Kitchenaid Cooktop Knob, Dial & Button

LF, LR, RR Stainless

Black

Restore precise control with this replacement control knob. It mounts on the control shaft so you can smoothly select settings again, replacing a cracked, stripped, or missing knob and bringing back a clean, finished look.

• Attaches to the control shaft to select temperature, power level, or cycle
• Common fix for knobs that crack, strip, wobble, or fall off
• Restores positive engagement so the control turns as intended
• Helps maintain consistent operation and an intact user interface

• Disconnect power and shut off gas/water if applicable before servicing
• Pull the old knob straight off; avoid prying against the console
• Align the flat side or splines of the shaft and press the new knob on firmly until seated
• Verify smooth rotation and proper engagement after installation

Replacement control knob restores easy, accurate operation of your appliance's control panel. Fits the factory control shaft to replace cracked, loose, or worn knobs so you can select settings with a secure grip and clear markings. What it does:

• Replaces a damaged, cracked, or missing control knob so functions can be selected reliably.
• Provides a secure grip and clear position indication for precise setting selection.
• Commonly used when the original knob spins on the shaft, is loose, or has worn-off markings.
• Intended to match the appliance's original control mounting.

• Disconnect power to the appliance before removing or installing the knob.
• Most knobs simply pull straight off the control shaft; align the new knob and push on until fully seated.
• If the knob is held by a screw or retaining clip, save the hardware and refer to the owner's manual for removal specifics.
• If the control shaft is damaged, repair or replace the underlying control assembly before installing the new knob.

The Knob Bezel is an OEM Replacement Part designed for Whirlpool cooktops. This part is located behind the burner knob and serves the crucial role of labeling different burner settings. 

Causes of a bad bezel-knob can include regular wear and tear, accidental impacts, or exposure to heat and cleaning chemicals. Over time, the bezel may crack, discolor, or become loose.

Symptoms of a bad bezel-knob include:

• Cracks or breaks in the bezel
• The bezel becoming loose or falling off
• Discoloration or fading
• Difficulty in turning the control knobs due to misalignment

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A replacement rubber grommet for Whirlpool appliances that cushions and seals openings to protect hoses and wiring from chafing and wear. Restores a snug seal to help reduce leaks, noise, and vibration damage. What it does:

• Cushions and protects wiring, hoses and components where they pass through panels or housings.
• Forms a sealing barrier to help reduce moisture intrusion and small leaks.
• Helps prevent abrasion and wear that can lead to frayed wires or hose damage.
• Common signs it's needed: visible cracking, deformation, or rubbing at an opening.

• Disconnect power (and water/gas where applicable) before servicing the appliance.
• Verify correct location and orientation; press the grommet into the opening until fully seated.
• Use a little mild soap or silicone lubricant to ease installation if tight; avoid petroleum-based solvents.

Replacement control knob for select Whirlpool appliances that restores safe, reliable operation of the control shaft. Replace a cracked, stripped or missing knob so you can accurately select cycles, temperatures or functions. What it does:

• Snaps onto the control shaft to let you turn and set appliance functions or temperature settings.
• Replaces knobs that are cracked, melted, stripped, loose or missing and no longer provide positive engagement.
• Restores the indicator pointer so you can clearly see the selected setting.
• Compatible with matching splined control shafts.

• Always disconnect power (unplug or shut off breaker) before servicing controls.
• Pull the old knob straight off the shaft; align the replacement's indicator with the shaft flat/spline and push on firmly until seated.
• If the knob won't seat or turns loosely, inspect the control shaft for damage—replace the switch or shaft assembly if needed.

Color: black. Measures about 2 inches in diameter.

This replacement gas control knob restores smooth, precise burner adjustment and refreshes the look of your range or cooktop. The almond finish matches original styling for a clean, uniform appearance on compatible gas models.

• Attaches to the surface burner valve stem to control gas flow and flame height
• Common fix for a cracked, stripped, wobbly, or missing knob
• Helps when the pointer no longer aligns or the knob is hard to turn
• Cosmetic refresh for discolored or worn knobs

• Ensure all burners are OFF and the appliance is cool before servicing
• Pull the old knob straight off the valve stem; do not pry against the panel
• Align the new knob with the stem and press straight on until fully seated
• If the knob will not seat, inspect the stem for damage and do not force installation

This is a control knob for select cooktops/ranges. It lets you set burner heat levels by turning the surface valve shaft. Replacing a worn or cracked knob restores accurate control and a clean, finished look.

