Parts for Lg LREL6323D/00: Introduction Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This single wiring harness connects electrical components to restore reliable power and signal routing in compatible appliances. It replaces a damaged or frayed harness to help eliminate intermittent connections and wiring-related failures. What it does

• Provides the factory-style set of wires and connectors to link control and power components.
• Restores secure electrical connections that can cause appliances to not start, lose power, or operate intermittently.
• Replaces worn, melted, or damaged wiring that create shorts or unreliable performance.
• Maintains OEM routing and connector fit to ensure proper interface with existing components.

• One single wiring harness as shown.

• Disconnect the appliance from power (and water if applicable) before servicing.
• Match connectors and wire colors; do not force connectors—verify seating and latch engagement.
• Route the harness along the original clips and channels; avoid contact with hot components or sharp edges.

This single wire harness connects controls and components to deliver power and signals so affected functions run correctly. It replaces a damaged harness to restore reliable electrical connections and consistent operation. What it does:

• Transfers power and control signals between the control board and individual components
• Restores missing or intermittent power to components when a harness is damaged
• Prevents shorts and poor connections caused by frayed wires or broken terminals
• Typical symptom: appliance or specific functions do not power up, run intermittently, or behave erratically

• Disconnect power to the appliance before starting any work.
• Match connector shapes and wire colors; seat each connector fully until it clicks.
• Route the harness following existing clips and retainers to avoid chafing or pinching.
• If terminals are corroded or connectors are damaged, replace the harness rather than attempting repairs.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

This 4.0x16mm tapping screw secures trim and internal components on compatible appliances, providing a reliable fastener for repair or reassembly. Use the correct screw to maintain fit and function during service. What it does:

• Fastens appliance panels, brackets, and small components where a self-tapping thread is required
• Replaces stripped or missing screws that cause loose panels or rattling
• Helps restore proper alignment and secure electrical or mechanical parts
• Suitable where a 4.0 x 16mm size and tapping/sharp thread are specified

• One 4.0x16mm tapping screw (quantity: 1)

• Use the matching screw location and thread engagement; do not force a misaligned fastener
• Tighten until seated; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance safety procedures before servicing
• If screws repeatedly strip, inspect mating threads or use an approved repair insert

The Range Foot is an OEM replacement part for LG electric ranges. This adjustable metal foot elevates and stabilizes the large appliance above the counter level.

Symptoms of a faulty or damaged foot include:

• Wobbling or uneven stability of the range top  
• excessive stress on internal components from improper elevation
• Possible scratches or damage to surrounding countertop surfaces

Causes typically relate to normal scratches and denting accumulated from years of transportation and positioning the heavy appliance. Constant weight exposure can deform adjustable parts.

This is a replacement door sub-assembly that restores safe access and a secure closure for your appliance door. It replaces a damaged, cracked, or worn door component to help appliances operate correctly and keep contents contained. What it does:

• Replaces the appliance door sub-assembly so the door closes and seals properly
• Restores structural support and alignment for normal opening and closing
• Addresses symptoms like a cracked or broken door, door that won't latch, or visible damage
• Works with existing hinges, latch, and seals when installed correctly

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools required; some panels or trim may need removal for access
• Follow OEM instructions for alignment and torque specs
• If the latch, hinge, or gasket is damaged, inspect and replace those parts as needed for a complete repair

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This hinge assembly lets a refrigerator/freezer door pivot smoothly and stay aligned for a proper seal. Replace a worn, bent or broken hinge to restore correct door movement and closing performance. What it does:

• Provides the pivot point that allows the door to open and close
• Restores proper door alignment and sealing when the original hinge is damaged or bent
• Reduces door sag, binding, or uneven gaps that can cause cooling issues
• Stops noisy or rough door movement caused by a failed hinge

• Unplug the appliance or disconnect power before starting any repair.
• Support the door securely (use a helper or suitable prop) before removing the old hinge to prevent injury or damage.
• Keep fasteners and mounting hardware organized; reuse existing screws unless replacements are specified.

The Main Control Board is an OEM part for LG ranges. It is the central processing unit that regulates and controls all primary heating functions. This board oversees the operation of burners, oven systems and other heating components to ensure safe and reliable performance.

Causes of a bad main control board can include failures in electronic chips or wiring due to constant heat cycling over the life of the appliance. Exposure to moisture or liquid spills could potentially damage circuitry.

