Lg Range / Cooktop / Oven Heating Element

The Bake Element is an OEM part for LG ranges. This part provides the necessary heat for baking by distributing heat evenly from the bottom of the oven cavity. 

Causes of a bad bake element can include normal wear and tear over time, exposure to high heat leading to deterioration, or electrical issues causing the element to short out.

Symptoms of a bad bake element include:

• Oven not heating evenly or not reaching the set temperature
• Visible damage such as breaks or blisters on the element
• The element not glowing red when in use
• Longer cooking times than usual

This OEM LG part is also compatible with some Kenmore models.

Restore consistent heat to your smooth-top range. This radiant surface element sits beneath the glass-ceramic cooktop and provides the controlled heat needed for boiling, simmering, and sautéing when the surface control sends power. What it does:

• Generates radiant heat beneath the glass cooking surface when energized
• Works with the surface control to reach and maintain the set temperature
• Helps address a burner that won't heat or only heats intermittently
• Replaces a failed or visibly damaged element to restore proper cooking performance

• One radiant surface heating element

• Disconnect power by unplugging the appliance or switching off the circuit breaker before servicing
• Lift and support the glass cooktop per your model's service procedure to access the elements
• Note wire locations; transfer any brackets or clips from the old element to the new one
• Handle carefully and avoid flexing the heating coil; ensure the element sits level before reassembly

This radiant surface element mounts beneath the glass cooktop to heat a surface burner. Replace it when a burner won't heat or heats intermittently to restore normal, consistent cooking performance.

• Generates radiant heat under the glass-ceramic top for a surface burner
• Cycles on and off to help maintain the set temperature
• Typical failure signs: no heat, intermittent heat, or visible damage to the element/terminals
• Used on electric ranges and glass cooktops

• Disconnect power at the breaker and allow the cooktop to cool fully before service
• Lift/hinge the glass top and support it to avoid stress or cracks
• Note wire positions; transfer any mounting clips/brackets from the old element to the new
• Ensure the element sits level under the glass and all connections are secure before reassembly

This sheath-style heater delivers controlled heat during your appliance's defrost or heating cycle. Replacing a failed element restores proper temperature performance, avoiding issues like weak/no heat, extended run times, or frost accumulation where defrost heat is applied.

• Provides focused heat for defrost or heating functions as engineered by the manufacturer
• Typical failure symptoms: no or weak heat, uneven temperatures, frost/ice buildup in areas that should defrost, longer run times, or related error codes
• Helps maintain stable performance and efficiency by delivering the required heat at the right time

• Disconnect power and allow hot components to cool before servicing
• Access the heater per your model's service manual; take photos of routing and clips before removal
• Avoid bending adjacent tubing, coils, or brackets; transfer any clips or shields from the original part
• Ensure all electrical connectors are fully seated; restore power and monitor operation

This part is the radiant heater intended for use on ranges. This part is also referred to as a surface element. It supplies the heat required to cook food. This particular radiant heater is the largest element on the cooktop. In the event that the burner is not heating up, this part may need to be replaced as there could be an element that is burned out. It may begin to heat up but won't get hot enough to cook correctly. The cook may also notice that the element does not cook evenly. There could also be physical signs of damage. Be sure to unplug the range prior to attempting to repair or replace this part.This particular radiant heater is compatible with appliances manufactured by the LG brand. It is sold individually. This part comes straight from the manufacturer.

This radiant surface element mounts beneath the glass cooktop to heat a burner zone on your range. Replacing a failed element restores consistent, responsive heating and reliable temperature control for everyday cooking.

• Provides controlled electric heat under the glass for the selected cooking zone
• Works with the range controls to cycle on/off and maintain the set temperature
• Common symptoms: burner won't heat, heats intermittently or only in spots, or the indicator comes on but the surface stays cold
• Visual clues can include a broken or blistered heating coil visible beneath the glass

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/prop the glass top per service procedure; note wiring and bracket locations before removal
• Transfer any brackets/insulators from the old element and make secure, like-for-like connections
• Handle the glass and element carefully; test operation before final reassembly

The Heating Element is an OEM part for LG ranges. It is responsible for providing heat to the oven cavity, allowing for proper cooking and baking. 

The heating element is exposed to high temperatures with each use and over time can become brittle or defective. Causes of a bad heating element can include cracks in the coils, burn marks, or faulty electrical connections. 

