Lg Dryer Duct Parts

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.

The Lint Filter Guide is an OEM part for LG dryers. It holds the removable lint filter screen securely in place. Proper alignment and secure mounting of the lint filter is important for effective filtration.

Causes of a faulty lint filter guide can include wear and tear from years of inserting and removing lint screens. Damage such as cracks or breaks could compromise secure mounting.

Symptoms of a problematic filter guide include:

• The lint screen not sitting correctly or falling out of alignment
• Inability to fully insert or remove the lint screen
• Lint scattering inside washer rather than collecting in screen

This OEM LG part is also compatible with some Kenmore models.

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

This parts assembly is the factory replacement service assembly that houses and connects the appliance's internal components, restoring proper electrical and mechanical function when a worn or damaged assembly causes failures. What it does

• Replaces a damaged or worn internal assembly that can cause control failures or intermittent operation
• Restores secure electrical and mechanical connections between internal components
• Helps resolve symptoms like no power to controls, erratic operation, or components not responding
• Matches OEM fit and form to maintain original performance

• Intended for technicians or experienced DIYers; disconnect power before starting any repair
• Handle with care to avoid damaging connectors, wiring, or delicate components
• Reuse existing mounting hardware unless replacements are specified
• Test appliance function after installation and secure all panels before restoring normal use

This duct assembly channels exhaust from the appliance to the home vent, restoring proper airflow and helping reduce lint and moisture buildup. It's a direct-fit replacement for the original ducting on compatible LG units. What it does:

• Directs heated air and moisture from the appliance to the exterior vent
• Replaces damaged, crushed or disconnected ductwork that can restrict airflow
• Helps reduce lint accumulation in the cabinet/vent path when installed and maintained
• Restores a sealed connection between the appliance outlet and household venting

• Disconnect power and unplug the appliance before beginning any repair
• Follow for disassembly and routing; use proper clamps or screws to secure connections
• Inspect connected gaskets, clamps and the external vent path; replace or clean as needed
• Do not operate the appliance with obstructed or damaged venting; clean lint regularly to reduce fire risk

This duct assembly channels airflow inside the appliance to guide exhaust and internal air between components. Replacing a damaged or obstructed duct helps restore proper airflow and can reduce poor performance or long cycles. What it does:

• Directs exhaust and circulation air between internal components to maintain airflow
• Prevents leaks that can reduce efficiency or cause longer cycle times
• Helps avoid overheating or moisture build-up from restricted airflow
• Reduces rattling or vibration caused by a cracked or loose duct

• Disconnect power (and turn off gas supply for gas appliances) before beginning work.
• Handle edges carefully — sheet metal can be sharp; wear cut-resistant gloves.
• Ensure duct is seated and fastened to create a tight seal where it connects to other components.
• After reassembly, run a test cycle to confirm airflow and proper operation.