Symptoms of a bad main control board include:

• Unresponsive or inaccurate heating elements
• Failure to reach or maintain set cooking temperatures
• Erratic or intermittent heating performance
• Inoperative bake/broil functions

This OEM LG part is also compatible with some Kenmore models.

The LG Range Control Panel is an OEM component specifically designed for LG brand stoves and ranges. This control panel contains the casing without the electronics. 

Causes of a bad control panel can include moisture damage over time, failure of electronic control boards or interfaces underneath, or physical breakage of components from accidental mishandling or impact. 

Symptoms of a bad control panel include:

• Knobs or buttons sticking, failing to turn, or unresponsive 
• Blank or unintelligible display readout
• Inability to turn on surface burners or oven functions

This ring guide supports and centers the microwave oven's glass turntable so it rotates smoothly for even cooking. It replaces a cracked or worn guide to reduce wobble and noisy operation. What it does:

• Centers and supports the glass tray so it turns evenly on the roller/drive assembly
• Helps keep the tray from slipping or wobbling during rotation
• Restores smooth, quiet turntable movement when the original guide is damaged
• Addresses symptoms such as a tray that wobbles, binds, or does not rotate properly

• One ring guide

• Disconnect power before servicing the appliance
• Remove the glass tray and roller assembly to access the guide
• Set the new guide into place on the turntable support/roller path and reinstall the roller and glass tray
• Handle the glass tray carefully; replace rollers or the drive coupling if worn

This rotary switch mounts behind the control knob and reads your selections on the user interface. Replacing a worn switch restores accurate, reliable knob response so the appliance recognizes the chosen setting and relays it to the control board.

• Detects the position of the selector knob and sends the appropriate signals to the main control
• Enables choosing programs/settings using the front knob
• Failure may cause unresponsive or erratic selection, settings not changing when the knob turns, or a no-start if no selection is registered
• Typically located on the back of the control panel behind the knob

• Disconnect power before servicing
• Remove the knob and access the control panel to reach the switch
• Release locking tabs or screws; transfer the wire connector in the same orientation
• Align the shaft correctly with the knob and test operation before reassembly

A rotary selector switch that restores reliable user control of cycle or function selection on the appliance control panel. Replaces a worn or faulty selector so settings register correctly when turned. What it does:

• Acts as the control interface for selecting cycles, temperatures or modes via the control panel.
• Opens and closes internal contacts as the knob is turned to change settings.
• A faulty switch can cause a knob to spin without changing the selected function, intermittent selection, or no response from the control when turned.
• Works with the existing knob and wiring harness to transmit user input to the control board.

• Always disconnect power (unplug appliance or switch off breaker) before servicing.
• Remove the control knob and mounting hardware to access the switch; note wire locations or take a photo before disconnecting.
• Handle terminal connectors carefully — avoid bending pins or pulling on wires by the insulation only.
• Test function after reconnecting power and reassembling.

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

This heater assembly replaces the dryer's heating element and housing to restore normal drying performance and consistent drum temperature. It's a direct-fit replacement designed to heat laundry when the dryer calls for heat. What it does

• Contains the heating element and support housing that generate and direct heat into the dryer drum.
• Restores heating when a failed element or damaged heater housing prevents warm air.
• Addresses symptoms such as little or no heat, clothes taking too long to dry, or intermittent heating cycles.
• Works with the dryer's thermostats and controls to provide regulated heat during operation.

• One heater assembly

• Disconnect power before starting any repair to avoid shock or injury.
• Inspect and replace related safety components if they show damage—do not assume only the heater is faulty.
• Handle the element and wiring carefully to avoid bending or breaking terminals; ensure all connections are secure before testing.

This part is the base for the small simmer burner on gas cooktops. It supports the burner cap and channels gas to the flame ports to promote consistent ignition and an even, stable flame. What it does

• Serves as the burner base for the auxiliary/simmer position
• Aligns and supports the burner cap for even flame distribution
• Routes gas from the orifice to the burner ports
• Common symptoms include weak or uneven flames, difficulty lighting with a known-good spark, or a cap that won't sit flat

• One auxiliary burner holder

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap; take out mounting screws and lift off the old holder
• Transfer/reuse the orifice, igniter electrode, gasket, and hardware as applicable; seat the new holder evenly and tighten fasteners without over-torquing
• Restore gas and power; verify proper ignition and flame

The Cooktop is an OEM part for LG ranges and cooktops. It provides the cooking surface, featuring multiple elements designed for cooking a variety of dishes.

