Kelvinator Refrigerator Screws, Nuts, Washers

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

This replacement screw features a #10-32 machine thread and 3/4-inch length to securely fasten brackets, panels, and other components. Restore a tight, rattle-free fit by replacing missing or stripped hardware during repairs or reassembly. What it does:

• Secures panels, brackets, trim, and other mounted parts
• Replaces missing, rusted, or stripped screws that no longer hold
• Helps reduce vibration and rattling from loose components
• Maintains proper alignment and stability after service

• One screw (#10-32 x 3/4)

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the old screw and inspect receiving threads for damage
• Start by hand to avoid cross-threading; use the correct driver and do not overtighten (especially into plastic)

• Thread: #10-32 (machine)
• Length: 3/4 inch

The insert nut provides a durable threaded anchor in thin metal or plastic panels. It lets mounting screws tighten securely so covers, brackets, or trim stay fastened and aligned without loosening from vibration.

• Adds internal threads in a thin panel so a machine screw can be used
• Secures panels, brackets, or trim to the appliance cabinet or frame
• Replaces a stripped, damaged, or missing insert to restore screw retention
• Symptoms addressed: screws won't tighten, hardware falls out, panel rattles or shifts

• Disconnect power to the appliance before servicing; shut off water or gas supply if applicable
• Access the mounting location; remove the screw and the old insert if present
• Position the new insert squarely in the hole/slot and press or snap into place as designed
• Reinstall the screw and tighten snugly—do not overtighten to avoid stripping the insert or panel

This replacement mounting screw secures internal parts and panels on compatible Frigidaire appliances, restoring proper fit and reducing rattles or loose components. Simple hardware that helps keep assemblies aligned and stable. What it does:

• Fastens panels, brackets or small components to maintain appliance integrity
• Replaces missing or stripped screws that cause loose panels or vibration noise
• Restores secure connections after repairs or part replacements
• Helps prevent further wear caused by loose assemblies

• One replacement mounting screw as shown

• Disconnect power before working on electrical appliances; follow the manufacturer's safety guidelines
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to parts or threads
• If screw threads or mating hole are damaged, replace with correct hardware.

A replacement hex nut that secures threaded fasteners on Frigidaire appliances. This small but essential hardware restores proper attachment of panels, brackets, and components so parts stay tight and appliances run quietly. What it does:

• Secures components by threading onto matching bolts or studs to hold panels, trim, brackets, or assemblies in place
• Stops loose or rattling panels caused by a missing or worn nut
• Maintains proper alignment of attached parts to prevent vibration-related wear
• Simple, low-profile fastener used across multiple internal and external appliance locations

• Disconnect power to the appliance before starting any repair
• Use the correct-size wrench or socket and tighten snugly; avoid overtightening to prevent stripping threads
• If the original stud or bolt is damaged, replace that component as well for a reliable repair

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

This replacement screw fastens appliance panels and components to restore a secure fit and reduce vibration or rattling. Use when original hardware is missing, loose, or stripped to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets, and trim to prevent movement and rattling.
• Replaces missing or damaged hardware that can cause loose or misaligned parts.
• Helps maintain proper component alignment for reliable operation.
• Small but essential fastener for safe, stable assembly.

• Disconnect power before servicing any electrical appliance.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten, which can strip threads or crack panels.
• Keep removed hardware organized to ensure correct reinstallation.