Lawn Chief Parts

Replacement extension spring for lawn tractors and mowers. Installs internally to create tension for proper operation. Needed when original is broken, stretched, or missing.

Replacement wheel assembly with tire for chipper shredders and lawn equipment. Restores mobility when original wheel is cracked, worn, or broken.

Small metal washer that installs with screws and bolts throughout lawn mowers and outdoor power equipment. Replace if cracked, worn, or missing.

Flat washer for lawn tractors and mowers. Replace when worn, damaged, or lost to ensure proper hardware fit and secure assembly. Verify compatibility.

Small metal washer for lawn mowers and outdoor power equipment. Replaces cracked, worn, or missing washers. Ensures proper spacing and assembly.

Replacement wheel axle for snow blowers. Attaches wheels to the frame assembly. Replace if bent, broken, or worn from use. Direct OEM part.

This is a thrust bearing. The thrust bearing is positioned between the lawn mower's spindle and front axle and serves to reduce friction during use. This part makes shifting between different speeds much easier. A worn-out thrust bearing will have more room between the rollers on the outside of the bearing. This movement will cause the bearing to move more than usual. When the bearing goes bad, the driver may notice rattling, squeaking, or other noises coming from the machine. These noises can be more prevalent when the clutch pedal is engaged. To replace the thrust bearing, first, the clutch must be removed from the lawn mower. On the bottom of the driveshaft, there is a bolt and washer that need to be removed. Wedge and move the clutch, allowing it to work its way down the driveshaft, then remove it. There is a bearing retainer clip and three bolts that will enable the thrust bearing to be removed. Repeat the steps in reverse after installing the new component.This product is a genuine OEM MTD part sourced directly from the manufacturer. The part is sold individually and not available with any other components. This product is compatible with MTD and Cub Cadet products.

Height adjustment bearing for lawn mowers. Replace if wheels don't adjust smoothly or height settings slip. Verify fit with your model number.

This is a metal connecting rod that attaches the rear debris guard to the tiller frame, keeping the guard properly positioned during operation. It ensures the guard stays in place to deflect dirt and debris kicked up by the tines. Replace this rod if it is bent, broken, or missing, which can cause the rear guard to hang loosely or fall off during use.

Replace a worn or bent cam rod that causes poor shifting or control issues in your snow blower. Direct fit part restores smooth operation.

Tie rod for lawn tractors. Connects steering components for proper wheel alignment. Replace if bent, damaged, or worn to restore steering linkage function.

Replacement steering drag link for lawn tractors. Connects steering components for proper wheel control. Replace if bent, cracked, or worn for safe operation.

Bearing spacer aligns wheel bearings on the axle between the two bearings. Replace if worn or damaged to ensure proper wheel operation. Verify fit.

Replacement spacer for lawn mowers and tractors. Maintains proper spacing between components. Order a new spacer if yours is missing, damaged, or worn.

Gas gauge not showing fuel level or stuck on your riding mower? This replacement gauge restores accurate fuel monitoring. Simple installation.

This is a cylinder seal kit that is made for log splitters. Each of the seals is a part that helps the cylinder work so the log splitter can do its job. The cylinder seals are made of durable rubber and prevent air from leaking inside of the log splitter. With ordinary use, the cylinder seals can start to stretch or become brittle and may be incapable of keeping out air. When this occurs, the seals will need to be replaced with the ones in a cylinder seal kit.When replacing cylinder seals, a basic tool kit and a pair of work gloves may be needed. The log splitter should be turned off and have the spark plug wire disconnected. Place the splitter on a stable surface and disassembly it to gain access to the inner components. The old cylinders can be removed before replacing them with the contents of the cylinder seal kit.This cylinder seal kit is designed to be compatible with a variety of log splitters created by Cub Cadet, MTD, and Yard Machines. The component is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.