Causes of a bad cooktop can include burners that no longer ignite properly, cracks in the glass-ceramic material, or issues with the electronic components that power the burners.

Symptoms of a bad Cooktop include:

• Burners that do not light or elements that do not heat up fully
• Loss of temperature controls for certain burners
• Thermal damage or fractures visible on the cooktop surface

This OEM LG part is also compatible with some Kenmore models.

This motor cover protects the appliance motor assembly and helps keep moving parts free from dust and debris for reliable operation. It restores the motor's protective housing after repair or replacement. What it does:

• Shields the motor and internal components from dust, lint, and light impact
• Helps maintain proper airflow around the motor to support cooling
• Reduces risk of accidental contact with moving parts for safer operation
• Restores original fit and alignment of motor mounting points

• One motor cover

• Disconnect power before beginning any repair to avoid shock or injury
• Remove outer panels and mounting hardware to access the motor area; retain fasteners for reassembly
• Confirm correct orientation and seating over the motor before securing screws
• Replace any damaged mounting tabs or fasteners to ensure a secure fit

This main electronic control board (PCB assembly) manages and coordinates your appliance's functions. Replacing a failed board can restore reliable power distribution and control of motors, valves, and other components, helping resolve no-power and erratic-operation issues.

• Directs power and timing to motors, heaters, fans, valves, and lights based on inputs from sensors and the user interface
• Interprets sensor feedback and can shut down components when faults are detected
• Failure symptoms include no power or no start, unresponsive controls or display, cycles that won't advance, intermittent shutdowns, or error codes
• May present as loads not running when commanded or visible board damage (burn marks or stuck relays)

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by the edges and avoid touching components or traces
• Photograph wiring and move connectors one at a time to the matching positions on the new board
• Secure the board and ensure all harnesses are fully seated; perform any model-specific reset/initialization per the service manual

This heater bracket is a metal mounting support that holds the appliance's heater or heating element securely in place, helping maintain proper alignment and reduce movement. Replacing a bent or broken bracket restores stable support for the heater assembly. What it does:

• Secures the heater or heating element to the appliance frame so the element stays aligned and does not contact other components.
• Prevents rattling, shifting, or sagging of the heater assembly that can cause noise or uneven heating.
• Helps maintain safe clearances between the heater and surrounding parts.
• Used when the original bracket is cracked, bent, or missing hardware.

• Disconnect power (and gas, if applicable) before beginning work to avoid electrical shock or gas hazards.
• Handle metal parts carefully — edges may be sharp. Wear gloves and eye protection.
• Match the part number and orientation, secure all fasteners, and ensure the heater is properly aligned before restoring power.

A radiant heater assembly that provides the heat source for the dryer drum so clothes dry efficiently. Replaces a worn or failed radiant heater to restore normal drying performance and cycle heating. What it does:

• Produces the infrared/radiant heat used during drying cycles
• Commonly replaced when the dryer doesn't heat or has very long dry times
• Can prevent repeated thermal cutoff trips when the heating element is faulty
• Works with the dryer's control system to cycle heat on and off as designed

• Disconnect power (and gas supply for gas models) before servicing to avoid shock or injury
• Inspect surrounding harnesses and thermal fuses; replace any damaged components
• Reassemble panels and secure all fasteners before restoring power and testing

This Radiant Surface Element is an OEM replacement part for LG electric ranges and cooktops. It is a high-power coil heating unit located below the cooktop surface that provides efficient, customizable heat for various cooking needs.

Causes of failure can be wear and damage to coiled filaments from prolonged heating cycles, cracking of ceramic insulators, or loose wiring connections suffering arcing or resistance over time.

Symptoms of a faulty element include:

• Slow or inadequate heating of cookware even on high settings
• Temperature fluctuations within the heating zone
• Burning or charring of spills and foods on the element itself
• Tripped circuit breakers obstructing range operation

This replacement is also compatible with some Kenmore models

This radiation heater is the element that delivers direct radiant heat for the microwave's grill/browning feature. Replacing a failed heater restores proper grilling performance and helps foods brown and crisp during grill or combination-cook settings. What it does:

• Supplies radiant heat for grill/browning and combo-cook modes
• Typically mounted at the top of the cavity to radiate heat downward
• Common failure symptoms: no heat in grill mode, element does not glow, poor or uneven browning
• Visual clues can include cracks, blistering, or burnt spots on the heater

• 1 radiation heater element

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a charge even when unplugged
• Access may require removing the outer case and interior shroud; beware of sharp metal edges
• Note wire positions before removal; route leads away from hot or moving parts during reassembly
• Verify secure mounts and connections before testing the grill function

The Rack is an OEM component designed specifically for LG ranges. This rack provides a surface for baking, roasting, and broiling different types of food inside the oven cavity. 

