Parts for Ge JGBS86SP2SS: Lower Door Parts

The Door Hinge is an OEM part for GE gas ranges. It acts as the pivot point that allows the oven door to smoothly and securely open and close. 

Symptoms of a bad hinge can include wear and tear over time, damage or bending due to excessive force applied while opening or closing the door, or failure of components that assist the door movement.  

Symptoms of a bad door hinge include:

• The door becoming misaligned and no longer closing or sealing properly 
• Difficulty or resistance when opening and closing the door
• Noise or squeaking coming from the hinge area
• Visual signs of damage or bending to the hinge itself

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This right-side door hinge secures and supports the appliance door, providing stable pivoting and proper alignment so the door opens and closes smoothly. It replaces a worn or damaged hinge to restore correct door fit and operation. What it does:

• Supports the weight of the right-hand door and provides the pivot point for opening and closing
• Restores proper door alignment when the door sags, binds, or sits crooked
• Helps stop scraping, rubbing, or uneven gaps that can affect sealing
• Works with existing hinge pins and mounting points to reestablish smooth movement

• One right-side door hinge

• Unplug the appliance or shut off power before starting any work; for refrigerators, also remove food and secure shelves/door
• Support the door while removing fasteners to prevent dropping or damage
• Keep all original screws and hardware; replace only what is specified for your model

This contoured washer is a shaped fastening washer used on compatible GE top-load washers to secure and cushion mating parts. It helps maintain proper alignment and reduces wear where parts bear against each other. What it does

• Provides a contoured bearing surface to help distribute load and reduce point wear
• Cushions and isolates components to help limit vibration and noise
• Secures fasteners or assemblies in tight, shaped recesses
• Helps maintain correct part alignment for reliable operation

• One contoured washer

• Disconnect power to the washer before servicing to avoid shock or injury
• Use proper tools and observe orientation; tighten fasteners to manufacturer guidance

The GE Glass Panel Door Assembly is an OEM part for GE ranges. It forms the main barrier sealing in heat during the cooking process. 

Causes of a bad door assembly can include cracks, chips, or breaks in the glass, damage to handles or hinges over time, or issues with the door seal not forming properly.

Symptoms of a bad door assembly include:

• Improper sealing when closed, allowing heat to escape 
• Difficulty smoothly opening and closing the door  
• Appearance issues such as cracks, fogging or film on the glass
• Warping of the internal panel affecting the door closure

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Stainless Steel Handle is an OEM replacement part for GE electric range models. It provides a sturdy grip for opening and closing the oven door.

Causes of failure include loosened mounting screws from repetitive use, bent or damaged profile from impact, and corrosion affecting appearance.  

Symptoms of a faulty handle include:

• Difficulty smoothly opening and closing the oven door 
• Risk of pinched fingers if handle wobbles during operation
• Degraded aesthetic and value of the appliance over time

This OEM stainless handle also fits select Hotpoint and RCA electric ranges.

This is a replacement screw used to secure panels and components on compatible appliances, providing reliable fastening to stop loose parts and noise. It restores proper fit where the original fastener is missing or damaged. What it does:

• Fastens control panels, brackets, or trim to appliance chassis
• Keeps components aligned to prevent rattling or vibration
• Replaces stripped or corroded mounting screws
• Restores secure connections that can cause gaps or poor fit

• Disconnect power before servicing the appliance
• Use the correct-size driver or socket to avoid stripping the head
• Thread in carefully and avoid over-tightening to prevent damage
• Check that the screw seats flush and secures the component fully

A replacement inner door insulation that restores the refrigerator door's thermal barrier to help maintain proper temperature and reduce condensation. Fits behind the door panel to support efficient cooling and prevent cold air loss. What it does:

• Replaces damaged or compressed insulation that can allow cold air to escape
• Helps reduce moisture buildup and frost on the door interior
• Supports consistent internal temperatures for better food preservation
• Dampens noise and helps the door close more evenly

• Disconnect power to the appliance before starting any repairs
• Remove the door panel and any trim or handles to access the insulation
• Handle carefully around sharp sheet metal and retain any fasteners for reassembly
• Use the exact replacement part number for proper fit; avoid forcing or trimming the insulation

This silicon controlled rectifier (SCR) is an electronic switching component used on appliance control boards to regulate power to heating elements or motors, restoring proper control and operation when the SCR fails. What it does:

• Acts as a power-control switch on control boards to deliver variable current to heaters or motors
• Helps regulate on/off cycles and output under control-board commands
• Failure may cause no heat, intermittent heating, or components not running as expected
• Replacing a faulty SCR can restore consistent power control and appliance function

• Disconnect all power before servicing; risk of electric shock or damage
• Static-sensitive component—use proper ESD precautions when handling
• Replacement typically requires desoldering/soldering on the control board or replacement of the control module

The Badge Assembly is an OEM part for GE ranges. It includes the magnetic decorative badge affixed to the front of the range. This badge displays important information such as the brand name, model number, and technical specifications.

Causes of a bad badge assembly can include damage from impacts or abrasions over time, adhesive failure from repeated heat exposure, or normal wear from routine cleaning. On a range, the badge must withstand higher cooking temperatures.

Symptoms of a bad badge assembly include:

• Faded or illegible print on the badge face
• Cracks or breaks in the plastic material
• The badge lifting or peeling away from the surface
• Missing or loose attachment clips/fasteners

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.