Parts for Ge CGS990SET9SS: Lower Door Parts

Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Replace your range's oven door liner weld assembly if the inner door panel is cracked, damaged, or separating. Restores door structure and appearance.

Replace your cracked, broken, or discolored range oven door window glass. This inner glass panel restores visibility and appearance to your oven door.

Rubber grommet that cushions and secures your range door handle. Replaces worn, cracked, or missing grommets to restore snug fit and quiet operation.

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

Insulation panel for range oven doors. Installs between door panels to provide heat retention. Replace if cracked, compressed, or missing for proper fit.

Insulation guard for electric and gas ranges. Protects internal insulation from heat damage. Replace if cracked, deteriorated, or missing.

10-32 x 9/16 hex washer head screw secures control panels, brackets, and trim to your electric range frame. Replaces worn, missing, or stripped fasteners.

Replace your range oven door handle tube if the original is cracked, dented, or missing. This stainless steel tube installs on the door for secure grip.

Mounting screw for range installation and component assembly. Replace if stripped, rusted, missing, or damaged to ensure secure attachment of parts.

Fiberglass gasket cord for range door or panel sealing. Replaces worn, frayed, or missing cord that no longer seals properly. Ensures tight fit.

A replacement inner door insulation that restores the refrigerator door's thermal barrier to help maintain proper temperature and reduce condensation. Fits behind the door panel to support efficient cooling and prevent cold air loss. What it does:

• Replaces damaged or compressed insulation that can allow cold air to escape
• Helps reduce moisture buildup and frost on the door interior
• Supports consistent internal temperatures for better food preservation
• Dampens noise and helps the door close more evenly

• Disconnect power to the appliance before starting any repairs
• Remove the door panel and any trim or handles to access the insulation
• Handle carefully around sharp sheet metal and retain any fasteners for reassembly
• Use the exact replacement part number for proper fit; avoid forcing or trimming the insulation

This oven door inner insulation cushions the inner door panel and helps maintain proper cooking temperatures while reducing heat transfer to the outer door. Replaces damaged or missing insulation to improve heating consistency and help keep the exterior cooler. What it does

• Fills the cavity behind the oven door's inner panel to limit heat loss and stabilize internal temperatures.
• Helps reduce outer door surface temperature for safer handling during and after use.
• Reduces drafts and uneven cooking caused by compromised or missing insulation.
• Works with the door inner panel and outer door assembly to restore proper sealing and performance.

• One door insulation

• Remove power to the appliance and allow the oven to fully cool before beginning work.
• Handle carefully to avoid tearing the insulation; use caution around sharp sheet metal and door glass.
• Follow manufacturer service manual or OEM instructions for door disassembly and reassembly.

Replace your cracked or missing oven door handle endcap with this durable trim piece. Secures to the end of the bar handle for a finished look.