawn and garden equipment from Troy-Bilt, MTD, Yard Machines, Yard Man, HUSKEE, and Cub Cadet. It can be used on more than 150 lawn and garden machines, including lawn mowers, log splitters, and chipper/shredder models. This coil assembly includes the ignition plug, metal wires encased in plastic, and a plastic housing. The hardware required to install this part is sold separately, as are all other components. Be sure to wear gloves and allow the engine to cool before working on the ignition or other components.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

This carburetor is a genuine MTD part. A carburetor is a tube that filters the air and fuel through the valves of the engine. This carburetor works with small engine devices such as snowblowers and lawn mowers. Natural wear and tear from the usage of an engine over a long period of time can cause the individual components within the engine to malfunction or fall into disrepair. The longer that a carburetor is in use without replacement, the more likely it is to become damaged or weakened, which will require a swift replacement. Signs of weakening infrastructure for which the carburetor might be responsible can include an engine that frequently stalls or will not start, a clotted fuel bowl blocked by dirt and gunk that results in overflowing fuel through the engine's vents, a poor ratio of air and fuel that results in wheezing, hissing, or popping engine noises, or a poor ratio of air and fuel that results in black smoke pouring out of the engine. Any of these symptoms in an engine will require the immediate replacement of the carburetor.