Parts for Ge PGB960EEJ1ES: Lower Oven Parts

Base spacer for gas ranges. Installs at the bottom of the range to provide proper spacing and support. Replace if cracked, broken, or missing.

A small mounting spacer that positions and supports internal components for proper alignment and clearance. Replaces a worn or damaged spacer to help maintain stable assembly fit and reduce interference between parts. What it does:

• Provides spacing between appliances' internal assemblies to ensure correct alignment
• Helps prevent metal-to-metal contact that can cause noise, wear, or improper sealing
• Restores correct fit when an original spacer is cracked, missing, or deformed
• Commonly used during repair of panels, assemblies, or mounting brackets

• Disconnect power (and gas if applicable) before starting any repair
• Handle surrounding panels and components carefully to avoid damage
• Installation may require removal of adjacent trim or brackets and a few fasteners

Fix an oven that won't hold temperature or runs too hot or cold. This temperature sensor monitors and regulates oven cavity heat for accurate baking.

This barrier bottom floor is the inner bottom panel that helps form the refrigerator's lower compartment, keeping components supported and directing moisture away from sensitive areas. Replaces a damaged, cracked, or missing bottom barrier to restore proper fit and protection. What it does:

• Replaces a cracked, broken, or warped bottom floor panel that can let debris or moisture reach components
• Restores the intended lower-compartment barrier that helps direct condensation and defrost water
• Provides a stable mounting surface for lower shelving/crisper assemblies and nearby components
• Helps reduce the chance of visible gaps or misalignment in the refrigerator base

• Disconnect power and empty the lower compartment before beginning work
• May require removal of lower drawers, trim pieces, or screws/clips for access
• Use basic hand tools; keep track of fasteners and any seals or gaskets removed

Replacement bumper cushion that protects the range frame where panels meet. Install when the original is worn, cracked, or missing to reduce vibration.

Flat wire shelf that slides into your oven's side supports to hold bakeware at the correct height. Replace if bent, warped, or missing a rack position.

This is the bottom panel that sits at the base of the oven cavity, covering the lower heating element or burner area. It helps distribute heat evenly and protects the lower components from spills and debris. Replace this panel if it is warped, cracked, rusted through, or if food drippings have caused permanent damage that affects cooking performance.

Seals your range oven door to maintain proper temperature and efficiency. Replace if worn, cracked, or heat escapes. Verify fit with your model number.

Redirects heat away from the rear panel and components in your gas range oven. Replace if warped, damaged, or missing to protect surfaces.

Metal deflector shield that directs heat inside the oven cavity. Replace if cracked, bent, or missing to restore proper airflow and heat distribution.

If your range burner won't ignite or stays on continuously, this dual plunger switch may need replacement. Moderate DIY repair in about 30 minutes.

Holds and powers the interior oven light bulb for visibility while cooking. Replace if light flickers, won't turn on, or bulbs burn out frequently. Verify fit by your model number before ordering.

Positions and supports internal components to maintain proper alignment and clearance. Replace if cracked, broken, or missing to restore stability.

Right-side lower support base that secures and stabilizes the range cabinet. Replace if cracked, broken, or worn to restore proper alignment and fit.

Replaces the left lower support base that stabilizes your range's lower assembly. Needed when the original is cracked, broken, or missing.

Metal angle support bracket that secures interior panels, shelves, or trim inside your range. Replace if cracked, bent, or missing to maintain proper alignment.

Insulation wrap that lines the oven cavity to retain heat and improve efficiency. Replace if torn, compressed, or missing to restore proper insulation.

Insulation assembly for gas ranges. Installs around oven cavity to retain heat and improve efficiency. Replace if torn, compressed, or missing.

Uneven oven cooking or hot spots? This rear deflector directs heat away from the back wall for even baking. Simple snap-in installation.

Seals between the oven light lens and liner to keep grease and moisture out. Replace if damaged, cracked, or no longer sealing properly.

Insulation guard that installs under the cooktop surface of your gas range. Replace if cracked, torn, or deteriorated to maintain heat efficiency.

If your oven cooks unevenly or runs too hot, a damaged lower air duct may be blocking proper airflow. This part restores heat distribution beneath the cavity.

Size: 10-32 GXTT FLP.595 S