Parts for Roper 2872W0A: 03 - Lower Body Parts

Flat-head 10-32 zinc screw secures panels and components on cooktops, ranges, and ovens. Replace stripped, missing, or corroded screws for proper fit.

This genuine replacement push button restores a worn or damaged control panel button so your appliance's controls respond correctly. Designed for direct fit and everyday use on compatible Bosch control assemblies. What it does:

• Replaces a cracked, chipped, or missing control panel push button
• Provides a responsive surface that engages the underlying switch when pressed
• Helps resolve symptoms like a button that sticks, fails to register presses, or looks visibly damaged
• Matches OEM form for correct alignment and tactile feedback

• Disconnect power (unplug or shut off breaker) before beginning any repair.
• Access typically requires removing the control panel overlay or trim; keep screws and fasteners organized.
• Handle the button and surrounding trim carefully to avoid scratching the finish.

This oven grommet is a small rubber or plastic insulating component that cushions wires or protects openings. Replace when cracked, worn, or missing.

A replacement hex nut used to secure appliance components and restore proper fastening. Installs quickly and helps stop loose or rattling parts caused by a missing or stripped nut. What it does

• Secures mounting studs, brackets, or components in place
• Prevents parts from shifting, vibrating, or coming loose during operation
• Replaces a missing, damaged, or corroded nut to restore reliable fastening

• One hex nut

• Disconnect power and gas before starting work
• Start threads by hand to avoid cross-threading, then tighten with the proper-size wrench
• Do not overtighten; snug until secure to avoid damaging studs or threads
• Use replacement only where the OEM hex nut is specified

Replacement screw for securing components inside your range or oven. Needed when original fasteners are stripped, lost, or damaged during repairs.

This part has been discontinued by the manufacturer and is no longer available.

High limit thermostat, Canadian models only.

A small trim screw designed to secure appliance trim pieces and molding, restoring a finished look and keeping panels held firmly in place. Ideal when a trim piece is loose, missing a fastener, or shows minor rattling. What it does:

• Fastens trim, molding, or decorative panels to the appliance frame
• Restores secure mounting and helps eliminate loose or rattling trim
• Replaces missing or stripped fasteners that cause gaps or poor fit
• Compatible with common trim attachment points where OEM screw is specified

• Disconnect power or unplug the appliance before attempting repairs
• Use the correct screwdriver bit to match the screw head to avoid stripping
• Install by hand to start threads, then tighten snugly—do not overtighten
• Verify trim alignment after installation and test that the panel is secure

Package of 12

Made by Whirlpool. 240Volt. Size: Width 19-7/8"; Length 15-1/4"; Mount bracket to terminals 3-5/8"; Space between terminals 1-3/4".

Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.

This part has been discontinued by the manufacturer and is no longer available.

The Support Bracket is an OEM part for GE ovens, designed to provide stability and support for the broiling element. This bracket is essential for ensuring the broiling element is securely positioned at the top of the oven, allowing for even heat distribution and optimal cooking performance when broiling foods.

Causes of damage to the support bracket often involve high heat exposure, accidental impacts during cleaning or cooking, or general wear and tear over time. 

Symptoms of a bad Support Bracket include:

• The broiling element hanging lower than usual or touching the oven cavity, which can affect cooking performance and potentially damage the oven's interior.
• Unstable or loose broiling element, leading to uneven cooking or broiling.
• Visible signs of wear, damage, or corrosion on the bracket itself, indicating it may no longer provide adequate support.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.