Parts for Speed Queen ADEE9BGS173TW01: Loading Door-Without Window Parts

This door strike bracket mounts to the cabinet and positions the door strike so the door latches securely and the machine recognizes a closed door. Replace a bent or broken bracket to restore proper door alignment and reliable starts.

• Supports and aligns the door strike with the latch/lock assembly
• Ensures the door switch/interlock is engaged when the door is shut
• Helps prevent nuisance "door open" messages and cycles that won't start
• Direct replacement for a damaged, bent, or missing bracket

• Disconnect power before servicing; shut off water or gas supplies if applicable
• Open the door and access the bracket from the front panel area
• Note bracket orientation; transfer and install using existing hardware; align before tightening
• After reassembly, the door closes firmly and the machine starts without a door error

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

This door liner seal provides a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. Designed as a direct-replacement service part for compatible Speed Queen front-load washers. What it does:

• Seals the gap between the door and the tub to stop water from escaping during wash and rinse cycles
• Helps maintain proper drum containment and reduces water on the door opening
• Commonly replaced when you see visible wear, tearing, or persistent leaking from the door area
• Compatible with OEM door assembly designs that use a packaged liner seal

• Follow manufacturer instructions for proper seating and clamping
• Inspect surrounding door boot and latch for damage; replace if worn to ensure a proper seal
• Disconnect power and water supply before starting work to reduce risk of shock or flooding
• Test with a short cycle and check for leaks after installation

This is a 8-16 x 5/8 tapping screw with a #6 Phillips drive, used to fasten panels and components on compatible appliances. It provides a secure, low-profile hold for trim, brackets and covers. What it does:

• Secures panels, trim pieces, brackets or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment and fit of exterior or interior panels
• Provides a threaded connection in sheet metal or tapped holes

• Use the correct #6 Phillips screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure alignment, then tighten until snug — do not overtighten
• Replace stripped or damaged screws to ensure secure fastening
• Wear eye protection and disconnect power to the appliance before working on components

This door hinge secures and lets the appliance door pivot smoothly, restoring proper alignment and reliable opening/closing. A direct-fit replacement designed to return worn or damaged hinges to correct function. What it does:

• Supports the door and provides a pivot point for opening and closing
• Restores proper door alignment and prevents sagging or uneven gaps
• Helps the door latch and seal correctly by maintaining hinge position
• Common symptom fix: loose, noisy, tilted, or non-closing door

• Disconnect power and water before beginning any repairs
• Support the door during removal/installation to prevent dropping or damage
• Use the factory mounting screws and torque to OEM spec; replace damaged fasteners
• If alignment or latch issues persist after install, check strike and door seal for wear or damage

A replacement wedge for the door handle that restores a secure grip and smooth door operation. Fits the white trim area of the handle assembly to replace cracked, broken, or worn wedges and improve door feel. What it does:

• Replaces a damaged or missing wedge piece that holds the door handle trim in position.
• Restores a stable gripping surface so the door opens and closes without slipping.
• Helps correct symptoms such as a loose, cracked, or partially detached handle wedge.
• Matches the white finish used on the handle trim for a consistent appearance.

• One white wedge door-handle piece as shown

• Disconnect power to the appliance before starting any repair.
• Installation typically requires basic hand tools; remove the handle/trim to access the wedge.
• Align the wedge and snap or fasten into place without forcing; avoid over-tightening fasteners.