Parts for Lg LSES6338F/00: Introduction Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

The PCB Assembly Knob Light is an OEM part for LG ranges and stoves. As a component of the central control system, the PCB assembly controls the illumination beneath control knobs. It facilitates backlighting that allows for easy identification and selection of surface elements and oven functions even in low-light conditions.

Symptoms of a bad PCB assembly include:

• Control knobs not illuminating properly  
• Lights flickering or not powering on at all
• Inability to see temperature and function settings clearly

Causes of a bad PCB assembly can include moisture intrusion causing short circuits, overheating from continuous simultaneous usage of burners and oven lights, and normal wear of electronic pathways over time.

This OEM LG part is also compatible with Sears/Kenmore.

This customized screw is the exact fastener specified by the manufacturer to secure components in select LG appliances. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps maintain proper alignment over time.

• Secures panels, brackets, and internal assemblies at original mounting points
• Helps reduce vibration and rattling noises from loose hardware
• Replaces missing, rusted, or stripped screws
• Supports stable operation by keeping parts firmly in place

• Disconnect power; shut off water or gas before service
• Match the screw to the exact location using your model's parts diagram
• Start threads by hand; tighten snugly without overtightening to avoid stripping
• Use the correct driver bit for the head style to prevent damage

This 4.0x16mm tapping screw secures trim and internal components on compatible appliances, providing a reliable fastener for repair or reassembly. Use the correct screw to maintain fit and function during service. What it does:

• Fastens appliance panels, brackets, and small components where a self-tapping thread is required
• Replaces stripped or missing screws that cause loose panels or rattling
• Helps restore proper alignment and secure electrical or mechanical parts
• Suitable where a 4.0 x 16mm size and tapping/sharp thread are specified

• One 4.0x16mm tapping screw (quantity: 1)

• Use the matching screw location and thread engagement; do not force a misaligned fastener
• Tighten until seated; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance safety procedures before servicing
• If screws repeatedly strip, inspect mating threads or use an approved repair insert

This radiant heater is the dryer heating component that produces thermal radiation to warm air for efficient drying. Replacing a worn heater restores proper heat generation and helps the appliance reach normal drying temperatures. What it does

• Converts electrical energy into radiant heat to warm air inside the dryer drum.
• Restores normal drying performance when the original heater fails to produce heat.
• Common symptom linkage: no heat, low heat, or unusually long dry cycles.
• Works as the primary heat source; integrates with thermostat and safety controls.

• Disconnect power (and gas if applicable) before beginning service to avoid shock or injury.
• Handle the heater by non-heated surfaces; avoid touching exposed elements or terminals.
• Inspect surrounding components (thermostats, fuses, wiring) and replace any damaged parts.

This radiation heater is the element that delivers direct radiant heat for the microwave's grill/browning feature. Replacing a failed heater restores proper grilling performance and helps foods brown and crisp during grill or combination-cook settings. What it does:

• Supplies radiant heat for grill/browning and combo-cook modes
• Typically mounted at the top of the cavity to radiate heat downward
• Common failure symptoms: no heat in grill mode, element does not glow, poor or uneven browning
• Visual clues can include cracks, blistering, or burnt spots on the heater

• 1 radiation heater element

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a charge even when unplugged
• Access may require removing the outer case and interior shroud; beware of sharp metal edges
• Note wire positions before removal; route leads away from hot or moving parts during reassembly
• Verify secure mounts and connections before testing the grill function

This PCB power control board assembly supplies and regulates the electrical power for the appliance's control system so the unit can operate reliably. It replaces a failed power-control module to restore normal power distribution to the main control. What it does

• Converts and regulates incoming mains power for the appliance control circuitry.
• Provides power sequencing and protection for the main control board and displays.
• Common replacement when the appliance has no power, intermittent shutdowns, or no control/display response.
• Works with the main control to manage startup and safety interlocks.

• One PCB power control board assembly.

