Need Help?
Call
Replace a worn, cracked, or broken microwave door hinge to restore smooth door movement and proper alignment. Ensures the door opens, closes, and seals.
Pressure regulator for gas ranges and cooktops. Mounts to the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.
Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.
Ordered the two hinges, removed the oven door and replaced the hinges. Read more
Secures the gas orifice beneath your cooktop and routes gas to the burner head. Replace if cracked, damaged, or missing to restore proper alignment.
Replaced damaged burners and all screws using anti-seize. Also I found that a couple of the gas lines had seized in the nuts, so I replaced the lines with 1/8" copper tube and new compression fittings. Read more
Burner won't heat or stays on high? This dual radiant surface element restores proper heating. DIY-friendly repair—lift cooktop, disconnect wires.
Googled "How to fix Whirlpool flat surface element"? Up came a YouTube video of how to remove screws and lift top to remove part and order a new one. It was important to know the Model number and as soon as I had that it took a few minutes to google a parts replacement site. This site was very quick and easy and I had the part in 2 days and installed in just a few minutes. Read more
Replace a cracked, stripped, or missing control knob on your electric range. This knob snaps onto the control shaft for accurate cycle and temperature selection.
Ordered a new knob and replaced it Read more
Controls gas flow and pressure to burners and oven in gas ranges. Replace if leaking, cracked, or damaged to restore safe gas distribution.
Replaced regulator with new one. Read more
Fixes igniters that won't stop sparking or burners that won't re-light when flame goes out. Controls ignition system for reliable burner lighting.
I replaced the burner switches, since we had been having trouble with specific burners igniting unless another burner was tuned on. Then I replaced the spark module since the flame and the burner being turned off were not being detected and burners would not re-light if the flame went out. Read more
This fixed thermostat switches near 60C to control a heat-managed circuit—often the oven's cooling/blower fan. Replacing a failed unit restores proper fan cycling and helps protect the control area from excessive heat during and after cooking.
Following the instructions that I received through the helpful research of the APP staff, I disconnected the power, disassembled the back of the oven, and accessed the hidden element. This involved bending parts of the sheet metal and cutting the insulation, so I was very apprehensive about doing this. Once I exposed the compartment that contains the element, I had difficulty extracting the old part and was really nervous about pulling hard to extract it - until I saw the damaged element. It... Read more
LF, LR, RR Stainless
Burner won't heat or heats unevenly? This surface heating element restores reliable heat to your electric cooktop. Moderate DIY repair in 30-60 minutes.
Replaced with new burner. Read more
Cast iron burner grate for gas ranges and cooktops. Sits atop burners to support pots and pans. Replace if warped, melted, cracked, or damaged.
Burner won't heat or heats inconsistently? This surface element restores cooking performance. Simple swap-out repair—unplug old, plug in new.
Replaced 6" burner. Read more
Fix a dual burner that won't heat or lacks proper temperature control. This infinite switch restores heat regulation for accurate simmer-to-boil cooking.
Ordered a new switch (4456027) from you. You seemed to have the best price and guaranteed that it was a OEM part -not everybody did. I had repaired Jenn Air cook tops before so I thought this was not a problem. Wrong. Mostly it was my own stupidity. I exchanged the wires from the old switch to the new one at a time but did write down where the original wires went. Flipped the breakers back on. Only one heater got hot. Searched the internet for several days for a wiring diagram. Nothing much.... Read more
Fix burners stuck on high or with no heat control. This infinite switch restores precise temperature adjustment. DIY-friendly repair in under an hour.
Watched appliance parts pros video on YouTube to determine which part to replace. Ordered parts and followed how to video and replaced parts. Read more
Sits atop the burner head to shape flame and shield from spills. Replace if missing, chipped, or warped to restore proper flame pattern and appearance.
Replaced the Gas Burner Head and Burner Cap.. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.