Jenn-Air Microwave Parts

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

Molded wire clip that secures wiring and harnesses to the microwave cabinet. Replace if broken, cracked, or missing to prevent wire rubbing and chafing.

Microwave not heating but all other functions work? This magnetron thermostat protects against overheating. Easy DIY repair in under an hour.

Fix inaccurate oven temperatures or won't heat issues with this oven cavity temperature sensor. Restores precise temperature control for reliable baking.

Microwave won't heat? A faulty capacitor often causes no heating or weak performance. This high-voltage capacitor restores full power. Moderate DIY.

If your microwave runs but won't heat, a failed magnetron capacitor may be the cause. This high-voltage component stores energy for the magnetron.

A small replacement button plug that fills a control-panel or console opening and restores a finished appearance. Keeps panels sealed and prevents debris from entering unused holes. What it does:

• Covers unused control holes or mounting openings on consoles and panels
• Helps block dust, moisture, and grime from entering appliance internals
• Restores a consistent, finished look to the control surface
• Useful when a damaged or missing plug leaves an exposed opening

• One button plug (black)

• Typically snaps into place from the front of the panel; no special tools usually required
• Ensure the cavity is clean and free of debris before installing for a secure fit
• If the plug sits near electrical components, disconnect power to the appliance before servicing
• Verify fit against the opening before final installation; slight trimming is not recommended unless specified

Fix a microwave that won't heat or runs inconsistently. This temperature sensor monitors internal heat levels to regulate cooking performance.

Lower cabinet base for microwaves. Provides structural support and stabilizes the unit. Replace if cracked, damaged, or warped to restore level positioning.

Microwave light reflector directs bulb illumination inside cooking cavity. Replace if cracked, discolored, or missing to restore proper lighting. Confirm fit with your model number.

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed

Microwave not heating food? The high voltage transformer powers the magnetron. Common when you smell electrical burning or unit stops working.

This tension spring restores proper movement and tension for the appliance component it secures, helping the part operate smoothly and reliably. It's a simple replacement that fixes common issues caused by worn or broken springs. What it does:

• Provides tension to hold or return a moving component to its correct position
• Helps stop sagging, slipping, or loose operation of doors, latches, or levers
• Can reduce rattling or unusual noises caused by a failed spring
• Restores normal mechanical action when the original spring is stretched or broken

• Disconnect power to the appliance before starting any repair
• Springs can be under tension—use appropriate tools and wear eye/hand protection
• Compare the new spring to the old one for length, coil size, and end fittings before installation