Lawn Chief Parts

If your snow blower won't throw snow or runs roughly, the impeller shaft may be worn or damaged. This rotating component drives the impeller assembly.

Fix transmission engagement issues with this right actuating arm. Controls clutch and brake operation on lawn tractors. Direct-fit replacement part.

If your lawn tractor belt keeps slipping or won't engage properly, a worn pulley assembly is often the cause. This part connects components for operation.

Miter gear for garden tractor transmission systems. Replaces worn, stripped, or broken gears that cause grinding or mechanical failure in the drive assembly.

Fix tiller transmission issues with this 17-tooth spur gear. Restores power transfer when gears slip or grind. Fits most rear-tine tiller models.

This clutch collar is an authentic OEM part sourced directly from the manufacturer for use in lawnmowers and lawn tractors. If there are problems with the lawnmower jerking and sputtering after changing gears, the clutch collar should be removed and replaced to keep the lawnmower running properly. The clutch collar is part of the clutch bearing. The clutch collar is used between bevel gears as spacers and allows them to move in sync with the pinion gear. If the clutch collar is deteriorated, broken, or missing, a new one should be installed.Make sure the lawnmower is on a flat surface. Remove the spark plug and disconnect the battery. A screwdriver, pliers, socket set, wrench set, and nut driver are required to make this repair. Take the transmission out of the lawnmower. Open the case on the transmission and remove the broken clutch collar. Install the new clutch collar. Reverse the process to reassemble the lawnmower. This clutch collar is a high tensile metal part that is sold individually. It is designed for use in lawn tractors manufactured by Craftsman.

This is an upper housing that is used with many models of lawnmowers and lawn tractors. The part is made of durable metal and has the responsibility of protecting many of the interior parts of the lawnmower. Over time, the upper housing can be damaged or may break. It can also be lost and will need to be replaced with a new OEM component. If the housing is damaged or cannot be found, the part should be replaced.Basic tools like a screwdriver and socket may be needed for this project process. A pair of work gloves will also be useful for the process. Before replacing the upper housing, make sure the lawnmower is placed on a sturdy surface and in the off position. The spark plug wire should be disconnected for safety reasons. Use the tools to remove the old damaged part from the lawnmower before installing the new one in its place.This upper housing is designed to compatible with lawnmowers and lawn tractors manufactured by Montgomery Wards, MTD, Ryobi, and Yard Machines. It is an authentic OEM replacement part that is directly sourced from the manufacturer. This component is sold individually.

Replacement foam handle grip for lawn mowers and tillers. Cushions metal handles for comfortable operation. Replace if worn, torn, cracked, or missing.

Seals the gear case to prevent oil leaks in your tiller. Replace when worn, cracked, or leaking. Verify fit with your model number before ordering.

This is an oil filter designed for use in larger gasoline-powered landscaping and outdoor equipment such as log splitters and chippers. An oil filter is an essential safeguard to maintain a good operating condition and ensure long life in a gas engine. Oil filters remove toxic chemicals as small pieces of debris that can end up in the engines. Because these contaminants, if improperly removed, could also end up in the air or in the environment in other ways, oil filters must be meet EPA emission regulations. This filter not only meets federal environmental standards but also is an OEM guaranteed replacement part that is manufactured to the identical specification of the original parts being replaced. By the very nature of what it's supposed to accomplish, eventually, the filter will need to be replaced. Over time the filter's elements will become full of debris, and failing to replace it in a timely manner runs the risk of allowing the captured pollutants to escape back into the engine oil. When replacing the old filter, make sure to follow environmental guidelines as well, disposing of the oil and filter according to posted regulations. Replacing the filter is the ideal time to replace the engine oil as well. This filter is compatible with Husky, Cub Cadet, Troy-Bilt, Yard-Man, and MTD equipment.

This actuator spring is a genuine MTD part, sold individually. This actuator spring can be used as a replacement part in a lawn mower. The purpose of the actuator spring, also known as a seat spring switch, in a lawn mower is to provide a plate upon which the seat switch can conduct its electrical current while being held stably in place.If the actuator spring slides out of place and cannot be reinstalled or if it is bent, broken, dented, or worn beyond repair, it should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This actuator spring is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard Man, Turf King, and MasterCut.

Hydraulic tube for log splitters. Connects hydraulic components and reduces vibration. Replace if cracked, leaking, or damaged during operation.

Replacement plastic rivet for lawn mowers and tractors. Secures panels, covers, and trim pieces. Order a new rivet if yours is broken or missing.

Replace your snow blower's belt cover to protect the drive belt from snow and debris. Essential when cracked or missing to prevent belt damage. Verify fit with your model number before ordering.

This tamper plug is a genuine MTD part. It is manufactured as a replacement part for several models of chippers, wood chippers, shredders, and vacs.On a wood chipper, the tamper plug is an optional part that can be used to manually push material into the shredder toward the blades. It is designed to help the chipper function properly while protecting users' hands. The tamper plug can become damaged if it comes into direct contact with the blades, and also may wear out over time.This tamper plug is a genuine OEM part sourced directly from the manufacturer. It is compatible with several makes of wood chippers and shredders, including Craftsman, Huskee, Husky, Lawn Chiefs, MTD, White Outdoor, and Yard Machines.