Huskee / Husky Tiller Spring Parts

This is a spring switch that is used in many types of lawn and garden equipment, such as log splitters, lawnmowers, and tillers. The spring switch is made out of durable metal and is typically located near the switch button. With ordinary use, the spring switch can experience wear or other types of damage and stop working correctly. When this occurs, it will need to be replaced.If the spring switch is broken or bent, a screwdriver will be needed to replace it. The lawn equipment should be powered off and placed on a stable surface during the replacement. Disassemble the unit and locate the contacts to access the spring switch and other small parts. The original switch can be removed using a screwdriver so the new component can be installed. Reassemble and power the tool on before use.This spring switch is a genuine OEM replacement part that is sourced directly from the manufacturer. The component is sold on an individual basis. The part is made to be compatible with lawnmowers, snowblowers, tillers, log splitters, and wood chippers manufactured by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, MasterCut, and Turf King.

This genuine OEM replacement part is an extension spring for a Craftsman snowblower idler pulley assembly. The idler pulley attaches to a part of the snowblower's housing and is helps to transfer energy throughout the belt drive. This extension spring helps to redistribute some of the back-and-forth motion created in the pulley as the snowblower runs. This keeps the assembly from shifting out of place and potentially slipping. This extension spring is attached at two points and, if pulled in both directions too far, can eventually lose some of its tension. When this happens, the idler assembly can begin to shake and even slip out of place. Replacing the extension spring is an easy job that will only require a socket wrench to remove the idler pulley. A pair of pliers may help to remove the spring from its clips. This part is only compatible with Craftsman snowblowers and is sourced from its original manufacturer. It ships individually and any additional parts needed will have to be purchased separately.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

This part is a replacement spring. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective spring in lawn tractors and snow blowers.Springs are an essential equipment component that can be easily broken, stretched, snapped, bent, or otherwise rendered ineffective. If the user notices any issues with the equipment's springs, they should replace them immediately with a genuine OEM replacement part. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this spring, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality metal. This spring can be used with different models of lawn tractors and snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Part sold individually.

This governor spring is a genuine MTD part, sold individually. This governor spring can be used as a replacement part in lawn mowers, tillers, leaf blowers, log splitters, and wood chippers. The purpose of a governor spring for these outdoor appliances is to facilitate the opening and closing of the throttle which helps the appliance maintain its even pace and speed while in operation.The governor spring in an outdoor appliance might have to be replaced if it loses its spring tension. This could occur as the result of a collision with a hard object or due to general wear and tear over long-term use. If this damage prevents the governor spring from serving its typical function, it should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This governor spring is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Craftsman, Troy-Bilt, Yard Machines, Huskee, Yard Man, and MasterCut.

This governor return spring is an essential part designed for use with outdoor lawn and garden power equipment that have small engines, such as a lawn mower, a tiller, a leaf blower, and a wood chipper. It is compatible with products by brands such as Cub Cadet, Yard Machines, MTD, Huskee, and Yard-Man.The purpose of the governor return spring is to apply tension to the throttle, which in turn controls the speed of the engine. Over the life of the machine, many components, such as the governor return spring, undergo normal wear and tear. The most common reason for replacing the governor spring is when it is worn out or broken. Signs and symptoms that it is time to replace the governor return spring include deterioration that is causing the engine to over-speed or run improperly. The replacement or repair process of the governor return spring should be straightforward, though the user should plan on using needle nose pliers for the replacement process. Always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This governor return spring is made out of metal. This governor return spring is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

This replacement part is an extension spring and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This extension spring is found in different types of lawn mowers and helps other parts to work together and allow the engine to run properly and smoothly.A new extension spring might be needed if the current one is damaged or missing from the appliance. Because of the nature of the extension spring, it is not unusual for it to become stripped or snapped due to normal wear and tear within the machine. Unusual sounds may come from inside the machine if this spring is not working properly. This is a genuine OEM replacement part and is sold individually. This spring is sourced directly from the manufacturer to ensure proper fit.