Parts for Ge PGS960EEL2ES: Lower Oven Parts

This receptacle assembly provides the appliance's electrical socket interface, replacing a worn or damaged terminal connection to restore reliable power delivery. Use it to stop intermittent power loss or poor connection at the appliance receptacle. What it does

• Replaces the appliance's electrical receptacle/terminal socket that the wiring plugs into.
• Restores a secure connection when the original terminal is cracked, burned, or loose.
• Can stop intermittent power, sparking, or loss of function caused by a faulty receptacle.
• Supports safe, consistent power transfer between the wiring harness and appliance components.

• One receptacle assembly.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Tighten any retaining screws and ensure terminals fully seat to prevent arcing.

The Temperature Sensor Assembly is an OEM replacement part for GE ovens and ranges. It monitors and regulates the temperature inside the oven cavity to determine accurate and consistent baking and roasting.

Causes of a bad temperature sensor can include damage to sensor wires, failure of electronic modules, or sensors reaching the end of their lifespan after years of high temperature exposure.

Symptoms of a faulty temperature sensor include:

• Inability to achieve or maintain the set oven temperature
• Wide fluctuations outside an acceptable temperature range
• Premature or delayed cycling of heating elements
• Error codes related to temperature sensing issues

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This barrier bottom floor is the inner bottom panel that helps form the refrigerator's lower compartment, keeping components supported and directing moisture away from sensitive areas. Replaces a damaged, cracked, or missing bottom barrier to restore proper fit and protection. What it does:

• Replaces a cracked, broken, or warped bottom floor panel that can let debris or moisture reach components
• Restores the intended lower-compartment barrier that helps direct condensation and defrost water
• Provides a stable mounting surface for lower shelving/crisper assemblies and nearby components
• Helps reduce the chance of visible gaps or misalignment in the refrigerator base

• Disconnect power and empty the lower compartment before beginning work
• May require removal of lower drawers, trim pieces, or screws/clips for access
• Use basic hand tools; keep track of fasteners and any seals or gaskets removed

Replacement front frame bumper that cushions and supports the appliance's front frame or door trim, helping reduce vibration and prevent metal-on-metal contact—restoring a secure, quiet fit for the door or trim assembly. What it does:

• Cushions the front frame/door trim to prevent wear, chipping, and metal rubbing.
• Helps align and stabilize the door/frame for proper closing and fit.
• Reduces rattling and vibration noise during operation.
• Commonly replaced when the door feels loose, rubs against the cabinet, or makes noise.

• Disconnect power to the appliance before beginning any repair.
• May require removal of the door trim or front panel—use basic hand tools and keep fasteners organized.
• Seat the bumper fully in its mounting location; avoid forcing or deforming the part.

Oven deflector redirects oven heat away from the rear panel and components to protect surfaces and help restore more even cooking. Fits in the rear of the oven cavity and replaces a warped or damaged deflector. What it does:

• Directs and deflects heat away from the oven back wall to reduce hot spots and help improve cooking consistency.
• Protects interior liners and nearby components from excessive heat that can cause warping or discoloration.
• Common replacement signs: visible dents, warping, heat discoloration, or uneven baking/broiling.

• Disconnect electrical power (and gas supply for gas ovens) before starting any repair.
• Remove oven racks and mounting hardware; handle part carefully—edges may be sharp.
• Install in the original orientation and secure with the original fasteners; replace missing fasteners with appropriate OEM parts.

This oven deflector directs heat away from the oven's back wall to promote more even cooking and protect internal components from direct heat. It replaces a bent, missing, or damaged deflector to restore proper heat flow in the oven. What it does:

• Redirects burner/element heat away from the back wall to reduce hot spots and uneven baking
• Protects the oven back panel and internal components from direct flame or intense radiant heat
• Helps maintain more consistent oven temperatures during baking and roasting
• Visible or damaged deflectors can cause scorch marks, warped panels, or uneven cooking

• Disconnect power to the appliance (or turn off gas and power for gas ranges) before starting any work
• Remove oven racks for access; installation typically requires basic hand tools (screwdriver)
• Handle the part carefully—edges may be sharp; align tabs or screw holes per the oven's mounting points

The Plunger Switch is an OEM part for GE gas ranges. It is an electro-mechanical component that activates the burners and bake/broil modes when the oven door is securely closed.

Causes of failure include worn contact points, damaged wiring, or defective internal components.  