Symptoms of a bad heating element include: 

• The oven not heating up or heating unevenly
• Diminished cooking power 
• Burning or burning smell from the oven
• Tripped circuit breaker or blown fuse

Replace yours today with this genuine LG heating element and restore your oven's full cooking capabilities. This OEM LG part is also compatible with Sears/Kenmore.

This heater assembly replaces the dryer's heating unit to restore normal drying performance and consistent drum temperatures. It's a direct-fit replacement designed to match the OEM heater layout and electrical connections. What it does:

• Reheats incoming air so the dryer can remove moisture from clothes.
• Works with the dryer's blower and thermostat to maintain operating temperature.
• Commonly used when the dryer produces little or no heat, or runs long cycles.
• Helps resolve intermittent heating caused by a failed heating element or broken heater housing.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access requires removing the dryer cabinet or rear panel; follow OEM disassembly steps.
• Inspect related parts (thermal fuse, high-limit thermostat, wiring, connectors) for damage while replacing the heater.

The Broil Element is an OEM replacement part for LG electric ranges. As a vital upper heating system, this broil element helps efficiently brown and crisp foods placed directly under or on the top rack of the oven.

Causes of a defective broil element may relate to normal wear and tear on the coils from repeated high-heat cooking. Food residues adhering over time can reduce performance.

Symptoms of a problematic broil element include:

• Inadequate or uneven browning from the top-level heating system   
• Diminished functionality of the broil setting on the control panel
• Potential thermal damage or exposed wiring from a failed element

This OEM component fits some Kenmore/Sears electric range models as well. 

This radiant heater is the electric heating element assembly that warms air inside the dryer so clothing dries efficiently. It replaces a failed heater assembly to restore normal drying heat and cycle performance. What it does:

• Generates the heat needed for an electric dryer to dry clothes
• Replaces a damaged or burned-out heating element assembly
• Commonly used when the dryer produces little or no heat or takes too long to dry
• Works with the dryer's thermal controls and airflow system to maintain operating temperature

• Disconnect the appliance from power before servicing to avoid electric shock
• Inspect and replace any damaged wiring or thermal fuses while access is available
• Handle the element carefully to avoid bending or breaking; follow OEM installation instructions
• After installation, test the dryer on a short cycle and verify proper heating and airflow

This radiant surface element sits beneath the glass cooktop and provides heat to a single burner on an electric range. Replacing a failed element restores fast, even heating and reliable temperature control on that cooking zone. What it does:

• Generates radiant heat under the glass for one surface burner
• Works with the control to cycle and maintain the selected temperature
• Common symptoms: burner won't heat, heats slowly or unevenly, or only part of the ring glows
• Visible breaks or damage to the element under the glass

• 1 radiant surface element

• Disconnect power at the breaker before servicing
• Allow the cooktop to cool completely and protect the glass surface
• Lift/remove the glass top to access the element; transfer any brackets/retainers from the old unit if required
• Move wires one at a time to matching terminals and center the element under the burner graphic before reassembly

This is a radiant surface element for a stove cooktop. This part uses a resistance wire to create heat for cooking meals. It has an exposed wire along the surface where the heat comes from.If the radiant surface element is damaged, it may not heat correctly. Replacing it requires a Phillips screwdriver, pliers, and work gloves. Turn off the power to the range and open up the oven door to pull the cooktop assembly forward. Prop it open for access to the internal components. Remove the screws on the support bracket and remove the radiant surface element. Next, transfer the new component into the stovetop and connect it to all other components. Add power back to the appliance when done.The radiant surface element is sold as a single part. It's a genuine OEM product that is made for ranges manufactured by LG. This part is directly obtained from the manufacturer.

This radiant heater is the oven/stove heating element that provides consistent radiant heat for baking and broiling. Replaces a failed element to restore proper cooking temperatures and even heat across the oven cavity. What it does:

• Converts electrical power into radiant heat used for baking and broiling
• Heats up evenly to maintain oven temperature during cooking cycles
• Commonly replaced when oven fails to heat or heats unevenly
• A solution for visible element damage, open/short electrical readings, or blown fuses/tripped breakers related to the oven circuit

• Disconnect power to the appliance before servicing to avoid electrical shock
• Inspect connectors and mounting hardware; replace any damaged fasteners or wiring
• Handle the element carefully to avoid bending or damaging terminals