Parts for Ge PS960FL4DS: Lower Oven Parts

This rubber rangetop bumper cushions and supports the cooktop, reducing vibration and protecting the surface from metal-on-metal contact. It helps restore proper spacing and reduces rattling or chafing from loose or missing bumpers. What it does:

• Cushions the cooktop edge to prevent scratching and wear
• Keeps the cooktop and rangetop components properly spaced and stable
• Reduces rattling, vibration, and noise during use
• Commonly replaced when bumpers are cracked, flattened, missing, or allow movement

• Remove power to the appliance and allow all surfaces to cool before servicing.
• Access may require lifting or removing the cooktop; follow manufacturer instructions for your model.
• Replace with the same style bumper to maintain proper fit and spacing.
• Use care around sharp edges.

A replacement latch assembly that secures and releases the oven door for normal cooking and self-clean cycles. Restores proper door engagement to help the oven maintain temperature and complete locking cycles safely. What it does:

• Secures the oven door closed so the appliance can heat and maintain temperature.
• Engages/disengages during self-clean or lock cycles to prevent accidental opening.
• Stops common symptoms like a door that won't stay closed or won't latch properly.
• Works as the mechanical interface between the door and the range/oven frame.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access usually requires removing the oven door or front access panel; follow the oven's service instructions.
• Handle springs and small fasteners carefully; keep track of any clips or screws removed.

This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:

• Single-pole, double-throw action directs power between NO/NC circuits based on actuator position
• Used to signal or control a component per the model's design (e.g., latch/lock, relay, fan)
• Failure symptoms can include no activation, stuck-on/off behavior, intermittent operation, or heat-damaged terminals
• Electrical tests may show incorrect continuity between COM–NO/NC when pressed or released

• Includes: 1 SPDT high-amp switch

• Disconnect power at the breaker or unplug the appliance before servicing
• Label or photograph wiring; move leads to matching COM/NO/NC terminals on the new switch
• Mount with the correct actuator orientation and secure any bracket or screws
• Inspect connectors for heat damage; ensure tight spade fits, restore power, and test operation

Range overheating or heating element won't turn off? This high-limit thermostat cuts power when temperatures exceed safe levels. Quick safety fix.

Back heat shield panel for electric ranges. Protects rear components from oven heat. Replace if cracked, warped, or missing to restore proper insulation.

This cover terminal block protects the appliance's power connection area by covering the terminal block where the power cord attaches. It keeps wiring secure and helps reduce risk of accidental contact and shorting. What it does:

• Covers and protects the power cord terminal block from dust, moisture and accidental contact
• Prevents exposed terminal ends that can cause arcing or shorts
• Helps keep wiring routed and secured at the power connection
• Common replacement when the original cover is cracked, melted or missing

• One cover terminal block

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the cover
• Remove any mounting screws and lift off the old cover to access terminals; document wire locations before disconnecting
• Reinstall cover after confirming tight, correct terminal connections and that no bare conductors are exposed
• If terminals or wiring show damage (burning, melting, corrosion), replace or repair those parts before reinstalling the cover and restore power only when safe

Replace a cracked, dented, or missing side panel on your electric range. This structural cover panel installs on the exterior side of your appliance.

Gray removable oven rack that supports cookware inside your oven. Replace a bent, rusted, or missing rack to restore stable support and proper positioning.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Restores bright interior lighting in your oven or range. Replace when bulb burns out to clearly see food and monitor cooking progress. Verify G9 base fit.

The Lamp Halogen Assembly is an OEM part for GE ranges. It is the internal light bulb that illuminates the oven cavity.

Symptoms of a bad lamp halogen assembly include:

• Dim or flickering oven light
• Stuck-on or unresponsive oven light functionality  
• Burned out or blackened bulb

Causes can be normal life cycle burnout after extended use or damage from excess vibration.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. U

Base rail for electric ranges. Structural support component that mounts at the bottom of the range chassis. Replace if cracked, bent, or damaged.

Secures your range to the floor or wall to prevent forward tipping. Replace if bracket is bent, broken, or missing during appliance relocation.

Strain relief bracket secures and protects the power cord connection on your range. Replace if damaged, cracked, or missing to ensure safe installation.

If burners only heat on high or controls are unresponsive, the machine control relay board may have failed. This board manages power levels and temperature.

If your range burners or oven won't heat or only work intermittently, the relay daughter board may have failed. This control board restores power switching.

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking.

Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age.

Symptoms of an inadequate probe thermistor include:

• Inaccurate temperature readings and baking inconsistencies
• Oven temperature exceeding desired setting risking fire

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Plastic standoff that secures and spaces the control board from the chassis. Replace if broken, missing, or worn to restore proper board mounting and insulation.

The Control Board Assembly is an OEM part for GE electric ranges. It is the central processing unit that controls all cooking functions.

This electronic control board receives input from the control panel and runs self-diagnostic tests to operate range components accordingly. It monitors oven temperature, element output, timers, and other operations essential for optimized cooking performance. 

Causes of a faulty board can include liquid damage, overheating from continuous use, or failure over time.

Symptoms of a bad control board  include:

• Elements or bake/broil functions not working properly  
• Inability to set or maintain oven temperature
• Timers and presets malfunctioning or unresponsive  
• Appliance not powering on as expected

Replacing with this genuine OEM GE part restores the fully controlled operation of the range. Also compatible with Hotpoint, KitchenAid, and some Kenmore electric range models. 
 

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement 8-18 screw with a SKT25 drive used to secure panels and components on compatible appliances. It restores proper fastening and helps eliminate loose or rattling parts for safer, quieter operation. What it does:

• Fastens panels, brackets, and internal components where 8-18 thread hardware is required
• Replaces missing or stripped screws that cause loose panels or vibration
• Helps keep wiring and assemblies properly secured to prevent shifting during use
• Uses a SKT25 (Torx/socket) drive for a secure, tamper-resistant fit

• Use the correct SKT25 driver or bit to avoid cam-out and fastener damage
• Tighten securely but avoid over-torquing to prevent thread or component damage
• Disconnect power to the appliance before working on electrical panels or internal components
• If a screw is severely corroded or a hole is damaged, replace with the correct OEM fastener and repair the mounting point as needed

Replacement washer for ranges and ovens. Used to secure components and provide even fastening. Replace if cracked, worn, or missing during repairs.

This 10-32 x 3.30 screw with a Torx T20 drive secures panels and components in place to restore safe, rattle-free operation. Use when worn or missing screws cause loose trim, control panels, or internal assemblies. What it does

• Fastens panels, brackets, and components using a 10-32 thread for a secure hold
• Replaces stripped, corroded, or missing screws that cause vibration or rattling
• Helps maintain proper alignment of control panels and internal parts
• Restores grounding/retention where original screws are required for safety

• One 10-32 x 3.30 Torx T20 screw (quantity: 1)

• Use the correct Torx T20 driver to avoid damaging the screw head
• Tighten snugly but do not overtighten; replace with identical part for fit and safety
• Power off and unplug the appliance before accessing internal components
• If screws fasten parts involved with grounding or electrical connections, verify secure contact after reinstalling