Jenn-Air Wire, Harness, Power Cord

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This replacement dryer power cord supplies electricity from your wall outlet to the dryer's terminal block, providing a secure, reliable connection. Replace a worn or damaged cord to restore dependable power and reduce risk of intermittent shutoffs.

• Supplies electrical power from the outlet to the dryer
• Provides a secure connection at the plug and the dryer's terminal block when properly installed
• Common fixes: dryer won't power on, power cuts out when the unit is moved, or visible damage/heat discoloration on the cord or plug
• Replace if prongs are loose or the insulation is cracked or melted

• Disconnect power at the breaker before servicing and verify the outlet is de-energized
• Follow the dryer's wiring diagram; connect conductors to the correct terminals and tighten securely
• Use an approved strain relief/clamp per the dryer instructions and local electrical codes

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

Replacement power cord that restores the electrical connection so your appliance receives safe, consistent power. Use this cord to replace frayed, damaged, or non-functioning cords and help return reliable operation to the appliance. What it does:

• Restores the appliance's main power connection so it can turn on and operate.
• Commonly used when a cord shows frayed insulation, exposed wires, scorch marks, or intermittent power.
• Can address issues where the appliance does not power on due to a broken or damaged cord.
• Replaces cords with loose or damaged plug/terminal connections that may cause sparking or overheating.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord.
• Verify the cord configuration (3-prong vs. 4-prong) and terminal type match your appliance and local electrical code before installation.
• Use proper strain relief and routing to prevent pinching; secure all connections and replace any damaged terminal hardware.

This wire harness is a factory-style replacement assembly that restores electrical connections between appliance components for reliable operation and diagnostics. It helps reestablish power and signal paths to controls, motors, lights, and sensors. What it does:

• Replaces damaged or frayed wiring to restore electrical continuity and reduce intermittent faults
• Connects control board, motors, lights, and sensors so components can receive power and signals
• Helps stop symptoms such as loss of lights, unresponsive controls, or intermittent motor operation
• Provides the correct connector fit and wire routing to match factory configuration

• Always disconnect power to the appliance before inspecting or replacing wiring
• Compare the new harness to the original and route connectors the same way to avoid pin mis-matches
• Secure harness with existing clips or fasteners; do not pinch or excessively bend wires

This wire harness routes power and signals between an appliance's control and electrical components to restore reliable connections and operation. Use it to replace a damaged or frayed harness that is causing power or control issues. What it does:

• Re-establishes secure electrical connections between controls, motors, switches and sensors
• Routes and organizes multiple wires to prevent shorts and chafing
• Replaces burned, frayed or broken wiring that can cause intermittent operation
• Helps resolve symptoms like no power to controls, unit not starting, or inconsistent function

• Disconnect all power (unplug or switch off circuit breaker) before servicing
• Label or photograph connector locations before removal to ensure correct reassembly
• Route harness to avoid pinch points and secure with original clips or ties
• Replace the harness and inspect mating components if you see melted connectors or damaged terminals

This power cord service assembly replaces a damaged or worn external cord to restore a safe electrical connection to the appliance. Designed as a direct-replacement assembly for service repairs, it helps return reliable power delivery. What it does:

• Provides the external electrical connection between the appliance and wall outlet
• Replaces frayed, cut, or damaged cords that can cause intermittent power or unsafe conditions
• Helps resolve issues where the appliance does not power on due to cord damage
• Restores proper strain relief and secure wiring at the appliance entry point

• Always disconnect power at the breaker or unplug the appliance before servicing
• Route the cord and secure strain relief per the appliance's service instructions

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This genuine replacement wire harness connects and routes power and signals between components to restore proper electrical function and safe operation. Designed to match original wiring layout for a straightforward repair. What it does:

• Replaces a damaged or burned wiring harness to restore electrical continuity
• Restores power/signal paths that can stop intermittent operation or failures
• Helps eliminate arcing, shorts, or loss of function caused by frayed or broken wires
• Maintains correct routing to prevent chafing and overheating when installed correctly

• Disconnect all power (unplug appliance or switch off breaker) before starting work
• Handle connectors by the plug body, not the wires; ensure secure, full seating of terminals
• Route harness along original clips and channels to avoid pinch points or hot surfaces
• Replace any connector, terminal, or mounting hardware that is missing or damaged before powering on

This replacement power cord restores electrical connection to the appliance, providing a safe and reliable feed when the original cord is damaged or worn. It's a direct-fit wiring component meant for like-for-like replacement. What it does:

• Delivers AC power from the wall outlet to the appliance so it can operate.
• Replaces cords that are frayed, cut, melted, scorched, or have exposed wiring.
• Helps stop intermittent power, arcing at the plug, or appliances that won't power on due to cord damage.
• Works with the appliance's factory power inlet and strain-relief system when installed correctly.

• One replacement power cord.

• Always disconnect power at the breaker and unplug the appliance before installing.
• Match this cord to the appliance's original cord and connect using the existing terminals or connector; do not splice or alter wires.
• Use the proper strain relief and secure the cord to prevent pulling or chafing.

This wire harness is the factory-style electrical assembly that routes power and signals between components to restore reliable operation. It replaces damaged or worn wiring and connector assemblies responsible for intermittent or lost power. What it does:

• Carries electrical power and control signals between appliance components
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation
• Resolves symptoms such as the appliance failing to start, erratic control behavior, or intermittent power to components
• Ensures connectors are properly routed and joined to prevent shorts and unreliable connections

• Disconnect power (unplug appliance or switch off circuit breaker) before you begin
• Handle connectors gently; match connector shapes and pin counts before seating
• Route the harness following factory clips and channels to avoid heat or pinch points

This wire harness assembly routes power and signals between major components to restore electrical connection and reliable operation. It replaces a damaged or frayed harness to help eliminate intermittent power, no-starts, or lost control functions. What it does:

• Connects power and control circuits between the main control and other components
• Restores reliable electrical continuity when wiring is damaged, burned, or corroded
• Helps resolve symptoms such as intermittent operation, appliances that won't start, or components that receive no power
• Prevents shorting or arcing caused by exposed or broken wires when properly installed

• Disconnect the appliance from power (unplug or turn off the circuit breaker) before beginning work
• Handle connectors gently; match keyed connectors when reassembling to avoid miswiring
• Inspect mating terminals and housings for damage; replace if terminals are burned or corroded

This multi-wire electrical harness routes power and signals between appliance components to restore reliable connectivity and control. Replacing a damaged harness helps stop intermittent operation and prevents wiring shorts or lost function. What it does:

• Carries power and control signals between components such as controls, motors, sensors, or switches
• Restores electrical continuity when original wiring is frayed, cut, or burned
• Helps stop intermittent operation, no-start conditions, or component failures caused by damaged wiring
• Prevents potential short circuits from exposed or chafed wires

• Disconnect power before starting — always follow lockout/tagout procedures
• Replace harness using routing and connector orientation
• Inspect mating connectors and terminals; do not use if corrosion or damage is present
• Securely fasten harness with existing clips/ties to avoid rubbing or heat exposure

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed