Magic Chef Wall Oven Parts

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

Color: black. It measures about 2 inches in diameter.

Replacement cold control that restores temperature regulation in compatible refrigerators. Installs behind the temperature knob to control compressor cycling, helping stabilize interior temperature and stop constant running or temperature swings. What it does:

• Regulates refrigerator temperature by switching compressor/fan operation on and off.
• Replaces a failed temperature control that causes inconsistent cooling or interior temps that are too warm or too cold.
• Can stop issues like the compressor running continuously or frequent temperature fluctuations.
• Works with compatible refrigerator control housings and knobs.

• Disconnect power before replacing the control to avoid shock or injury.
• Note wire locations and knob orientation before removing; reconnect wires to the same terminals.
• Handle the control carefully and avoid bending or stressing mounting tabs and contacts.
• After installation, restore power and verify proper cycling and temperature stabilization.

This burner valve knob replaces a worn or missing surface burner control so you can turn the gas on/off and set flame levels precisely. It restores smooth, secure control of your cooktop's surface burners.

• Mounts to the surface burner valve stem to control gas flow and flame height
• Restores accurate turning and feel when the original knob is cracked, stripped, or loose
• Common symptoms: knob falls off, won't engage the stem, hard to adjust flame, missing knob
• Helps ensure the burner reliably turns fully Off and adjusts smoothly through settings

• Turn all controls OFF and allow the cooktop to cool before servicing
• Unplug or disconnect power to the range for safety
• Pull the old knob straight off; align the new knob with the valve stem (match the flat/D-shaped side) and push straight on—do not force
• Confirm smooth operation and proper Off alignment after installation

This replacement control knob fits the surface element infinite switch, allowing you to turn the burner on and set the heat level. Replace a cracked or missing knob to restore safe, accurate burner control.

• Attaches to the surface burner's infinite switch to select OFF through heat settings
• Restores positive grip when the original knob is cracked, stripped, or missing
• Typical symptoms: knob spins freely, won't stay on, is hard to turn, or has broken pointer
• Helps ensure clear setting indication and consistent adjustment

• Disconnect power to the range/cooktop before servicing
• Pull the old knob straight off the switch shaft—no tools required
• Align the new knob with the switch shaft and press firmly until fully seated
• The pointer aligns correctly with OFF and heat settings

This white switch knob replaces a damaged or missing control knob, restoring a clean look and smooth, confident operation when selecting settings. It press-fits onto the control shaft so you can adjust functions without wobble or slip.

• Attaches to the control switch shaft to turn and select settings
• Replace if the knob is cracked, stripped, loose/wobbly, or missing
• Common symptoms: knob falls off, won't engage the switch, or is hard to turn
• Normal wear, heat, or impact can damage the original knob over time

• Disconnect power and ensure the appliance is cool before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel or switch stem
• Align the new knob with the shaft and press straight on until fully seated
• Verify alignment with the OFF position and test operation

This door handle spacer fits between the handle and the door panel, providing the correct standoff and a clean, finished look. Replacing a worn spacer helps keep the handle secure and aligned.

• Maintains proper spacing between the handle and door surface
• Helps stabilize a loose or wobbly handle
• Replaces cracked, discolored, or missing spacers
• Color: Bisque (cream/tan finish) to match compatible appliances

• Disconnect power and allow the appliance to cool before servicing
• Support the door and handle while removing mounting screws
• Transfer or replace spacers on both sides of the handle if needed; do not overtighten screws
• Wear gloves to protect hands and avoid stressing glass panels

This broil element is the oven's upper heating element that provides direct, high-heat cooking for broiling and browning. It restores the oven's broil function so foods brown evenly and cook from above. What it does:

• Heats the top of the oven cavity to produce direct radiant heat for broiling and browning
• Replaces a damaged, burned out, or non-heating upper oven element
• Commonly used when broil cycles fail or food doesn't brown on top
• Works with ovens that use a straight tubular broil element design

• Disconnect power to the range at the breaker or unplug before starting
• Element mounts with two screws accessible from inside the oven; handle glass and trim carefully
• Verify electrical connections are tight and correct before restoring power

The Regulator is an OEM replacement part for Whirlpool gas ranges. It regulates the flow of gas from the supply line to the burners, ensuring safe and efficient operation of your range. It maintains a consistent gas pressure, allowing for accurate and controlled heat distribution during cooking.

A bad pressure regulator can occur due to wear and tear, clogging, or damage to the internal components. If you notice symptoms such as uneven flame, difficulty in igniting the burners, or gas leaks, it may be time to replace the pressure regulator.

Symptoms of a bad gas pressure regulator include:

• Uneven flame
• Difficulty in igniting burners
• Gas leaks

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This white control knob replaces a worn or missing knob so you can smoothly select settings on your appliance again. It restores dependable turning feel and a clean, like-new appearance on the control panel.

• Attaches to the control shaft so you can select levels or functions
• Common fix for cracked, stripped, loose, or missing knobs
• Helps when the knob spins freely or is hard to turn
• Maintains clear alignment with the panel's indicator marks

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the old knob straight off the shaft
• Align the new knob with the flat or splined shaft and press on until fully seated
• Verify smooth movement from OFF through all settings

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

This conversion kit provides the orifices and instructions needed to convert a compatible gas range/oven from natural gas to liquid propane, restoring proper fuel flow and safe burner operation after a fuel-type change. What it does:

• Replaces factory natural-gas orifices with LP orifices sized for propane fuel
• Helps restore correct flame height and even heating when switching to LP
• Addresses weak or irregular flames that occur after changing fuel types
• Ensures burners receive the proper fuel jetting for safe LP operation

• Installation should follow OEM instructions exactly
• Turn off gas supply and electrical power before beginning work
• Use proper leak testing after installation and before returning the appliance to service
• Regulator adjustment or replacement may be required per OEM service instructions

Color: White

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This drip bowl catches and channels excess moisture or drips to help keep the area under the dispenser or ice/water outlet clean and dry. Durable molded plastic resists staining and is shaped for correct fit and drainage. What it does:

• Collects and directs drips from the dispenser or outlet to prevent pooling
• Helps reduce water on the cabinet floor and in the drip tray area
• Restores proper alignment and containment when the original bowl is cracked or warped
• Compatible with units that use an 8" black drip bowl as the dispenser/collector component

• One 8" black drip bowl

• Remove power to the appliance before beginning any service
• Typically snaps or slides into place; check for retaining clips or mounting tabs
• Inspect surrounding seals and gaskets; replace if damaged to prevent leaks