Kitchenaid Dryer Fuse Or Sensor

The Thermal Fuse is an OEM part for Whirlpool dryers. This safety device protects the dryer from overheating by cutting off power if the dryer exceeds a certain temperature. It is crucial for maintaining safe operation and preventing potential fire hazards. This thermal fuse has 1/4-inch terminals and operates around 243 degrees F. 

Causes of a bad thermal fuse include lint buildup causing overheating, blocked ventilation, or a malfunctioning thermostat. These issues can lead to the fuse blowing to prevent further damage or risk.

Symptoms of a bad thermal fuse include:

• Dryer not starting
• No heat in the dryer
• Dryer shutting off mid-cycle
• The dryer running but not heating

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The High Limit Thermostat is an OEM replacement part for Whirlpool dryers. Located on the heater housing, it functions as a critical safety component monitoring drum compartment temperatures. L295-50F.

Causes of thermostat failure include normal conductor fatigue from many heating cycles over extended usage. Chemical degradation potentially infiltrates components as well.

Symptoms of an ineffective high-limit thermostat include:

• Dryer fails to automatically disengage heat above certain temperatures
• Decreased safety risking overheating scenarios
• Dryer will not start
• Dryer shuts off prematurely

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Moisture Sensor is an OEM part for Whirlpool dryers. This part detects the moisture level in the clothing during the drying cycle, allowing the dryer to adjust the drying time accordingly. 

Causes of a bad moisture sensor can include regular wear and tear, buildup of lint or residue, or physical damage. 

Symptoms of a bad moisture sensor include:

• Clothes taking longer to dry or coming out still damp
• The dryer not stopping when clothes are dry
• The dryer shutting off prematurely
• Inconsistent drying results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This high-limit safety thermostat monitors temperature on the dryer's heater housing and opens the heating circuit if temperatures climb too high. It helps protect components from overheating and can restore safe, reliable heating when the original control has failed. What it does

• Monitors heater housing temperature and opens the circuit on overheat
• Acts as a safety backup for the heating system to prevent damage
• Failure symptoms can include: dryer runs but no heat, intermittent heat that stops mid-cycle, or the thermostat testing open at room temperature
• Repeat trips often indicate restricted airflow; check venting and lint buildup

• One high-limit thermostat

• Disconnect power; for gas models, also shut off the gas supply
• Note wire locations, remove the old thermostat from the heater housing, and transfer wires to the new part
• Mount the thermostat flush to the housing for proper sensing; secure with existing hardware
• Before reassembly, clear lint and ensure proper airflow through the lint screen, duct, and exterior vent

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

This ignition electrode delivers the spark needed to light the burner in compatible gas ovens and ranges, restoring reliable ignition so burners and bake/broil functions light properly. What it does:

• Produces the spark for the gas burner to ignite
• Helps ensure consistent ignition timing and burner starts
• Commonly used when a burner fails to light or ignition is intermittent
• Works with the oven/range ignition system to start bake and broil cycles

• Disconnect power and shut off the gas supply before starting any repair
• Handle the ceramic/insulated tip carefully to avoid cracking or contamination
• Verify correct electrode position and secure mounting for reliable sparking

L205-40. Dryer