The rack is responsible for safely supporting food during the cooking process. It is constructed of durable steel with a non-stick-coated surface for easy cleaning.

Causes of a bad rack can include wear and tear over time from repeated exposure to high oven temperatures. This can cause the steel to weaken or the non-stick coating to peel. Heavy pans left on the rack may also cause dents or bends in the surface. 

Symptoms of a bad rack include:

• Sagging or uneven rack that does not lay flat 
• Warped or bent wires that no longer securely hold pans   
• Chipped or peeling non-stick coating

This OEM LG part is also compatible with Sears/Kenmore ranges. 

This fixing holder secures an internal appliance component to reduce movement and restore proper alignment. It's a small replacement bracket that helps stop rattling and keeps parts positioned for reliable operation. What it does:

• Provides a secure mounting point for the associated internal component or assembly
• Prevents movement, reducing noise, vibration, and abnormal contact
• Helps restore correct part alignment that can cause poor function when loose or broken
• Commonly replaces cracked, bent, or missing holders that allow shifting or rattling

• One holder as shown

• Disconnect power before servicing and follow all safety guidelines
• Basic hand tools typically required; remove covers or panels for access
• Inspect surrounding clips, screws, and mounts and replace any worn fasteners

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

This AC fan motor circulates air inside the refrigerator to help maintain even temperatures and efficient cooling. Replaces a failed or noisy motor to restore proper airflow and prevent warm spots or frost buildup. What it does:

• Spins the evaporator/condenser fan blades to move air across coils for cooling
• Restores airflow when the fan has stopped running or runs intermittently
• Reduces noise if the original motor is shaky, grinding, or vibrating
• Helps prevent temperature fluctuations and excessive frost/ice buildup

• Disconnect power to the appliance before attempting service
• Handle wiring and connectors carefully; note connector locations before removal
• Motor mounts and fan blade hardware may need to be reused; keep screws and brackets together
• Test operation after installation and verify correct airflow direction

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Bracket Assembly is an OEM component specifically designed for LG electric ranges utilizing rear-mount control panels. This integral assembly securely attaches the command console within the unit cabinetry.

Causes of a bad bracket can include loosening or stripped screws no longer maintaining a tight interface, impacts warping the steel base compromising flush mounting, or corrosion where dissimilar metals contact deteriorating securing points.

Symptoms of a bad bracket assembly include: 

• Loose panel unable to be properly reinstalled  
• Scratches or abrasions from rattling components
• Drooping controls suffering misaligned activation zones  
• Detached splash guard failing to fully protect surfaces

Replace yours today with this genuine OEM LG assembly to restore a robust interface. Backed mounting flanges deliver long-term stability and compatibility when replacing Samsung, Frigidaire, or GE electric ranges requiring rear console mounting as well. 

A convection fan assembly that circulates hot air inside the oven cavity to promote even baking and roasting. Replacing a worn or noisy fan helps restore consistent cooking performance and airflow in convection ovens. What it does:

• Circulates heated air for more even temperature distribution and improved browning.
• Restores proper airflow when the existing fan is noisy, loose, or failing to spin.
• Helps resolve uneven baking, hot spots, or longer cook times caused by poor air circulation.
• Works as the rotating airflow component of the oven's convection system.

• Disconnect power to the appliance before beginning any work to avoid shock risk.
• Access typically requires removing the oven interior panel or rear access panel; keep track of fasteners.
• Handle sharp sheet-metal edges and support the fan while disconnecting wiring or mounting hardware.

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

The Terminal block connect is an OEM part for LG ranges. It serves as a terminal connection point for various control boards and components within the range. The terminal block provides a secure connection hub where multiple wires can reliably transmit power and signals between electrical parts. 

Causes of a bad terminal block can include loose or corroded connections due to age, wear and tear over excessive use, or failure of electronic components it supports. 

Symptoms of a bad terminal block include:

• Intermittent or complete loss of function for certain range features  
• Electrical shorts, sparks, or unexpected shutdowns
• Inability to power on the entire appliance
• Error codes related to control boards it connects

This OEM LG part is also compatible with Sears/Kenmore ranges. 

