Kenmore / Sears Freezer Touch Pad

The Electrical Control is an OEM part compatible with Frigidaire upright freezers. As the primary processing board, it monitors all freezer functions including temperature, fans, lighting, and door sensors. A faulty control compromises dependability.

Symptoms of a bad control include:

• Inconsistent or fluctuating interior temperatures  
• Failure of lights or other electrical accessories
• Poor fan or defrost performance issues
• Error codes displayed on control panels

Causes can be water intrusion disrupting circuits, dust buildup over many years of operation, or typical wear over time.  

This Frigidaire OEM part fits Electrolux, Gibson, Danby and select Kenmore models for a factory-accurate replacement that preserves reliability.

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine OEM part is a control display unit for freezers. The control display unit is the part that houses the digital display and buttons for the freezer settings. It displays the temperature of the freezer. Over time, a control display can become damaged due to excessive wear and tear. If the screen is cracked or the buttons are no longer operating, then the control display unit will need to be replaced.To replace this part, start by unplugging the freezer. Once it has been powered off, proceed to pry the display unit out from the freezer using a flat head screwdriver or putty knife. Gently pull up until it is released from its mounting brackets. After removal, take the new unit and snap it into its brackets, making sure it is securely in place. Restore power to the appliance.This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand freezers.

The Freezer Control Board is an OEM part for Frigidaire freezers. It manages and regulates the various functions of the freezer, including temperature control, defrost cycles, and compressor operation. This control board ensures that the freezer maintains the correct temperature and operates efficiently.

Over time, the freezer control board can fail due to electrical surges, component wear, or manufacturing defects. When the control board malfunctions, it can disrupt the overall performance of your freezer, leading to inconsistent freezing and other operational issues.

Symptoms of a bad freezer control board include:

• The freezer not maintaining the correct temperature
• The freezer running continuously or not running at all
• Unresponsive control panel or error codes displayed
• Irregular defrost cycles causing ice buildup

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is the electronic control board that governs the appliance's cooling system. It interprets sensor input and user settings to run key components, helping maintain consistent temperatures when the original controller becomes faulty or erratic.

• Monitors temperature sensor feedback and executes cooling cycles to hold the selected setpoint
• Controls major components on applicable models
• May manage additional functions like defrost timing or alarms depending on model design
• Failure can present as warm or unstable temperatures, unit not starting, short-cycling/running constantly, or unresponsive temperature adjustments

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Note wire/plug locations; transfer connectors to the new board one at a time
• Secure the board in its mounting and ensure all harnesses are fully seated
• Reassemble covers/panels before restoring power and checking operation

This electronic control board is the freezer's central control module. It processes sensor inputs and user settings to run the cooling system and alerts. Replacing a failed board helps restore reliable operation and accurate temperature management. What it does:

• Controls compressor and evaporator fan operation to maintain the set temperature
• Interprets thermistor input and applies control logic to regulate cooling
• Coordinates features such as alarms and, on electronic models, defrost cycles
• Common symptoms include the unit not running or powering up, warming or unstable temperatures, unresponsive or erratic controls/display, or excessive frost buildup

• Disconnect power before servicing; handle the board with ESD precautions
• Access the control housing, note wire locations, and transfer connectors one at a time
• Secure the replacement board and reuse original mounting hardware and any reusable trim/overlay as applicable
• Restore power, set temperatures, and allow up to 24 hours for stabilization

Restore accurate cooling and responsive controls with this Electronic Control Board. It monitors sensors and user settings to manage your freezer's key operations so the unit reaches and maintains the temperature you choose.

• Regulates cooling by commanding the compressor and evaporator fan to maintain set temperature
• Interprets thermistor and keypad inputs to execute temperature changes
• Coordinates defrost timing and temperature alarm functions on applicable models
• Symptoms it may address: not cooling or overcooling, runs constantly or won't run, erratic/inaccurate temperature display, beeping alarm, unresponsive buttons or display

• Disconnect power before servicing; handle the board by its edges and use ESD protection
• Note/photograph wiring before removal; transfer any reusable mounting brackets or covers
• Ensure all connectors are fully seated and locked
• After installation, set your desired temperature and allow up to 24 hours for temperatures to stabilize

This part is a control board that is manufactured for use on freezers. This component manages the functions of the freezer, including the temperature settings and the defrost cycle time. It features a digital display and well as buttons to control each setting.When the control board only works intermittently, it is time to replace it before it completely stops working. The display may stop working or will blink on and off. The replacement process is very easy and only takes about 5 minutes to complete. It simply snaps in and out. The person performing the repair may find a wide putty knife handy to push in the two clips on each side. Unplug the freezer before replacing this part.This particular control board is compatible with freezers that are manufactured by Frigidaire, Kenmore, and Electrolux. It is sold individually. This part is sourced straight from the manufacturer as a genuine OEM replacement part.

This electronic control board replaces the refrigerator's main control module to restore reliable control of temperature, defrost, and compressor cycles. It fixes intermittent or non-responsive controls for better cooling performance and consistent operation. What it does:

• Receives user inputs and manages compressor, fans, and defrost timing to maintain set temperatures
• Controls display and status indicators so settings and alarms register correctly
• Stops erratic cycling and resolves symptoms like no cooling, unresponsive buttons, or blinking lights
• Helps correct error codes caused by failed or intermittent control signals

• One electronic control board (main control)

• Disconnect power to the appliance before starting work to avoid electrical shock
• Handle the board carefully; avoid touching contacts and use proper ESD precautions when possible
• Compare part number on the old board to ensure correct replacement before installing