Parts for Electrolux E30EC70FSS1: 05 - Main Top Parts

This replacement cover restores the appliance's exterior appearance and protects the console/control area from dust and debris. It fits over the control area to conceal components and give the front a finished look. What it does:

• Protects internal console components from dust and moisture that can affect controls
• Conceals wiring and switches for a clean, factory appearance
• Helps reduce rattles or movement around the control area
• Restores cosmetic damage from cracks, chips, or missing trim

• One cover

• Disconnect power before starting any repair to avoid shock or accidental activation
• Handle the part carefully; plastic trim can crack if forced
• Typical installation requires removal of a few screws or clips—use basic hand tools
• Keep fasteners and mounting clips from the old cover if they are undamaged; replace if missing

6 inch, 1200 watt single radiant surface element.

Used on the 1200 watt element

Used on the 2500 watt element

This replacement cabinet insulation panel helps reduce heat transfer and stabilize internal refrigerator temperatures for more consistent cooling. It also dampens vibration and can help reduce frost buildup when sealed and installed correctly. What it does:

• Replaces damaged or missing cabinet/liner insulation that allows warm air infiltration.
• Helps maintain proper internal temperatures and can reduce long compressor run times.
• Reduces localized warm spots and helps limit excess frost or moisture where insulation is compromised.
• Dampens vibration and reduces noise from compressor and internal components.

• One cabinet insulation panel

• Disconnect power and remove food before servicing; work slowly to avoid damage to liner or refrigerant lines.
• Installation typically requires removing interior trim or liners; panels may be held with adhesive, clips, or screws.
• Wear gloves and a dust mask when handling older insulation; clean mating surfaces before installing replacement.

Specs: 10-32 X 0.375

Specs: 8 - 18 x 0.500

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

These are replacement countertop mounting screws that secure the appliance to the countertop or cabinet, restoring a stable, flush fit and preventing movement or gaps. Sold as a 2-pack for quick, direct replacement. What it does

• Secures the appliance countertop or trim to the cabinet or counter to keep the unit from shifting.
• Helps eliminate rocking, gaps, or uneven alignment caused by missing or loose mounting screws.
• Restores proper fit and finish where original mounting hardware has been lost or damaged.
• Works with factory mounting points and standard driver heads for straightforward replacement.

• Two countertop mounting screws.

• Use the correct-size driver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or damage the cabinet/countertop.
• Keep original brackets and hardware; replace only the missing or damaged screws as needed.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation