Husqvarna Hedge Trimmer Parts

Engine piston kit for gas trimmers and outdoor equipment. Replaces worn, damaged, or corroded pistons that cause poor compression and engine performance.

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Engine won't engage when pulling starter rope? The starter pawl bridge connects the flywheel to spin your trimmer's engine. Easy DIY repair.

Seals the fuel line where it passes through the chainsaw fuel tank. Replace if cracked, worn, or leaking to prevent fuel seepage and maintain proper seal.

Piston ring seals the space between piston and cylinder wall in gas-powered outdoor power equipment engines. Replace if worn, cracked, or causing smoke.

Cleans fuel before it enters the carburetor, catching dirt and debris. Replace when clogged to restore peak engine performance and prevent starting issues.

This ball bearing and seal are used in a range of chainsaw models. It acts as part of the blade assembly and is designed to both lessen friction and stabilize moving parts. This bearing is also set within a race and the entire race/bearing/seal assembly must be replaced at the same time. The bearing is encased with a rubber seal, which prevents fuel leakage and keeps the engine working smoothly. It does not impede the bearing as it turns. Ball bearings are placed in high contact areas and wear down due to friction. They need to be regularly replaced for optimal performance. If the engine shows difficulty while running, or is louder than usual, the seal or bearing may have worn down. This OEM replacement part is sourced from the manufacturer and works with certain models of Poulan small engines, including the Poulan/Poulan Pro 2900, and Husqvarna chainsaws. This part replaces parts 530019259 and 530047827, both of which are obsolete.

Piston ring seals the gap between piston and cylinder wall in small engine equipment. Replace if worn, cracked, or causing compression loss.

Secures the muffler cover to the muffler on chainsaws and small engines. Replace if screw is stripped, missing, or no longer holds the cover securely.

These ignition screws are used in the ignition systems on a variety of lawn and garden equipment. The screws are made of durable metal and fasten together different parts in the ignition system. While the screws are made of high-quality material, they can experience stress, wear and tear, and impacts that will break or damage them.To replace an ignition module screw, the garden tool will need to be disassembled. First, it should be turned off and placed on a flat surface. The spark plug wire should be disconnected before making the replacement. The ignition assembly will need to be taken apart to reach the ignition module screw. Use a screwdriver to remove the old part and replace it with a new replacement screw.This is an authentic OEM replacement component that is sourced directly from the manufacturer. The part is sold as an individual unit. Each ignition module screw is designed to be used with hedge trimmers, string trimmers, leaf blowers, edgers, and pole pruners created by Craftsman, Husqvarna, Poulan, Poulan Pro, and Weed Eater.

This starter spring is a genuine OEM replacement part for chainsaws that operate using a starter rope. When an operator pulls the starter rope out, there is a pulley around which the rope then has to recoil. The starter spring maintains tension in the pulley so that the rope will naturally recoil. The starter spring also provides enough tension to prevent the operator from yanking the rope all the way out of the assembly. Through repeated use, and especially if an operator is rough on their appliance, the starter spring can loosen up and will no longer work as effectively. When this happens, the starter pulley will not recoil and the starter rope will hang loose from the appliance. Fortunately, switching out the starter spring is an easy repair that should only require a wrench and a pair of pliers. Be careful when pulling the old spring out. Although it isn't as tense as it once was, it still has the potential to snap back. This replacement starter spring is a high-quality part for Husqvarna, Poulan, and Weed Eater appliances, and as such, it is sourced from its original manufacturer. This part does not ship with any additional hardware.

A new rope kit may be necessary if the original rope becomes deteriorated or frays with regular equipment use.This rope is part of the recoil starter assembly, an essential component that enables the motor to be pull-started. Due to frequent usage and wear and tear, the rope can easily fray. Without this rope the engine cannot be manually pull-started. It is manufactured from durable nylon.This Husqvarna rope kit is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement Husqvarna rope kit fits various different models of Husqvarna, Poulan, and Craftsman blowers, trimmers, and hedge trimmers. Please note this is sold individually. Handle grip not included.

This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.