• Always disconnect mains power before servicing to avoid shock or damage.
• Handle the PCB by the edges and avoid static discharge; use an ESD wrist strap if available.
• Verify the part number on the old board matches before installation; do not force connectors.

This replacement window glass restores a clear viewing panel and completes the appliance door assembly, helping keep the interior enclosed and protecting internal components. Use it to replace cracked, broken, or fogged door glass. What it does:

• Provides a durable viewing panel so you can check inside without opening the door
• Serves as part of the door assembly to help maintain the internal environment and reduce leaks
• Replaces cracked, chipped, shattered, or fogged glass that can compromise performance or safety
• Helps protect internal components from debris and moisture entering through a damaged door

• Handle with care and wear cut-resistant gloves and eye protection; glass can break unexpectedly
• Inspect door trim, gasket, and mounting hardware; replace any damaged pieces for a proper seal
• Use basic hand tools to remove the door or access panel; avoid over-tightening fasteners

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This handle supporter is the bracket that anchors the door handle to the appliance door, keeping the handle secure and aligned. Replacing a cracked or stripped supporter restores a solid, dependable grip on the door.

• Secures the handle to the door and maintains proper alignment
• Helps fix a loose, wobbly, or detached handle
• Replaces a broken or worn mounting bracket that won't hold screws

• Disconnect power and, if applicable, shut off water before service
• Remove the handle and any trim to access the supporter and mounting screws
• Transfer or replace screws as required; do not overtighten into plastic
• Verify handle alignment and operation before fully reassembling

This Main PCB Power Control Board Assembly is the electronic control module that manages the appliance's power and user interface, restoring proper control functions and stable operation when the original board fails. What it does:

• Regulates power distribution to the appliance's systems and components
• Interprets user inputs from the control panel and runs selected cycles
• Helps stop erratic behavior like random starts/stops or unresponsive controls
• Can address failure symptoms such as no power to the unit, no display, or intermittent operation

• One Main PCB Power Control Board Assembly as shown

• Disconnect all power before servicing to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use a grounded wrist strap if available
• Verify connector fit and orientation before applying power; do not force harnesses

A replacement rotary selector switch that restores user control over cycle selection and settings. Replaces a worn or non-responsive control switch so the appliance accepts knob input and changes functions as expected. What it does:

• Serves as the user-facing control that rotates to select cycles, temperatures, or functions
• Restores electrical contact so the appliance registers knob positions and starts chosen cycles
• Commonly used when the knob spins freely, feels loose, or selected settings do not engage
• Matches the original switch's mounting and shaft orientation for a direct fit

• Disconnect power before starting any repair to avoid shock or damage
• Access may require removing the control panel—keep fasteners and small parts organized
• Handle with care to avoid bending the shaft or damaging terminals

The Lamp Cover is an OEM part for LG ranges. This part is responsible for covering and protecting the indicator light on the range console. It ensures that the indicator light is properly shielded, allowing for clear visibility and easy identification of the selected settings or functions.

A bad lens cover can occur due to damage, discoloration, or wear over time. If you notice symptoms such as a cracked or missing lens cover, diminished visibility of the indicator light, or difficulty in determining the status of the range, it may be time to replace the lens cover.

Symptoms of a bad lens cover include:

• Cracked or missing lens cover
• Diminished visibility of the indicator light
• Difficulty in determining the status of the range

Restore the function and aesthetic appeal of your LG range by replacing the damaged or worn-out lens cover with this genuine OEM part.

This LG replacement part is also compatible with Sears/Kenmore models.
 

This neon indicator lamp provides a visible signal when its circuit is energized, restoring a clear status light on the appliance's panel. Replace a failed lamp to regain quick, at-a-glance confirmation that a function is active.

• Illuminates when power is supplied to the associated circuit, serving as a panel/pilot indicator
• Helps provide clear visual status for appliance functions
• Typical symptoms: indicator does not light, is dim or flickers, stays on continuously, or shows visible damage
• Can fail open or intermittently, leading to unreliable status indication

• Disconnect power to the appliance before servicing
• Access the control/panel area to reach the lamp; note wire routing and terminal orientation
• Transfer leads and seat the lamp securely; handle components carefully to avoid damage
• If the original is board-soldered, board-level repair may be required.

This rotary switch sits behind the control knob and selects your appliance's settings. It directs power to the chosen function so the unit responds when you turn the knob, helping restore reliable, precise control. What it does

• Selects operating modes or speeds as you turn the control knob
• Routes electrical power to the correct circuit for the chosen setting
• Common failure signs: no response, only one setting works, intermittent operation, or the knob turns without detents/feels loose

• 1 rotary switch

• Disconnect power before servicing; allow any hot components to cool
• Photograph or tag each wire on the old switch; move wires one at a time to matching terminals
• Reuse mounting hardware as needed and align the shaft with the knob's flat
• Inspect connectors for heat damage; replace any compromised terminals to ensure a secure fit

This rotary switch mounts behind the control knob and reads your selections on the user interface. Replacing a worn switch restores accurate, reliable knob response so the appliance recognizes the chosen setting and relays it to the control board.

• Detects the position of the selector knob and sends the appropriate signals to the main control
• Enables choosing programs/settings using the front knob
• Failure may cause unresponsive or erratic selection, settings not changing when the knob turns, or a no-start if no selection is registered
• Typically located on the back of the control panel behind the knob

• Disconnect power before servicing
• Remove the knob and access the control panel to reach the switch
• Release locking tabs or screws; transfer the wire connector in the same orientation
• Align the shaft correctly with the knob and test operation before reassembly

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This rear cover replaces the cabinet rear panel to protect internal components and maintain proper airflow. It restores the exterior finish and keeps wiring and mechanical parts shielded from dust and damage. What it does:

• Covers and protects internal components at the appliance rear to prevent accidental contact and debris buildup
• Helps maintain proper airflow routing and component clearance behind the unit
• Restores a finished appearance to the rear of the appliance after repair or part replacement
• Useful when the original rear panel is dented, cracked, or missing

• One rear cover as shown

• Disconnect power (and water if applicable) before starting any repair
• Installation typically requires removing the old rear panel screws and securing this cover with OEM-specified fasteners
• Handle edges carefully and support the cover during installation to avoid scratching or dropping onto internal components

This LED display module is the board that illuminates the readout on your appliance's control panel. Replacing a failed module restores a clear, reliable display so you can see settings, cycle status, and alerts during operation.

• Generates the LED readout for settings, time/temperature, and status information
• Communicates with the main control to present information and fault/error codes
• Typical failure signs: blank or dead display; dim or flickering LEDs; missing segments or garbled characters; intermittent display operation

• Disconnect power to the appliance before servicing
• Use ESD precautions; handle the board by the edges and avoid touching components
• Document connector locations with photos before removal; move any model-specific brackets/light guides from the original module as needed
• After installation, restore power and verify normal display operation

The Decor Guard is an OEM part for LG range ovens. It consists of decorative trim pieces that surround the range for an aesthetically pleasing appearance.

Symptoms of a faulty decor guard include: 

• Cracks, chips, or damage appearing to enameled surfaces
• Loose, missing, or improperly aligned trim pieces 

Causes can include impact damage from cookware, repeated heating, and cooling causing materials to expand and contract, or general wear over extended use.

Replacing your LG OEM decor guard with a new set restores the pristine look and feel of the appliance. Precisely cut elements fit seamlessly to specifications while enhancing the range's overall style. This replacement is also compatible with some Sears and Kenmore models.

The Shelf Assembly is an OEM part for LG ranges. It refers to the oven racks or shelves that slide into the oven cavity, providing sturdy and level surfaces for baking, roasting, or broiling food items. This assembly typically includes multiple oven racks or shelves, designed to accommodate various cookware sizes and cooking needs.

