Kenmore / Sears Freezer Gasket & Seal

The Evaporator Cover Gasket seals the perimeter of the freezer's evaporator cover to prevent air leaks that can lead to frost, moisture, and temperature swings. Replacing a worn gasket helps restore proper airflow and consistent cooling.

• Seals the evaporator cover to the liner to maintain directed airflow and contain cold air
• Helps prevent frost or ice buildup around the cover and on nearby air passages
• Can help address symptoms like temperature inconsistencies, poor cooling, or excess moisture caused by air leaks
• Replaces a torn, flattened, or missing gasket to ensure a tight cover fit

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the evaporator cover to access the gasket
• Clean mating surfaces; press the new gasket fully into place with no gaps or twists
• Ensure air vents are unobstructed, reinstall the cover securely, then restore power

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

The Door Gasket is an essential OEM component for Frigidaire top-freezer refrigerators. It establishes an insulating air seal around the perimeter of the refrigerator and freezer doors.

Causes of failure include breakdown of sealing materials from prolonged compression during repeated closure stresses. Damage like cracks or tears diminish gasket capabilities over time.

Symptoms of a faulty door gasket include: 

• Cool air leakage resulting in warmer interior temperatures
• Frost or condensation buildup visible around door frames
• Physical deterioration like tearing or perishing gasket materials

This OEM Frigidaire replacement gasket is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This door gasket is a replacement refrigerator door seal that helps maintain an airtight closure to keep cold air in and reduce temperature fluctuations. Restores proper sealing to help the fridge run efficiently and protect food. What it does:

• Seals the refrigerator door to prevent warm air from entering and cold air from escaping
• Helps reduce frost buildup and uneven cooling caused by a failing seal
• Can lower strain on the compressor by improving temperature stability
• Addresses symptoms such as visible gaps, drafts, or moisture buildup around the door

• Disconnect power to the appliance before starting any work
• Clean and dry the door frame surface before installing the new gasket for a tight seal
• Remove the old gasket carefully; use hand tools and avoid sharp implements that could damage the cabinet
• Follow the appliance manufacturer's installation instructions for proper fit and tab alignment

The Gasket is an OEM part for Frigidaire refrigerators. It forms a seal around the refrigerator or freezer door, preventing warm air from entering and cold air from escaping, thus maintaining the optimal internal temperature and ensuring energy efficiency. This gasket measures approximately 40.62" x 21.12". 

Common causes of a bad gasket include frequent use, exposure to spills, or wear and tear over time. A compromised gasket can lead to temperature fluctuations and increased energy consumption.

Symptoms of a bad gasket include:

• The door not sealing properly
• Increased frost buildup inside the refrigerator or freezer
• Warmer than usual temperatures inside the appliance
• Higher energy bills due to the refrigerator working harder to maintain cool temperatures

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Gasket is an OEM part for Frigidaire freezers. This gasket forms a seal around the door, ensuring that cold air stays inside while keeping warm air out.  

Causes of a bad gasket can include regular wear and tear from frequent opening and closing of the door, exposure to extreme temperatures, and physical damage from impacts.

Symptoms of a bad door gasket include:

• Frost buildup around the door edges
• Increased freezer temperature or inconsistent cooling
• Excessive energy consumption
• The door not sealing properly or appearing misaligned

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement part is a door gasket, and it is intended for use in refrigerators and freezers. This is a genuine replacement part made by Frigidaire. This gasket is an important part of any fridge or freezer. This part is used around the lining of the fridge doors so that the appliance is sealed shut when not in use. This is important so that the cool air stays inside and is able to keep the food and other items at the correct temperature. A new gasket lining might be needed if the current one is visibly falling off or not attached any longer. The gasket might have a leak or be coming apart at different areas on the appliance. Simple check around the lining of the gasket to check if there are any visible gaps. If the appliance is not staying at the correct temperature it can also be because the gasket is not connected properly.No special tools should be needed for this repair as the user should be able to simply attach the gasket around the appliance. Note that this is a genuine OEM replacement part and is told individually.