Mastercut Parts

Attaches to the back of your walk-behind mower deck to prevent grass and debris from reaching the operator. Replace if cracked, broken, or missing.

Replace a broken torsion spring causing handle slack or engagement issues on your lawn mower. Common DIY repair restores proper tension and operation.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

Throttle control won't adjust engine speed or feels sticky? This throttle control box restores smooth speed regulation on lawn tractors and tillers.

Metal blade support spacer that mounts between the mower blade and bolt. Secures the blade to the deck base. Replace if worn, damaged, or missing.

This replacement part is a pulley spacer intended for use in different lawn mowers. This is a genuine replacement part made by MTD. Pulley spacers allow the pulley to rotate while providing a gap so that friction does not build up inside the machine and create extra heat.A new pulley spacer might be needed if the current one is damaged or broken in any way. It is common for this part to be replaced after years of normal wear and tear. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide.This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn mowers made by MTD.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Replacement torsion spring for lawn and garden equipment engines. Creates tension between levers and components. Replace if broken, overstretched, or distorted.

Fastener pin that secures nuts and bolts in lawn mower engines and assemblies. Replace if bent, missing, or damaged during maintenance or repair work.

The exhaust systems on lawn and garden equipment are just as important as those on a vehicle. They need a good seal to prevent a leak between the carburetor and the exhaust tube, which would allow air leakage that could cause performance issues and loud noise. Over time all exhaust gaskets deteriorate and require a full replacement. It is relatively easy to replace an exhaust gasket and requires only the use of screw drivers, a socket set or a wrench set depending on the device being service. Replacement components such as sockets or screws may also be required during this repair. The gasket surfaces should be cleaned and fully dried before being installed between the carburetor and the exhaust tube. This exhaust gasket works with Toro, Simplicity, Murray and Briggs & Stratton lawnmowers, generators, snowblowers, wood chippers, and lawn tractors. It also works with equipment made by Craftsman, Husqvarna, Cub Cadet, Poulan, Wheel Horse, MTD, Ariens, and more.

This is a self-tapping screw. It attaches to various lawn machines' engines. The exact location depends on the make and model of the device. With age or misuse of the lawn equipment, the self-tapping screw may become damaged or break. One sign that the screw is gone or broken is a loose connection between the engine and the foundation that it sets on. Excessive vibration is another indicator that the self-tapping screw is missing or damaged. If it does wear out and get lost or damaged, the part must be replaced.It is easy to replace a self-tapping screw. First, make sure that the device is cooled. Wear gloves for protection. It requires a wrench to install. If the self-tapping screw breaks, other tools such as pliers may be needed to get the screw out.The self-tapping screw is a genuine OEM part supplied by the manufacturer. It is made of durable metal. The self-tapping screw is sold individually. It is compatible with machines produced by Troy-Bilt, Bolens, Yard-Man, Yard Machines, Cub Cadet, and Husky. It is used in a variety of lawn tractors, lawnmowers, and other lawn equipment engines.

Wing nut for lawn tractors and outdoor power equipment. Secures covers, guards, and components. Replace if stripped, missing, or damaged.

Extension spring for riding mowers and lawn tractors. Replaces worn, broken, or missing springs in various linkage and control systems. Direct fit part.

Extension spring for lawn tractors and riding mowers. Replace if stretched, broken, or causing poor engagement. Verify fit with your model number.

Flange bearing for lawn tractors and riding mowers. Replace if you notice excessive noise, vibration, or wheel wobble. Verify fit with your model number.