Symptoms of a bad Shelf Assembly include:

• Racks or shelves not sliding in or out smoothly
• Excessive wobbling or instability when loaded with cookware
• Warping, discoloration, or visible damage to the racks/shelves
• Difficulty in properly securing or leveling the racks within the oven cavity

Causes of a bad shelf assembly can include prolonged exposure to high temperatures, leading to warping or discoloration. Accidental drops or impacts can also cause dents, bends, or other physical damage. Lack of proper cleaning and maintenance can contribute to the buildup of food residue or rust, affecting the assembly's functionality.

This OEM LG part is also compatible with Sears/Kenmore ranges.

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Motor, AC Fan is an OEM part for LG ovens. This fan motor is responsible for circulating air within the oven cavity, ensuring even heat distribution for consistent cooking and baking results. It helps maintain the oven’s temperature by moving hot air around, which is especially important for convection ovens.

Over time, the fan motor can wear out or become faulty due to continuous use, exposure to high temperatures, or electrical issues. When the fan motor fails, it can lead to uneven cooking and potential overheating of the oven.

Symptoms of a bad oven motor, AC fan include:

• Uneven cooking or baking results
• Unusual noises coming from the oven during operation
• The oven taking longer to preheat
• The fan not spinning or running intermittently
• Error codes related to fan or airflow issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Bracket Assembly is an OEM component specifically designed for LG electric ranges utilizing rear-mount control panels. This integral assembly securely attaches the command console within the unit cabinetry.

Causes of a bad bracket can include loosening or stripped screws no longer maintaining a tight interface, impacts warping the steel base compromising flush mounting, or corrosion where dissimilar metals contact deteriorating securing points.

Symptoms of a bad bracket assembly include: 

• Loose panel unable to be properly reinstalled  
• Scratches or abrasions from rattling components
• Drooping controls suffering misaligned activation zones  
• Detached splash guard failing to fully protect surfaces

Replace yours today with this genuine OEM LG assembly to restore a robust interface. Backed mounting flanges deliver long-term stability and compatibility when replacing Samsung, Frigidaire, or GE electric ranges requiring rear console mounting as well. 

This temperature sensor monitors internal appliance temperature and relays it to the electronic control so cycles run correctly. Replacing a faulty sensor restores accurate temperature feedback, helping the unit reach and maintain the set temperature.

• Detects temperature changes and sends a signal to the control board for proper operation
• Supports accurate heating/cooling and cycle timing based on real-time readings
• Direct replacement when the original reads open/short or out of range
• Common symptoms: incorrect temperatures, unusually long/short cycles, failure to reach set temperature, or sensor-related error codes

• Disconnect power before servicing and allow any hot components to cool
• Access the sensor, noting wire routing and connector orientation before removal
• Transfer any mounting clip/holder from the original if needed; seat the new sensor fully
• Route wiring away from moving or hot parts; restore power and run a test or cycle check

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

This replacement ring secures or positions a nearby appliance component to restore proper alignment and stable operation. It's a small but important part that helps reduce excess movement and related wear. What it does:

• Holds or locates a mating component to prevent unwanted movement or misalignment
• Helps reduce vibration and knocking noises caused by loose parts
• Restores correct spacing that maintains smooth mechanical operation
• Can prevent accelerated wear on adjacent parts when functioning properly

• Disconnect power (and water supply if applicable) before beginning any repair
• Access location may require removing panels or trim; keep fasteners organized
• Inspect surrounding parts for wear or damage and replace if needed

The Convection Fan Blade is an OEM replacement part for LG ovens. It works by circulating hot air throughout the oven, reducing cold spots and promoting consistent temperatures.

Causes of a malfunctioning Convection Fan Blade can be wear and tear from regular use, the accumulation of debris hindering the blade’s rotation, or mechanical issues impacting the fan motor or blade alignment.

