Jenn-Air Refrigerator Wire, Harness, Power Cord

Replacement power cord that restores the electrical connection so your appliance receives safe, consistent power. Use this cord to replace frayed, damaged, or non-functioning cords and help return reliable operation to the appliance. What it does:

• Restores the appliance's main power connection so it can turn on and operate.
• Commonly used when a cord shows frayed insulation, exposed wires, scorch marks, or intermittent power.
• Can address issues where the appliance does not power on due to a broken or damaged cord.
• Replaces cords with loose or damaged plug/terminal connections that may cause sparking or overheating.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord.
• Verify the cord configuration (3-prong vs. 4-prong) and terminal type match your appliance and local electrical code before installation.
• Use proper strain relief and routing to prevent pinching; secure all connections and replace any damaged terminal hardware.

This wire harness is a factory-style replacement assembly that restores electrical connections between appliance components for reliable operation and diagnostics. It helps reestablish power and signal paths to controls, motors, lights, and sensors. What it does:

• Replaces damaged or frayed wiring to restore electrical continuity and reduce intermittent faults
• Connects control board, motors, lights, and sensors so components can receive power and signals
• Helps stop symptoms such as loss of lights, unresponsive controls, or intermittent motor operation
• Provides the correct connector fit and wire routing to match factory configuration

• Always disconnect power to the appliance before inspecting or replacing wiring
• Compare the new harness to the original and route connectors the same way to avoid pin mis-matches
• Secure harness with existing clips or fasteners; do not pinch or excessively bend wires

This wire harness routes power and signals between an appliance's control and electrical components to restore reliable connections and operation. Use it to replace a damaged or frayed harness that is causing power or control issues. What it does:

• Re-establishes secure electrical connections between controls, motors, switches and sensors
• Routes and organizes multiple wires to prevent shorts and chafing
• Replaces burned, frayed or broken wiring that can cause intermittent operation
• Helps resolve symptoms like no power to controls, unit not starting, or inconsistent function

• Disconnect all power (unplug or switch off circuit breaker) before servicing
• Label or photograph connector locations before removal to ensure correct reassembly
• Route harness to avoid pinch points and secure with original clips or ties
• Replace the harness and inspect mating components if you see melted connectors or damaged terminals

This power cord service assembly replaces a damaged or worn external cord to restore a safe electrical connection to the appliance. Designed as a direct-replacement assembly for service repairs, it helps return reliable power delivery. What it does:

• Provides the external electrical connection between the appliance and wall outlet
• Replaces frayed, cut, or damaged cords that can cause intermittent power or unsafe conditions
• Helps resolve issues where the appliance does not power on due to cord damage
• Restores proper strain relief and secure wiring at the appliance entry point

• Always disconnect power at the breaker or unplug the appliance before servicing
• Route the cord and secure strain relief per the appliance's service instructions

This genuine replacement wire harness connects and routes power and signals between components to restore proper electrical function and safe operation. Designed to match original wiring layout for a straightforward repair. What it does:

• Replaces a damaged or burned wiring harness to restore electrical continuity
• Restores power/signal paths that can stop intermittent operation or failures
• Helps eliminate arcing, shorts, or loss of function caused by frayed or broken wires
• Maintains correct routing to prevent chafing and overheating when installed correctly

• Disconnect all power (unplug appliance or switch off breaker) before starting work
• Handle connectors by the plug body, not the wires; ensure secure, full seating of terminals
• Route harness along original clips and channels to avoid pinch points or hot surfaces
• Replace any connector, terminal, or mounting hardware that is missing or damaged before powering on

This wire harness is the factory-style electrical assembly that routes power and signals between components to restore reliable operation. It replaces damaged or worn wiring and connector assemblies responsible for intermittent or lost power. What it does:

• Carries electrical power and control signals between appliance components
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation
• Resolves symptoms such as the appliance failing to start, erratic control behavior, or intermittent power to components
• Ensures connectors are properly routed and joined to prevent shorts and unreliable connections

• Disconnect power (unplug appliance or switch off circuit breaker) before you begin
• Handle connectors gently; match connector shapes and pin counts before seating
• Route the harness following factory clips and channels to avoid heat or pinch points

This wire harness routes power and signals between the appliance control and key components so the unit can operate correctly. Replacing a damaged harness restores reliable electrical connections and helps eliminate intermittent faults. What it does:

• Carries power and control signals between the main control, motors, switches, sensors and other components
• Restores proper electrical connectivity when wires are frayed, burned, or connectors are loose
• Can stop intermittent operation, components that don't receive power, or erratic control behavior
• Helps prevent electrical arcing or shorts caused by damaged wiring

• One wire harness as shown

• Always disconnect power (unplug or switch off circuit breaker) before beginning service
• Inspect connectors and wire terminals for corrosion or damage; match connector orientation during reassembly
• Replace only with the exact harness for your appliance model to ensure correct fit and wiring

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement power cord restores electrical connection to the appliance, providing a safe and reliable feed when the original cord is damaged or worn. It's a direct-fit wiring component meant for like-for-like replacement. What it does:

• Delivers AC power from the wall outlet to the appliance so it can operate.
• Replaces cords that are frayed, cut, melted, scorched, or have exposed wiring.
• Helps stop intermittent power, arcing at the plug, or appliances that won't power on due to cord damage.
• Works with the appliance's factory power inlet and strain-relief system when installed correctly.

• One replacement power cord.

• Always disconnect power at the breaker and unplug the appliance before installing.
• Match this cord to the appliance's original cord and connect using the existing terminals or connector; do not splice or alter wires.
• Use the proper strain relief and secure the cord to prevent pulling or chafing.