• Attaches to the burner control valve stem to adjust flame/heat
• Worn splines or a cracked hub can cause the knob to slip or not turn the valve
• Cosmetic damage or missing knob can make settings hard to read or select
• Stiff, loose, or non-responsive operation can indicate the knob needs replacement

• Disconnect power and allow all surfaces to cool before servicing
• Pull the old knob straight off the valve stem; avoid twisting the stem
• Align the new knob's insert with the flat on the valve shaft, then press firmly
• Test each position for smooth operation before use

This replacement control knob restores a worn or damaged gas range control interface so you can safely and accurately adjust burner/oven settings. It gives a secure grip and reliable rotational control for normal operation. What it does:

• Fits onto the gas control shaft to allow manual selection of burner or oven settings.
• Restores proper tactile feel and alignment when the original knob is cracked, stripped, or missing.
• Helps prevent accidental slips or imprecise adjustments that make flame/temperature control difficult.
• Common symptom: knob spins, won't engage the valve, or is physically broken and cannot be used.

• Turn off gas supply and electric power to the appliance and allow all surfaces to cool before attempting replacement.
• Remove the old knob by pulling it straight off the control shaft; align the new knob to the splines and push it firmly into place.
• Do not force the knob if it doesn't seat smoothly; double-check alignment.

This control knob replaces a damaged or missing range/oven control knob to restore safe, reliable control of temperature and cooking settings. It provides a secure grip and direct engagement with the control shaft for accurate adjustment. What it does:

• Fits onto the appliance control shaft to select temperature, burner or oven settings
• Restores grip and tactile feedback when the original knob is cracked, stripped or missing
• Prevents accidental setting changes caused by a loose or damaged knob
• Works with split-shaft or D-shaft style controls depending on your original knob design

• Pull-off style: firmly pull the old knob straight off the control shaft; push the replacement knob on until fully seated
• Verify shaft type and alignment before forcing the knob onto the control; do not hammer or over-torque
• Disconnect power or follow appliance safety procedures when working near heating elements or live controls

The Grommet is an OEM part for Whirlpool gas cooktops. It forms a protective barrier and seal where wiring or mounting bolts pass through ventilation cutouts.

Causes of a bad grommet typically include degradation of the rubber material over time due to heat exposure during cooking. Physical stress from repeated installation/removal can also crack or loosen the seal.

Symptoms of a bad grommet include:

• Air leaks appearing around wiring/bolt openings  
• Drafts disturbing burner or element temperatures
• Noise from loose fixtures rattling 
• Risk of sparks near exposed connections

Replacing with an OEM grommet restores the protective seal while blending seamlessly with range aesthetics. Compatible brands include KitchenAid, Jenn-Air, and select Kenmore cooktop models. 

This surface burner knob replaces a worn or missing control knob on your gas cooktop or range, restoring precise flame adjustment and a clean, finished look. It fits onto the burner valve stem for smooth, reliable operation.

• Turns the surface burner valve to control flame level from low to high
• Common fix for knobs that are cracked, stripped, loose, hard to turn, or missing
• Helps when burner heat is difficult to set or won't hold steady
• Restores consistent, easy-to-grip control of the burner

• Turn off power and ensure all burners are cool before starting; shut off gas supply if working near the control area
• Pull the old knob straight off the valve stem—do not pry against the control panel
• Align the new knob with the stem orientation and press firmly until fully seated
• Test burner operation to confirm smooth adjustment through the full range

RF White

Control knob restores a worn or damaged range/stove control interface so you can select settings reliably. Installs quickly to replace missing, cracked, or loose knobs and improve control feel. What it does:

• Replaces a damaged or missing flush-style control knob so you can select heat/power settings accurately.
• Fits over the control shaft to provide a secure grip and tactile feedback when turning.
• Common symptoms: broken, loose, cracked, or missing knob; difficulty selecting or holding settings.
• Helps prevent accidental setting changes compared with a worn or slippery knob.

• One control knob

• Disconnect power to the appliance and turn off gas supply before beginning work.
• Remove the old knob by pulling it straight off the control shaft; align and push the new knob onto the splines until it seats.
• Do not force a knob that doesn't fit—verify shaft type and orientation before installing.
• After installation, restore power/gas and test all control positions for correct operation.