Symptoms of a bad Convection Fan Blade include:

• Uneven cooking or baking, leading to partially cooked food
• Noises emanating from the oven during operation, indicating possible damage or obstruction
• The fan not rotating or moving irregularly, signaling mechanical issues

This OEM LG part is also compatible with Sears/Kenmore oven models.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

This AC synchronous motor assembly replaces the appliance's internal synchronous motor to restore smooth, reliable rotation of the designated component. It delivers direct-drive motion for components that require precise, consistent speed control. What it does:

• Spins the appliance's designated rotating component (for example a fan, blower or other driven mechanism) using a synchronous AC motor design
• Restores proper rotational motion when the original motor fails to start or maintain speed
• Helps eliminate symptoms such as no rotation, slow or intermittent movement, humming or stalled operation
• Operates at steady speed synchronized to the AC supply for consistent performance

• One motor assembly (AC synchronous), as shown

• Disconnect power before beginning any service to avoid electrical shock
• Handle the motor carefully; support the shaft and wiring during removal and installation
• Secure all fasteners and wire connections
• Test the appliance on a short cycle after installation to confirm correct operation

This heater bracket secures the dryer oven heater assembly to the cabinet, keeping the heating element stable for reliable operation and preventing rubbing or misalignment. It's a simple replacement that restores proper heater positioning. What it does

• Mounts and supports the heater assembly to keep the element in the correct position
• Prevents the heater from shifting, vibrating, or contacting other components
• Helps avoid intermittent heating caused by a loose or misaligned heater
• Works with the heater housing and mounting hardware to maintain safe clearances

• Disconnect power (unplug appliance or shut off breaker) before starting any repair
• Allow the appliance and heater to fully cool before handling
• Basic hand tools required; retain original screws and hardware
• Inspect surrounding components (wiring, insulation) while replacing; replace any damaged parts

This halogen oven lamp provides interior lighting so you can check food without opening the door. It restores clear, bright illumination for safer, easier cooking and monitoring in compatible ovens. What it does:

• Replaces a burned or flickering oven interior lamp to restore normal lighting
• Lets you view cooking progress without opening the oven door
• Helps reduce the need for extra kitchen lights when checking food
• Fits into the oven lamp socket and functions as the appliance's interior light source

• One halogen oven lamp

• Disconnect power to the appliance before servicing to avoid shock
• Allow the oven to cool fully before replacing the lamp to avoid burns
• Handle the bulb by the base or use gloves/tissue to keep oils off the glass
• Make sure the bulb is seated securely in the lamp socket before restoring power

The Heating Element is an OEM part for LG electric ranges. It serves a critical cooking function by using electric current to generate heat energy that cooks food inside the oven cavity. The heating element is constructed from flame-resistant and durable materials precisely designed to withstand high temperatures in a clean efficient manner.  

Causes of a bad heating element can include mineral deposits on coils, cracks from overheating, or general wear over extended use.

Replacing a faulty element restores dependable oven performance. 

Symptoms of a bad element include:

• Inefficient or uneven cooking temperatures
• Longer baking and cooking times 
• Cracking or sagging coils affecting heat output
• Potential safety issues if damage exposes live wires

This element also fits the heating designs used in Jenn-Air and Frigidaire electric ovens.

This hinge bracket secures and supports a refrigerator or freezer door hinge, helping the door stay aligned and operate smoothly. Replaces a worn or damaged bracket to restore proper door fit and movement. What it does:

• Provides a mounting point for the door hinge to keep the door aligned
• Prevents door sagging and uneven gaps that can affect sealing
• Reduces rattling or binding during door open/close
• Helps maintain a consistent door seal to support cooling performance

• Disconnect power (and water supply if applicable) before servicing
• Use correct tools and retain original fasteners; follow OEM torque where specified
• Support the door while removing/installing the bracket to avoid damage or injury

The Oven Door Gasket is an OEM part for LG ranges. This seal creates an insulating barrier between the hot oven interior and the external environment. The gasket ensures proper heat retention for energy efficiency and is responsible for safely containing heat inside during baking and broiling. 

Symptoms of a faulty door gasket include:

• Excessive heat loss from the oven that compromises cooking ability
• Discomfort from direct heat around the outer door surface   
• Physical damage or gaps in the insulation compromising its sealing function

Causes of gasket failure involve normal wear and tear from repetitive door openings as well as damage from oven cleaning chemicals or abrasive scrubbing.

This OEM LG part is also compatible with some Kenmore ranges featuring LG oven systems. Replacing the worn gasket restores safe, efficient oven operation.

This outer door frame secures and finishes the refrigerator/freezer door, restoring proper fit and appearance. Replaces a damaged, cracked, or warped frame to help the door seal and close correctly. What it does:

• Provides the structural trim around the door opening and anchors the door panel
• Restores proper alignment and improves door closure when the frame is warped or broken
• Prevents drafts by supporting the door gasket area
• Helps eliminate rattling or loose front panels caused by a damaged frame

• 1 outer door frame

• Disconnect power to the appliance before starting any repairs
• Remove door trim screws and panels carefully to avoid damaging the door or gasket
• Handle the frame and surrounding trim gently to prevent cracking; some clips may be brittle with age

This front panel replaces the exterior control console that houses the user interface and protects the control area. It restores a clean appearance and provides a stable mounting surface for buttons, display, and trim. What it does:

• Replaces a cracked, dented, or worn front panel that exposes internal components or looks damaged
• Provides a secure mounting surface for control buttons, display, and trim pieces
• Helps protect underlying electronics from spills, dust, and everyday wear
• Restores proper alignment and fit of the console area for consistent button access

• One front panel

• Disconnect power to the appliance before beginning work
• Remove surrounding trim and fasteners carefully to avoid scratching the finish
• Handle panel edges gently to prevent cracking; keep removed screws and clips for reassembly

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This replacement slider restores smooth, guided movement for the appliance component it mounts to, helping reduce sticking, binding and noise. A simple, low-cost part that returns parts to proper alignment and operation. What it does:

• Guides and supports a moving panel or drawer to ensure even, low-friction travel
• Reduces binding, catching or noisy movement when the original slider is worn or damaged
• Keeps the associated component aligned to prevent uneven wear or mis-tracking
• Helps restore normal operation without replacing larger assemblies

• One replacement slider

• Disconnect power to the appliance before beginning any repair
• Remove the affected panel/drawer per the appliance service instructions to access the slider
• Inspect surrounding tracks or mounting tabs for damage and replace if necessary
• Test movement after installation; if binding persists, re-check alignment

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

This replacement drawer is the OEM-style storage bin used to hold food and organize compartments in compatible refrigerators. It restores lost storage and helps keep items contained and accessible. What it does:

• Replaces a cracked, chipped, or broken drawer to restore safe storage
• Helps keep produce and packaged foods organized and contained
• Re-establishes proper fit so the drawer opens and closes smoothly
• Prevents items from falling into lower compartments when installed

• Remove all contents from the appliance and power off or unplug the unit before starting
• Slide out the old drawer and lift to disengage from tracks or supports
• Inspect slides and supports for damage; replace any worn hardware for proper operation
• Handle glass or plastic components carefully to avoid damage and wear protective gloves if needed

The Range Foot is an OEM replacement part for LG electric ranges. This adjustable metal foot elevates and stabilizes the large appliance above the counter level.

Symptoms of a faulty or damaged foot include:

• Wobbling or uneven stability of the range top  
• excessive stress on internal components from improper elevation
• Possible scratches or damage to surrounding countertop surfaces

Causes typically relate to normal scratches and denting accumulated from years of transportation and positioning the heavy appliance. Constant weight exposure can deform adjustable parts.

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening