Magic Chef Knob, Dial & Button

The Top Burner Control Knob is an OEM part for Whirlpool ranges. This knob allows you to control the heat level of the stovetop burners, providing precise adjustments for cooking.

You should replace the control knob if it becomes damaged or worn out. Causes of a bad control knob can include frequent use, accidental impact, or exposure to high temperatures, which can result in the knob becoming loose, cracked, or difficult to turn.

Symptoms of a bad top burner control knob include:

• Difficulty turning the knob
• The knob not staying in place
• Cracks or visible damage
• Inconsistent heat levels when adjusting the burner

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: black. It measures about 2 inches in diameter.

Color: black. Measures about 2 inches in diameter.

Fresh food section. Color: clear. Measures about 3 inches in diameter.

Color: black. Measures about 2 inches in diameter.

Replace a worn or missing surface-burner knob with this black infinite switch control knob. It restores smooth, accurate heat selection on your range or cooktop when the original knob is cracked, stripped, loose, or missing. What it does:

• Interfaces with the surface burner's infinite switch to select OFF through Low–High heat levels
• Restores positive, secure control of the burner
• Typical symptoms: knob cracked, spins freely, falls off, or can't adjust temperature
• Helps ensure consistent response when turning the burner on/off and setting heat

• Disconnect power and allow the cooking surface to cool completely
• Pull the old knob straight off the switch shaft
• Align the new knob with the shaft and press on until fully seated; do not force
• Rotate through all settings to confirm smooth operation

The Range Clock Knob is an OEM part for Whirlpool ranges. It attaches to the center of the oven control panel and allows users to adjust the built-in clock, serving as the primary control for setting or correcting the time. 

Over time, the clock knob can become faulty due to regular use leading to internal stripping or wear, exposure to heat causing cracks or warping, or accidental impacts damaging the knob.

Color: Black

Symptoms of a defective range clock knob include:

• Difficulty setting or adjusting the clock
• The knob spins freely without engaging the control shaft
• The knob feels loose, cracked, or broken

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This thermostat knob fits onto the control shaft so you can select and adjust cooking temperature. Replace a cracked or stripped knob to restore smooth operation and a clean, finished look.

• Attaches to the thermostat stem to allow manual temperature selection
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob spins without engaging or won't stay on the shaft
• Restores proper control feel and appearance

• Disconnect power to the appliance and allow surfaces to cool before service
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft and press straight on until fully seated; do not force
• The pointer aligns with the control markings before use

Replace a worn, cracked, or missing surface burner knob to restore smooth, precise heat control on your cooktop. This direct-fit knob brings back easy ON/OFF operation and clear setting alignment for everyday cooking.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame or heat level
• Common symptoms: knob cracked or stripped, spins freely or falls off, melted/discolored, or missing
• Restores proper pointer alignment and a clean, finished look
• Designed for the surface burner position; match style and shaft orientation to your original

• Allow the appliance to cool completely before servicing
• Pull the old knob straight off the valve stem; do not pry against the control panel
• Align the stem orientation with the new knob and press straight on until fully seated
• Disconnect power or shut off gas before any work near controls

Replacement control knob for the oven thermostat. It installs on the thermostat shaft so you can select cooking temperatures. Replaces a cracked, loose, or missing knob to restore smooth adjustment and clear, readable settings. What it does:

• Provides the hand control to turn the oven's thermostat and set temperature
• Press-fits onto the thermostat shaft for consistent, aligned operation
• Restores a secure grip and pointer alignment when the original is worn
• Common symptoms: knob cracked, falls off, spins freely, or markings are hard to read

• One white thermostat control knob

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Pull the old knob straight off the thermostat shaft—avoid prying against the panel
• Align the new knob with the shaft flat and press straight on until fully seated
• The pointer aligns with Off; remove and reseat if needed

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

This white switch knob replaces a damaged or missing control knob, restoring a clean look and smooth, confident operation when selecting settings. It press-fits onto the control shaft so you can adjust functions without wobble or slip.

• Attaches to the control switch shaft to turn and select settings
• Replace if the knob is cracked, stripped, loose/wobbly, or missing
• Common symptoms: knob falls off, won't engage the switch, or is hard to turn
• Normal wear, heat, or impact can damage the original knob over time

• Disconnect power and ensure the appliance is cool before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel or switch stem
• Align the new knob with the shaft and press straight on until fully seated
• Verify alignment with the OFF position and test operation

Color: black. It measures about 2 inches in diameter.

This burner valve knob replaces a worn or missing surface burner control so you can turn the gas on/off and set flame levels precisely. It restores smooth, secure control of your cooktop's surface burners.

• Mounts to the surface burner valve stem to control gas flow and flame height
• Restores accurate turning and feel when the original knob is cracked, stripped, or loose
• Common symptoms: knob falls off, won't engage the stem, hard to adjust flame, missing knob
• Helps ensure the burner reliably turns fully Off and adjusts smoothly through settings

• Turn all controls OFF and allow the cooktop to cool before servicing
• Unplug or disconnect power to the range for safety
• Pull the old knob straight off; align the new knob with the valve stem (match the flat/D-shaped side) and push straight on—do not force
• Confirm smooth operation and proper Off alignment after installation

This replacement control knob fits the surface element infinite switch, allowing you to turn the burner on and set the heat level. Replace a cracked or missing knob to restore safe, accurate burner control.

• Attaches to the surface burner's infinite switch to select OFF through heat settings
• Restores positive grip when the original knob is cracked, stripped, or missing
• Typical symptoms: knob spins freely, won't stay on, is hard to turn, or has broken pointer
• Helps ensure clear setting indication and consistent adjustment

• Disconnect power to the range/cooktop before servicing
• Pull the old knob straight off the switch shaft—no tools required
• Align the new knob with the switch shaft and press firmly until fully seated
• The pointer aligns correctly with OFF and heat settings

Color: White