This halogen oven lamp provides interior lighting so you can check food without opening the door. It restores clear, bright illumination for safer, easier cooking and monitoring in compatible ovens. What it does:

• Replaces a burned or flickering oven interior lamp to restore normal lighting
• Lets you view cooking progress without opening the oven door
• Helps reduce the need for extra kitchen lights when checking food
• Fits into the oven lamp socket and functions as the appliance's interior light source

• One halogen oven lamp

• Disconnect power to the appliance before servicing to avoid shock
• Allow the oven to cool fully before replacing the lamp to avoid burns
• Handle the bulb by the base or use gloves/tissue to keep oils off the glass
• Make sure the bulb is seated securely in the lamp socket before restoring power

The Broil Element is an OEM replacement part for LG electric ranges. As a vital upper heating system, this broil element helps efficiently brown and crisp foods placed directly under or on the top rack of the oven.

Causes of a defective broil element may relate to normal wear and tear on the coils from repeated high-heat cooking. Food residues adhering over time can reduce performance.

Symptoms of a problematic broil element include:

• Inadequate or uneven browning from the top-level heating system   
• Diminished functionality of the broil setting on the control panel
• Potential thermal damage or exposed wiring from a failed element

This OEM component fits some Kenmore/Sears electric range models as well. 

The Bake Element is an OEM replacement part for LG wall ovens and ranges. It is responsible for providing heat during the bake functions.

Symptoms of a bad bake element include:

• Inconsistent or unreliable bake temperatures
• Hot/cold spots leading to uneven cooking results
• Premature failure of bake cycles or overload tripping

Causes can be normal wear over thousands of heating cycles. Improper cleaning allowing residue buildup may also degrade element performance prematurely. Accurate, dependable heat is required for successful baking.

This OEM LG part is also compatible with Kenmore and Frigidaire wall ovens and ranges.

This packing gasket is the replacement door seal that helps maintain an airtight barrier to keep interior temperatures stable and prevent moisture or air leaks. Replaces a worn or damaged gasket to restore proper sealing performance. What it does:

• Seals the door opening to reduce air leaks and help maintain interior temperature
• Helps prevent moisture buildup and frost inside the compartment
• Restores correct alignment and contact where the door meets the cabinet
• Commonly replaced when the existing gasket is torn, deformed, or no longer seals evenly

• One packing gasket

• Disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the mating surface before installing the new gasket
• Work around the perimeter, pressing the gasket into the channel for an even fit; avoid stretching the gasket excessively
• If adhesive, fasteners, or clips are required, use only OEM-recommended materials and follow manufacturer guidance

The Packing Gasket is an OEM part for LG ranges. It provides a critical sealing function around the oven door, preventing heat leaks and ensuring efficient, even cooking performance. This gasket is constructed from heat-resistant materials engineered to maintain their flexible integrity even after prolonged high-temperature use.

Causes of a bad packing gasket can include drying or cracking from heat exposure over time, or damage from accidental impacts to the door seal area. 

Symptoms of a bad packing gasket include: 

• Inefficient or uneven cooking as heat escapes around the door 
• Louder noise or vibration coming from the door seal 
• Visible cracks or gaps in the gasket allow a view into the oven cavity

This OEM LG part is also compatible with electric ranges from Hotpoint, RCA, and select Kenmore models.

This front plate is the outer-facing panel that restores the appliance's appearance and protects internal components from everyday contact. It fits where the original front panel was installed and provides a finished look. What it does:

• Replaces a cracked, dented, or discolored front panel to improve appearance
• Shields controls and internal parts from dust and accidental contact
• Helps maintain proper alignment of adjacent panels and trim
• Prevents small objects from entering the appliance cavity through the front

• One front plate

• Disconnect power to the appliance before starting any work
• Remove surrounding trim or screws to access and replace the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching the finished surface during installation

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

The Rail Guide is an OEM part for LG ranges. It directs the movement of adjustable storage drawers in and out of position for easy access.

Causes relate to repeated impacts over many years of use. Heat exposure also warps metal clips holding accurate alignment.

Symptoms of a faulty drawer rail guide may include:

• Excessive noise or vibration during opening/closing
• Difficulty fully extending or retracting the drawer
• Potential for pinched fingers if collapsing edges occur

This LG part is also compatible with some Kenmore models.
 

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening