Parts for Ge JGB860BEJ2TS: Lower Oven Parts

Base spacer for gas ranges. Installs at the bottom of the range to provide proper spacing and support. Replace if cracked, broken, or missing.

A small mounting spacer that positions and supports internal components for proper alignment and clearance. Replaces a worn or damaged spacer to help maintain stable assembly fit and reduce interference between parts. What it does:

• Provides spacing between appliances' internal assemblies to ensure correct alignment
• Helps prevent metal-to-metal contact that can cause noise, wear, or improper sealing
• Restores correct fit when an original spacer is cracked, missing, or deformed
• Commonly used during repair of panels, assemblies, or mounting brackets

• Disconnect power (and gas if applicable) before starting any repair
• Handle surrounding panels and components carefully to avoid damage
• Installation may require removal of adjacent trim or brackets and a few fasteners

Fix an oven that won't hold temperature or runs too hot or cold. This temperature sensor monitors and regulates oven cavity heat for accurate baking.

This barrier bottom floor is the inner bottom panel that helps form the refrigerator's lower compartment, keeping components supported and directing moisture away from sensitive areas. Replaces a damaged, cracked, or missing bottom barrier to restore proper fit and protection. What it does:

• Replaces a cracked, broken, or warped bottom floor panel that can let debris or moisture reach components
• Restores the intended lower-compartment barrier that helps direct condensation and defrost water
• Provides a stable mounting surface for lower shelving/crisper assemblies and nearby components
• Helps reduce the chance of visible gaps or misalignment in the refrigerator base

• Disconnect power and empty the lower compartment before beginning work
• May require removal of lower drawers, trim pieces, or screws/clips for access
• Use basic hand tools; keep track of fasteners and any seals or gaskets removed

Replacement front frame bumper that cushions and supports your range's door trim. Prevents metal-on-metal contact and reduces vibration. Needed when original is cracked, broken, or missing.

This cover cap is a direct-replacement trim piece that covers an exposed control shaft or fastener, restoring a clean finished appearance and helping keep dirt and debris out of the opening. Ideal for cosmetic repairs and simple maintenance. What it does:

• Covers and protects an exposed shaft, screw head, or fastener from dirt and damage
• Restores the original finished look of the control area or panel
• Helps reduce snagging on clothing or objects around the shaft
• Prevents debris buildup that can affect surrounding components

• Always unplug the appliance or disconnect power (and water if applicable) before servicing.
• Many installs are push-fit—remove the knob or trim, press the cap into place, and reassemble.
• Keep parts organized for reassembly.

Replace your worn, bent, or warped oven rack. Provides a stable surface for baking sheets and pans inside your range oven. Fits standard ovens.

Bottom oven panel for gas ranges. Replaces cracked, damaged, or missing panels on the lower oven exterior. Restores the finished appearance of your range.

Replace your range oven door gasket to restore proper sealing and heat retention. Install when you notice heat escaping or uneven cooking. Verify fit.

Redirects heat away from the rear panel and components in your gas range oven. Replace if warped, damaged, or missing to protect surfaces.

Oven won't broil or brown food evenly? This upper heating element restores proper broiling function. DIY-friendly repair takes about 30 minutes.

Metal deflector shield that directs heat inside the oven cavity. Replace if cracked, bent, or missing to restore proper airflow and heat distribution.

Fixes range oven that won't heat when door is closed. This door plunger switch activates burners and baking modes. Common DIY repair in 30 minutes.

Positions and supports internal components to maintain proper alignment and clearance. Replace if cracked, broken, or missing to restore stability.

Right-side lower support base that secures and stabilizes the range cabinet. Replace if cracked, broken, or worn to restore proper alignment and fit.

Replaces the left lower support base that stabilizes your range's lower assembly. Needed when the original is cracked, broken, or missing.

Replacement leveling leg for ranges. Installs at base corners to stabilize and level your range on uneven floors. Needed when leg is broken or missing.

Metal angle support bracket that secures interior panels, shelves, or trim inside your range. Replace if cracked, bent, or missing to maintain proper alignment.

Insulation assembly for gas ranges. Installs around oven cavity to retain heat and improve efficiency. Replace if torn, compressed, or missing.

Uneven oven cooking or hot spots? This rear deflector directs heat away from the back wall for even baking. Simple snap-in installation.

Seals between the oven light lens and liner to keep grease and moisture out. Replace if damaged, cracked, or no longer sealing properly.

Insulation guard that installs under the cooktop surface of your gas range. Replace if cracked, torn, or deteriorated to maintain heat efficiency.

If your oven cooks unevenly or runs too hot, a damaged lower air duct may be blocking proper airflow. This part restores heat distribution beneath the cavity.

Mounting screw for refrigerator doors, shelves, kickplates, and interior components. Replace missing, stripped, or corroded screws during repairs.

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.