Symptoms of a bad plunger switch include:

• Inability to select oven cooking functions when door is closed
• Error messages related to unsafe door conditions  
• Random activation of burners with door open 
• Failure of door interlock safety feature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

The Oven Lamp Holder is an OEM part for GE ovens. This component securely holds the oven light bulb in place, ensuring proper illumination inside the oven cavity for better visibility during cooking and baking.

Causes of a bad lamp holder can include repeated exposure to high temperatures, physical damage, or electrical issues. A malfunctioning lamp holder can lead to the oven light not functioning correctly or at all.

Symptoms of a bad oven lamp holder include:

• The oven light not turning on
• Flickering or intermittent operation of the light
• Visible damage or corrosion to the lamp holder
• The light bulb not staying securely in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven deflector is a metal shield that directs heat away from sensitive areas inside the oven cavity to help ensure even cooking and protect surrounding components. It restores proper airflow and helps prevent hot spots. What it does:

• Directs and deflects oven heat to promote more even temperature distribution
• Protects internal components and wiring from direct heat exposure
• Helps reduce localized overheating that can cause oven damage or uneven baking
• Replaces a worn, bent, or missing deflector to restore original airflow path

• One oven deflector

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Typical install requires basic hand tools; follow the manufacturer service instructions
• Handle the part carefully to avoid sharp edges; wear gloves if needed

This oven light gasket fits between the glass lens and the oven liner. It restores a proper seal around the light opening to help keep grease and moisture out of the light cavity and hold the lens securely in place. What it does:

• Seals the joint between the oven light lens and the cavity wall
• Helps prevent grease and moisture from entering the light assembly
• Keeps the lens snug to reduce looseness or rattling
• Replace if the gasket is cracked, flattened, brittle, missing, or if moisture/grease is visible around the lens

• One oven light lens gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/retainer as your model requires (unscrew lens or release clips)
• Note gasket orientation and clean the mating surfaces
• Seat the new gasket evenly and reinstall the lens; do not overtighten the glass

The Latch Automatic is an OEM component specifically designed for GE ranges. It is responsible for automatically latching and locking the oven door securely in the closed position.   

Symptoms of a bad automatic latch include:

• The door not latching or locking fully when closed  
• Difficulty keeping the door securely shut
• Inability to automatically engage the latch

Causes of a bad automatic latch can include wear and tear from extended use over time, broken or loose gears and springs, or damage that impairs the proper functioning of the latching mechanism.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This bottom duct directs airflow beneath the oven cavity to protect components and help maintain even cooking temperatures. It replaces a damaged or rusted lower oven duct to restore proper heat flow and clearance. What it does

• Channels hot air away from the oven base and toward vent paths to help heat distribution.
• Prevents direct heat exposure to the oven's lower insulation and wiring.
• Common replacement when the duct is bent, corroded, or has holes that allow leaks.
• Alleviates uneven baking or excessive heat in adjacent cabinetry when damaged.

• One bottom duct (lower oven air duct).

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Removal typically requires opening the oven door, removing racks and the oven floor or access panels; basic hand tools are usually sufficient.
• Handle edges carefully—wear gloves to protect from sharp metal.

This angle support is a small metal mounting bracket that stabilizes and secures components inside the appliance, helping keep shelves, panels, or assemblies aligned for reliable operation and safe use. What it does:

• Provides structural support for interior panels, shelves, or trim to prevent sagging or misalignment
• Holds assemblies in the correct position to reduce rattling and vibration during use
• Restores proper fit and clearance when a bent or broken bracket causes shifting
• Works with fasteners to anchor components where a right-angle connection is needed

• Inspect surrounding parts and fasteners; replace any damaged screws or clips as needed
• Use the correct size fastener and torque to avoid stripping or cracking adjacent parts
• Disconnect power and follow manufacturer safety guidelines before working near electrical components

This replacement lamp cover protects and diffuses interior appliance light for even illumination and safe bulb containment. It restores a cracked, cloudy, or missing light lens to improve visibility inside the compartment. What it does:

• Protects the interior light bulb from impact, moisture, and food debris.
• Diffuses and softens the bulb's light for more even interior illumination.
• Stops rattling or falling lens issues caused by a cracked or broken cover.
• Helps prevent direct contact with the hot bulb and reduces glare.

• One lamp cover / light diffuser.

• Disconnect power or unplug the appliance before servicing to avoid electrical shock.
• Remove the old cover carefully and dispose of any broken pieces safely.
• Handle the replacement cover gently to avoid cracks; align and snap/slide into place per the original mounting.
• After installation, restore power and replace bulb if still dim or nonfunctional.

Package of 12

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.