Parts for Ge PSB9240BL2TS: Interior Parts (1) Parts

Replacement mounting bracket that secures internal panels or components to the appliance frame, restoring alignment and stability. Use this bracket to replace cracked, bent, or missing supports that cause vibration or loose parts. What it does:

• Supports and secures panels, trim, or internal assemblies to keep components properly aligned.
• Reduces rattling, sagging, or movement caused by a broken or missing bracket.
• Restores stable mounting after impact, wear, or stripped mounting points.
• Helps maintain proper fit and operation of adjacent parts by providing a solid attachment point.

• Disconnect power (and water/gas if applicable) before starting any repair.
• Basic hand tools required; remove adjacent panels or trim for access as needed.
• Retain original fasteners when possible; replace damaged clips or screws.

This shaft ring is a small retaining clip that secures a rotating shaft in place, helping keep connected components aligned and moving smoothly. It's a simple replacement that restores proper shaft retention and reduces wobble. What it does:

• Clips into a shaft groove to hold components on the shaft
• Prevents axial movement and keeps parts from sliding out of position
• Helps reduce noisy or unstable operation caused by loose shaft components
• Commonly used where a compact, reliable retention method is required

• One shaft ring

• Inspect the shaft and groove for wear or debris before installing; clean as needed
• Use appropriate snap-ring pliers or a safe, non-marring tool to install/remove the ring
• Ensure the ring fully seats in the shaft groove and the retained part is secure before reassembly
• Disconnect power and follow appliance safety procedures before servicing

This motor bracket secures the appliance motor to the housing, keeping the motor stable and aligned for reliable operation. It's a direct-fit replacement designed to restore proper motor positioning and reduce vibration or noise. What it does:

• Holds and supports the motor assembly in the correct position
• Maintains alignment between the motor and driven components (fans, pulleys, etc.)
• Reduces motor vibration and prevents contact with adjacent parts
• Faulty or cracked brackets can cause rattling noises, excessive vibration, or motor misalignment

• Install with power disconnected; follow manufacturer instructions for access and disassembly
• Use the factory mounting hardware and torque specs where specified
• Inspect surrounding mounts and fasteners; replace any worn or damaged hardware

This NTC thermistor is a temperature sensor that feeds real-time temperature data to the control. Replacing a failing sensor helps restore accurate temperature regulation, reduce nuisance shutdowns, and improve consistent cycle timing and performance.

• Monitors temperature by changing resistance as heat rises or falls
• Sends a signal to the electronic control to manage heating and fan operation
• A failed sensor can cause inaccurate temperatures, short/long cycles, or sensor-related error messages
• May prevent certain cycles from starting

• Disconnect power and allow the appliance to cool completely before servicing
• Note connector orientation and wire routing; take a photo for reference
• Install the sensor in the original location/clip and route wires away from hot or moving parts
• Restore power and run a test cycle to proper temperature response

The Thermostat is an OEM part for GE microwaves. This part regulates the temperature within the microwave, ensuring it operates within safe and efficient temperature ranges. It helps prevent overheating by monitoring and controlling the internal temperature, protecting both the appliance and the user.

Causes of a bad thermostat can include wear and tear over time, electrical malfunctions, or damage from power surges.

Symptoms of a bad thermostat include:

• Microwave not heating properly
• Overheating or shutting off unexpectedly
• Error codes related to temperature issues
• Inconsistent cooking times

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Thermostat is an OEM part for GE ovens. This critical component functions as a temperature sensor and controller within the oven, ensuring that the oven heats to the set temperature and maintains it throughout the cooking process. The thermostat prevents the oven from overheating by cycling the heat on and off as needed. 

Symptoms of a failing thermostat include:

• Oven not reaching the desired temperature
• Overheating beyond the set temperature
• Uneven cooking or baking results
• Oven temperature fluctuating more than usual

Causes of thermostat failure generally include age-related wear and tear, calibration issues, or exposure to extreme temperatures that can damage its internal components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

The Ring Assembly is an OEM replacement part for GE microwaves. It is located at the perimeter of the microwave carousel tray, providing structure and support while rotating.

Causes of a bad ring assembly can include cracking or splitting of the plastic over years of use, damage from impact with carousel edges, or loose fittings where the ring meets the turntable shaft.

Symptoms of a bad ring assembly include:

• Wobbling or asymmetry of the carousel tray during rotation
• Grating or scraping sounds from below when in use
• Difficulty smoothly rotating the food for even cooking
• Cracks or breaks that compromise the integrity of tray support

This OEM GE replacement ensures the continued balanced spinning of the microwave carousel.

This turntable shaft is the center coupler that links the microwave's turntable motor to the glass tray. Replacing a worn or cracked coupler restores smooth rotation so food heats more evenly without slips, stalls, or scraping.

• Couples the turntable motor to the tray for consistent rotation
• A worn or stripped hub can cause the tray to stop turning or turn intermittently
• Damage can lead to wobbling, slipping, or scraping noises at the center
• Loss of rotation can result in uneven cooking or cold spots

What's included: One turntable shaft Install notes:

• Disconnect power or unplug the microwave before servicing
• Remove the glass tray and roller ring; lift the old coupler straight up from the center
• Align the new coupler with the motor stem/key and press it fully into place
• Reinstall the roller ring and tray; verify smooth rotation with a microwave-safe cup of water

The Glass Tray is an OEM part for GE microwaves. This tray sits on the turntable support and rotates to ensure even cooking and heating of food.  

Common causes of a bad glass tray include accidental drops, cracks from overheating, or regular wear and tear over time. 

Symptoms of a bad glass tray include:

• Visible cracks or chips in the tray
• The tray not rotating properly
• Uneven cooking or heating of food
• The tray wobbling or not sitting securely on the turntable support

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This genuine oven rack restores interior cooking space and provides a stable, ventilated shelf for cookware. It replaces worn, bent, or missing racks so pans slide in and out smoothly for even cooking. What it does:

• Provides a sturdy support surface for cookware and bakeware
• Keeps food elevated for even air circulation and consistent baking
• Replaces damaged or warped racks that can cause uneven cooking or sticking
• Slides on existing oven rack guides for easy positioning

• Remove all oven shelves and allow the oven to cool before installing
• Slide the rack into the oven on the designated rack supports until fully seated
• No special tools required; check that the rack moves smoothly and sits level
• For safety, avoid leaning on racks or using them to support heavy loads beyond the oven's capacity

This flat metal tray is a replacement nonstick oven tray that gives you a flat cooking or drip surface for baking and roasting. It restores a level surface for pans and helps contain spills for easier cleanup. What it does:

• Provides a flat, rigid surface for baking, roasting, or catching drips beneath racks
• Restores proper fit when original tray is bent, warped, or missing
• Helps reduce food contact with oven floor and collects spills to prevent messes
• Nonstick finish eases cleanup when coating remains intact

• Install on the oven rack or support as shown in your owner's manual; ensure it sits flat before heating
• Allow tray to cool before handling to avoid burns
• Do not use abrasive pads or metal utensils on the nonstick surface to avoid damaging the coating
• Inspect coating for chips or flaking; replace if coating is compromised to avoid contamination

This nonstick metal broil pan grid provides a sturdy cooking surface for broiling, letting juices drain away for better browning and easier cleanup. Replaces worn or warped grids to restore consistent broiling performance. What it does:

• Holds food above the broil pan so heat circulates for even browning and searing
• Allows grease and drippings to drain away to reduce smoking and flare-ups
• Provides a nonstick surface to help prevent food from sticking and simplify cleanup
• Restores proper fit and stability when an original grid is bent or damaged

• Allow the oven and parts to cool completely before removing or installing the grid
• Slide the grid into the broiler pan or oven rack position as shown in your oven manual
• Clean with warm, soapy water; avoid harsh abrasives that can damage nonstick finish
• Follow all oven manufacturer safety instructions when operating the broiler

This heater holder is the mounting bracket that secures the oven heating element in place so the element stays aligned for reliable heating and safe operation. It helps prevent movement that can cause uneven cooking or damage. What it does:

• Holds and stabilizes the oven/heater element in the cavity so it stays properly positioned
• Keeps the element from contacting other components, reducing the risk of shorts or damage
• Helps maintain even heat distribution by preventing element sagging or misalignment
• Fits where the element mounts and supports normal operation of the heating circuit

• One heater holder/mounting bracket

• Turn power to the appliance off at the breaker before servicing to avoid shock
• Inspect the element and surrounding insulation for damage when replacing the holder
• Typically secures with screws or clips—retain hardware and note orientation for reassembly

This heater sheath is the metal protective tube that surrounds and secures a dryer's heating element, helping protect the element from abrasion and keeping heating airflow directed for reliable drying performance. What it does:

• Protects the heating element from contact and physical damage during operation
• Helps maintain proper airflow around the element for consistent heat distribution
• Reduces risk of element grounding or shorting caused by contact with other parts
• Can address symptoms like sputtering or uneven heating, burning/metallic smells, or visible damage to the element area

• 1 heater sheath

• Power off and unplug the appliance before service to avoid shock or injury
• Inspect the heating element and mounting hardware while replacing the sheath; replace any damaged parts
• Handle the sheath and element carefully—sharp edges may be present; wear gloves and eye protection

This insulation form kit fits the oven cavity to help retain heat and protect nearby components, restoring proper cooking performance and improving energy efficiency. It's a direct-replacement service part for affected ovens. What it does

• Replaces worn or damaged cavity insulation to reduce heat loss during baking and roasting
• Helps maintain even oven temperatures for more consistent cooking results
• Protects surrounding panels and components from excess heat
• Can reduce exterior cabinet heat and related safety concerns when properly installed

• Insulation form kit

• Disconnect power to the appliance before starting any work
• Allow the oven to cool completely to avoid burns and handle insulation with gloves
• Remove only the panels required to access the cavity; avoid compressing or tearing the insulation
• Follow OEM instructions for correct placement and securement